• 한국결정성장학회지
• /
• 제13권5호
• /
• pp.241-246
• /
• 2003

ATO(antimony-doped tin oxide) 투명전도막을 sol-gel dip coating 방법에 의해 $SiO_2$/glass 기판 위에 성공적으로 제조하였다 ATO막의 결정상은 $SnO_2$상임을 확인하였고, 막의 두께는 withdrawal speed를 50 mm/minute로 코팅시 약 100 nm/layer였다. $SiO_2$/glass 기판 위에 코팅한 400 nm두께의 ATO 박막을 질소분위기에서 annealing한 후, 측정한 광 투과율과 전기 저항치는 각각 84%와 $5.0\times 10^{-3}\Omega \textrm{cm}$였다. 이러한 특성은 $SiO_2$막이 Na 이온의 확산을 제어하여 $Na_2SnO_3$ 및 SnO와 같은 불순물의 형성을 억제하고, 막 내부의 Sb의 농도와 $Sb^{3+}$에 대한 $Sb^{5+}$의 비를 증가시키는데 기여했기 때문으로 확인되었다. 또한, $N_2$ annealing은 $Sb^{5+}$뿐만 아니라 $Sn^{4+}$를 환원시킴으로써 전기전도도를 향상시킴을 확인하였다.

• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.911-919
• /
• 1994

As the study for preparation of single-layer anti-reflective coating on glass, the conditions of synthesis of sol for coating and of reproducible coating procedure were investigated. In case of water-based sol, coating was impossible because of poor wettability of sol. The Substitution of solvent with ethanol improved the wettability of sol on the glass surface, and optimum amount of ethanol for substitution was 70 vol%. Maximum specific surface area and total pore volume of water-based sol were 268.7$m^2$/g and 0.315 cc/g, but after substitution, those values increased to 404.1 $m^2$/g and 0.376 cc/g, respectively. The upper limit withdrawl speed of coating in order to get clean coated films without aggregations or stains was 7 cm/min. In case of addition of 0.1 mol HNO3 and substitution with 70 vol% ethanol and heat-treatment at 40$0^{\circ}C$ for 1 hour, thin film with thickness of 94 nm was obtained at withdrawl speed of 4 cm/min. The thickness of thin film was independent of drying time.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.455-458
• /
• 2001

The thin films of high pemitivity in ferroelectric materials using a capacitor are applied to DRAMs and FRAMs. (Ba, Sr)$TiO_3$ thin films as ferroelectric materials were prepared by the sol-gel method and made by spin-coating on the Pt/Ti/$SiO_2/Si$ substrate at 4,000 [rpm] for 10 seconds. The devices of BST thin films to composite $(Ba_{0.7},Sr_{0.3})TiO_3$ were fabricated by changing of the depositing layer number on $Pt/Ti/SiO_2/Si$ substrate. The thin film capacitor to be ferroelectric devices was investigated by structural and electrical properties. The thickness of BST thin films at each coating numbers 3, 4 and 5 times was $2500[\AA]$, $3500[\AA]$, $3800[\AA]$. The dielectric factor of thin film when the coating numbers were 3, 4 and 5 times was 190, 400 and 460 on frequency l[MHz]. The dielectric loss of BST thin film was linearly increased by increasing of the specimen area.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.455-458
• /
• 2001

The thin films of high permitivity in ferroelectric materials using a capacitor are applied to DRAMs and FRAMs. (Ba, Sr)TiO$_3$ thin films as ferroelectric materials were prepared by the sol-gel method and made by spin-coating on the Pt/Ti/SiO$_2$/Si substrate at 4,700 [rpm] for 10 seconds. The devices of BST thin films to composite (Ba$\_$0.7/Sr$\_$0.3/)TiO$_3$ were fabricated by changing of the depositing layer number on Pt/Ti/SiO$_2$/Si substrate. The thin film capacitor to be ferroelectric devices was investigated by structural and electrical properties. The thickness of BST thin films at each coating numbers 3, 4 and 5 times was 2500[${\AA}$], 3500[${\AA}$], 3800[${\AA}$]. The dielectric factor of thin film when the coating numbers were 3, 4 and 5 times was 190, 400 and 460 on frequency 1[MHz]. The dielectric loss of BST thin film was linearly increased by increasing of the specimen area.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.118-124
• /
• 2016

In this study, experiments are conducted to improve spray coating uniformity by using second and third electrodes based on the electrospray atomization mechanism. The uniformity of fabricated thin films can be improved by adjusting the design of the second electrode. The implementation of the second electrode with an elongated hole and a bending angle of $90^{\circ}$ results in highly uniform films. In addition, induced area to substrate is increased by lowering the applied voltage using the third electrode with a round rod shape. A linear correlation between applied voltage and induced area is confirmed. Thin film thickness and surface roughness are measured after the fabrication of thin films through the electrospray process. It is confirmed that a thin film is formed having an average thickness of 273.44 nm, a thickness uniformity of less than 10%, and a surface roughness of 3 nm.

