• Journal of Korean Society on Water Environment
• /
• v.29 no.3
• /
• pp.420-427
• /
• 2013

In this study, the ecological characteristics of Limnoperna fortunei were surveyed as a preceding research to solve the problem such as biofouling or biowaste caused by those organisms in the closed water pipeline. Limnoperna fortunei was collected not in the main reaches of Somjin River but inside and outside of the intake tower which is located in the lower part of Sueo Reservoir. The dense populations were found at the inlet mouth and near part of the pipeline. Their byssuses were formed as a thick and tightly interwind mat. The rusted parts of the pipeline hold relatively more shells than those of the normal parts. Average count of the numbers ranged $12.1{\sim}136.5ind./m^2$ through the sampling stations (A,B and C). The amount of attached shells at each station were A=386, B=258, and C=71, respectively. The relationships of shell height-length and shell length-width were proportional. The majority sizes in each station ranged A=20.01~22.00 mm (33.9%), B=10.01~14.00 mm (51.2%), and C=18.01~20.00 mm (22.5%), 24.01~26.00 mm (21.1%), respectively. Most of the bigger size of shells on C station was found dead. The ecological habitat seemed less suitable for Limnoperna fortunei when they located farther away from the intake tower of reservoir. From now on, it is necessary to consider the continuous monitoring of this organism.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.1
• /
• pp.58-63
• /
• 2010

Introduction : Head trauma is the main cause of death in aircraft crash. In a Michigan study of structurally survivable, fatal accidents, 80% of the fatally injured had received head trauma. We tried to develop a new helmet for passengers, and perform its efficiency test. Methods : An aircraft helmet requires an excellent protection against head trauma, lightness, and small volumes. In addition, it must be wearable, fire resistant, and non toxic when it is burning. We developed two new helmets made from silicone foam which met all theses requirements. One was thin (2.5cm), and the other was thick (6.3cm). These looked like a motorcycle helmet and had only a soft silicone as liner material without an outer hard shell. Therefore we can carry them easily inside aircrafts. The standard test for helmet is Snell's drop test. It measures the impact acceleration of head shaped metal wearing helmet during we drop it at certain heights. Impact sites were total 5 sites (front, back, right, left and top) for each helmet. All these sites were impacted twice. Results : The thickness of impact sites varied from 2.5cm to 6.3cm. The impact acceleration of 2.5cm thickness site when it was dropped from 1.0 meter was 379g. But, that of 6.3cm thickness site when it was dropped from 1.5 meter was only 163g. Unfortunately, both helmets didn't meet the Snell Standard for motorcycle helmets. Discussion : If we add suitable outer hard shell, and change its thickness and design, the efficiency will be increased. A study indicated that helmet could reduce the risk of head trauma up to 85%. We made helmet for passengers in aircraft crash for the first time. If we improve its weak points, it will decrease the frequency of head trauma in aircraft craft.

• Korean Journal of Materials Research
• /
• v.18 no.7
• /
• pp.379-383
• /
• 2008

We report on the light-emitting diode (LED) characteristics of core-shell CdSe/ZnS nanocrystal quantum dots (QDs) embedded in $TiO_2$thin films on a Si substrate. A simple p-n junction could be formed when nanocrystal QDs on a p-type Si substrate were embedded in ${\sim}5\;nm$ thick $TiO_2$ thin film, which is inherently an n-type semiconductor. The $TiO_2$ thin film was deposited over QDs at $200^{\circ}C$ using plasma-enhanced metallorganic chemical vapor deposition. The LED structure of $TiO_2$/QDs/Si showed typical p-n diode currentvoltage and electroluminescence characteristics. The colloidal core-shell CdSe/ZnS QDs were synthesized via pyrolysis in the range of $220-280^{\circ}C$. Pyrolysis conditions were optimized through systematic studies as functions of synthesis temperature, reaction time, and surfactant amount.

• Journal of the Korean Society for Railway
• /
• v.15 no.6
• /
• pp.588-596
• /
• 2012

This paper presents a new semi-analytical annular Mindlin plate element with which out-of-plane natural vibration of thick disks can be analyzed simply, efficiently, and accurately through FEM by including effects of rotary inertia and transverse shear deformation. Using static deformation modes which are exact solutions of equilibrium equations of annular Mindlin plate, the element interpolation functions, stiffness and mass matrices corresponding to each number of nodal diameters are derived. The element is capable of representing out-of-plane rigid-body motions exactly and free from shear locking. Natural frequencies of uniform and multi-step disks with or without concentric ring support are analyzed by applying the presented element. Such results are compared with theoretical predictions of previous works or FEA results obtained by using two-dimensional shell element to investigate the convergence and accuracy of the presented element.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.11
• /
• pp.1190-1198
• /
• 2012

A hot forming of large thick Al plate using a grid-type hybrid die is a process to make a shell plate for the production of a spherical LNG tank. This process is characterized by using a grid-typed die with an additional air cooling system for reducing the cooling time of the heated plate after hot forming. The process consists of the plate's feeding, heating, forming and cooling in detail and each of them is continuously performed along the rail. This paper was designed to propose the analytical and experimental methods for determining the convection and interfacial heat transfer coefficients required in hot forming analysis of Al plate. These values in the analysis are to reproduce numerically the cooling performance of grid-typed die and cooling device. Interfacial heat transfer was obtained from the heat transfer experiments for different pressures and inverse analysis method. To verify the efficiency of the coefficient values obtained from above methods, FE analysis and experiment of the hot spherical-forming process were conducted for a small-scaled model. The convection coefficient was also calculated from flow analysis of air released by cooling device within grid-typed die using ANSYS-CFX.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.3
• /
• pp.307-320
• /
• 2013

This paper proposes a new hybrid support structure by the driven piles which removes disadvantages of the existing type of support structure for offshore wind turbines. The hybrid type of support structure is combined with concrete cone and steel shaft, and is supported not only by gravity type foundations but also by driven piles. For three dimensional analysis of the huge and thick concrete structure, a solid-shell element that is capable of exact modeling and node interpolations of stresses is developed. By applying wave theory of stream function and solid-shell element in XSEA simulation software for fixed offshore wind turbines, a quasi-static analysis and natural frequency analysis of proposed support structure are performed with the environmental condition on Southwest Coast in Korea. In the result, lateral displacement is not exceed allowable displacement and a superiority of dynamic behavior of new hybrid support structure is validated by natural frequency analysis. Consequently, the hybrid support structure presented in this study has a structural stability enough to be applied on real-site condition in Korea. The optimized structures based on the preliminary design concept resulted in an efficient structure, which reasonably reduces fabrication costs.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.1
• /
• pp.54-59
• /
• 1999

High-speed electronic digital computers have enabled engineers to employ various numerical discretization techniques for solutions of complex problems. The Finite Element Method is one of the such technique. The Finite Element Method is one of the numerical analysis based on the concepts of fundamental mathematical approximation. Three dimensional plate structures used often in partition of ship, box girder and frame are analyzed by Finite Element Method. In design of structures, the static deflections, stress concentrations and dynamic deflections must be considered. However, these problem belong to geometrically nonlinear mechanical structure analysis. The analysis of each element is independent, but coupling occurs in assembly process of elements. So, to overcome such a difficulty the shell theory which includes transformation matrix and a fictitious rotational stiffness is taken into account. Also, the Mindlin's theory which is considered the effect of shear deformation is used. The Mindlin's theory is based on assumption that the normal to the midsurface before deformation is "not necessarily normal to the midsurface after deformation", and is more powerful than Kirchoff's theory in thick plate analysis. To ensure that a small number of element can represent a relatively complex form of the type which is liable to occur in real, rather than in academic problem, eight-node quadratic isoparametric elements are used. are used.

• Structural Engineering and Mechanics
• /
• v.43 no.4
• /
• pp.411-437
• /
• 2012

In this paper, we propose a continuum mechanics based 3-D beam finite element with cross-sectional discretization allowing for warping displacements. The beam element is directly derived from the assemblage of 3-D solid elements, and this approach results in inherently advanced modeling capabilities of the beam element. In the beam formulation, warping is fully coupled with bending, shearing, and stretching. Consequently, the proposed beam elements can consider free and constrained warping conditions, eccentricities, curved geometries, varying sections, as well as arbitrary cross-sections (including thin/thick-walled, open/closed, and single/multi-cell cross-sections). We then study the modeling and predictive capabilities of the beam elements in twisting beam problems according to geometries, boundary conditions, and cross-sectional meshes. The results are compared with reference solutions obtained by analytical methods and solid and shell finite element models. Excellent modeling capabilities and solution accuracy of the proposed beam element are observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.690-693
• /
• 2003

Soft x-ray microscopy provides a unique set of capabilities in-between those of visible light and electron microscopy. It has long been recognized that nature provides a 'water window' spectral region between the K shell x-ray absorption edges of carbon (~290eV) and oxygen (~540eV), where organic materials show strong absorption and phase contrast, while water is relatively non-absorbing. This enables imaging of hydrated biological specimens that are several microns thick with high intrinsic contrast using x-rays with a wavelength of 2.3~4.4nm. Soft X-ray microscopy is therefore well suited to the study of specimens like single biological cells. The most direct advantage of X-ray microscope is their high spatial resolution when compared with visible light microscopes, combined with an ability to image hydrated specimens that are several microns with a minimum of preparation. Our study describes the conceptual design of soft x-ray microscope system based on a laser-based source for biomedical application with high resolution ($\leq$50nm) and short exposure time ($\leq$30sec).

• Journal of the Society of Disaster Information
• /
• v.10 no.1
• /
• pp.1-14
• /
• 2014

This paper presents the three-dimensional stress analysis of orthotropic thick plates using the three-dimensional spline strip method based on the theory of elasticity. The orthotropic plates are made of Aragonite crystal and sitka spruce. To demonstrate the convergence and accuracy of the present method, several examples are solved, and results are compared with those obtained by other exact and numerical methods based on the theory of elasticity. Good convergence and accuracy are obtained. The effects of thickness/width ratio, aspect ratio and boundary conditions on normal stress distributions of Aragonite crystal plates and sitka spruce plates are investigated. Moreover, the difference of weak orthotropic and strong orthotropic properties given to the characteristics of stress distributions are also shown.