• 한국재료학회지
• /
• 제10권4호
• /
• pp.264-269
• /
• 2000

$TiO_2$sol(30wt%, anatase)을 이용하여 스핀코팅으로 유리기판에 $TiO_2$박막을 제조하였다. 박막의 두께는 코팅주기의 횟수가 조절하였다. 한 코팅주기는 스핀코팅, 건조, 열처리를 포함한다. 박막의 반응성은 막 위에서의 자외선강도가 0.44와 2.mW/$\textrm{cm}^2$인 조건에서 벤젠기체의 광분해 속도를 통해 조사하였다. 박막의 두께가 증가할수록 표면적으로 증가로 인해 반응성은 증가하였으며, 0.44mW/$\textrm{cm}^2$일 때 4$\mu\textrm{m}$정도 이상의 두께에서 반응성은 더 이상 증가되지 않았다. porous한 $TiO_2$박막은 비교적 넓은 유효표면적을 가지고 있으며, 그것은 비교적 높은 자외선 강도하에서 박막두께에 따라 반응속도를 증가시키는 결과를 낳았다.

• 한국정밀공학회지
• /
• 제31권6호
• /
• pp.491-495
• /
• 2014

We developed a compact high-precision slot-die coating machine for thin-film deposition on a flexible substrate. For smooth and precise coating, air-bearing and linear motor system were employed to minimize velocity ripple. The gap control mechanism is specially designed to have repeatability of gap between nozzle and substrate under 1 ${\mu}m$. Due to extremely precise gap control, the machine can coat thin-films down to 50 nm with $200mm{\times}100mm$ size. A thin film of Ag nano-particle ink is coated for demonstration.

• 한국세라믹학회지
• /
• 제31권7호
• /
• pp.795-803
• /
• 1994

Ferroelectric BaTiO3 thin film was produced using BaTi-ethoxide sol. This sol was prepared from BaTi-ethoxide by a partial hydrolysis with ammonia as a basic catalyst and ethylene glycol as a chelating agent. BaTiO3 thin film was prepared from three continuous spin-coating layers of the sol on bare Si(100) wafer at 2500 rpm followed by pyrolysis at $700^{\circ}C$ for 30 min. After the heat treatment, the film was 0.200$\pm$0.010 ${\mu}{\textrm}{m}$ thick and its grain size was 0.059 ${\mu}{\textrm}{m}$. On the other hand, electrical properties were measured for BaTiO3 thin film separately prepared on Au-deposited silicon wafer. The dielectric constant and loss of the BaTiO3 thin film at room temperature was 150~160 and 0.04 respectively, which was measured at 10 kHz and oscillation level of 0.1 V. In the measurements of the dielectric properties at high temperatures, it was observed that the capacitance of the thin film increases steeply, while the dielectric loss reaches maximum around 1$25^{\circ}C$, which corresponds a phase transition from tetragonal to cubic BaTiO3.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.416-416
• /
• 2016

Organic-inorganic metal halide perovskite solar cells have received attention because it has a number of advantages with excellent light harvesting, high carrier mobility, and facile solution processability and also recorded recently power conversion efficiency (PCEs) of over 20%. The major issue on perovskite solar cells have been reached the limit of small area laboratory scale devices produced using fabrication techniques such as spin coating and physical vapor deposition which are incompatible with low-cost and large area fabrication of perovskite solar cells using printing and coating techniques. To solution these problems, we have investigated the feasibility of achieving fully printable perovskite solar cells by the blade-coating technique. The blade-coating fabrication has been widely used to fabricate organic solar cells (OSCs) and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Moreover, the film morphology control in the blade-coating method is much easier than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be performed by using a precisely polished blade with low surface roughness and coating gap control between blade and coating substrate[1]. In order to fabricate perovskite devices with good efficiency, one of the main factors in printed electronic processing is the fabrication of thin films with controlled morphology, high surface coverage and minimum pinholes for high performance, printed thin film perovskite solar cells. Charge dissociation efficiency, charge transport and diffusion length of charge species are dependent on the crystallinity of the film [2]. We fabricated the printed perovskite solar cells with large area and flexible by the bar-coating. The morphology of printed film could be closely related with the condition of the bar-coating technique such as coating speed, concentration and amount of solution, drying condition, and suitable film thickness was also studied by using the optical analysis with SEM. Electrical performance of printed devices is gives hysteresis and efficiency distribution.

• 한국세라믹학회지
• /
• 제29권3호
• /
• pp.216-222
• /
• 1992

PLZT thin films were prepared using sol-gel spin coating. The films mainly consisted of perovskite phase when heat treated at 600$^{\circ}C$ and in O2 or air atmosphere for 2 hours after 7 coating cycles. Cracks were formed when smaller than after 9 coating cycles. When ITO interlayer existed between Corning 7059 glass substrate and the film, cracks were not formed after 9 coating cycles, but cracks were formed after 11 coating cycles because of large volume change of the film contracting on the substrate during the heat treatment. In the observation of microstructure, the thin films have perovskite phase of about 2 $\mu\textrm{m}$ grain size and pyrochlore phase of 100∼200${\AA}$ grain size.