• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2633-2636
• /
• 2011

A new type of ionic liquid based on N-(3-aminepropyl)imidazolium iodide, called IIQAI, which consists of imidazolium and quaternary ammonium salt, and APII-(hydroxyethyl, propyl, hexyl) were synthesized and used as ionic liquid in dye-sensitized solar cells. APII-hexyl is solid, whereas IIQAI, APII-(hydroxyethyl, propyl) are viscous liquids. The synthesized ionic liquid showed relative thermal stability compared to the commercial ionic liquid of DMII. Among them, IIQAI was more stable than the other ionic liquid because of the two salt groups. APII-hydroxyethyl, which contains two hydroxyl groups, showed low viscosity with good flow. New types of ionic liquids were examined by $^1H$-NMR spectroscopy, thermo gravimetric analysis (TGA). IIQAI enabled a solar energy conversion efficiency of 6.3%, which is slightly higher than that of the referenced (DMII, 6.2%).

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.263-270
• /
• 2011

The aim of this paper is, through the experiment of Lithium-Ammonia solutions $(Li(NH_3)_n)$, to analyze and verify a thermoelectric-conversion property at near Ammonia-boiling point ($-40^{\circ}C$). The experiment results show that the solutions with 0.58 MPM~1.87 MPM generate thermoelectric power at temperature difference $({\Delta}T=0{\sim}15^{\circ}C)$ where Current is constantly proportional to Voltage. This paper provides a new insight into the development of a thermoelectric material.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.6
• /
• pp.44-50
• /
• 2006

To characterize thermo-chemical feature of su gar conversion of woody biomass poplar wood (Populus alba${\times}$glandulosa ) by sub- and supercritical water was treated for 60s under subcritical (23 MPa, 325 and $350^{\circ}C$) and supercritical (23 MPa, 380, 400, and $425^{\circ}C$) conditions, respectively. Among degradation products undegraded poplar wood solids existed in aqueous products. As the treatment temperature increased, the degradation of poplar wood was enhanced and reached up to 83.1% at $425^{\circ}C$. The monomeric sugars derived from fibers of poplar wood by sub- and supercritical treatment were analyzed by high performance anionic exchange chromatography (HPAEC). Under the subcritical temperature ranges, xylan, main hemicellulose component in poplar wood, was preferentially degraded to xylose, while cellulose degradation started at the transition zone between sub and supercritical conditions and was remarkably accelerated at the supercritical condition. The highest yield of monomeric sugars amounts to ca. 7.3% based on air dried wood weight (MC 10%) at $425^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.102.1-102.1
• /
• 2010

바이오매스(Biomass)는 지구상에서 에너지원으로 이용될 수 있는 모든 식물과 미생물을 총칭하는 의미로 사용된다. 최근 바이오매스를 에너지자원화 시키는 방법으로 주목받는 열화학적 전환(Thermo-chemical conversion) 반응은 산소가 없이 혹은 희박한 조건에서 바이오매스에 열과 압력을 가하거나 공기나 수증기 등의 가스화제와 반응하여 바이오오일(Bio-oil) 및 합성가스(Syngas)로 변화하는 프로세스를 의미한다. 바이오매스로부터 바이오 DME(Di-Methyl Ether) 생산을 위한 합성가스를 제조하기 위해서 국내 산림자원을 대상으로 열분해반응 특성연구를 수행하였다. 또한 이들 물질로부터 바이오 DME 합성을 위해 최적의 합성가스 제조를 위한 타당성 연구를 수행하였다. 반응온도 $800{\sim}900^{\circ}C$에서 가스화 수율은 78~80%, 촤 수율은 17~20%, 타르 수율은 4~10%였고, 합성가스($H_2$/CO)비는 0.9~1.6였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.443-446
• /
• 2009

바이오매스 에너지라 함은 생물체를 구성하는 유기물을 이용하는 에너지이다. 바이오매스는 에너지 위기 및 $CO_2$에 의한 지구온난화 및 화석자원의 고갈이 진행되면서, 화석연료와 달리 재생이 가능하고 지속 가능한 자원으로 각광을 받고 있다. 그 중에서도 목질계 바이오매스는 다른 신재생에너지원에 비해 국내 잠재량이 가장 풍부한 에너지원 중의 하나이다. 바이오매스 에너지 기술로는 직접연소, 열화학적 변환, 생화학적 변환의 기술이 있다. 본 연구에서는 목재를 원료로 한 부분산화 조건의 숯 생산 공정에서 목재의 열분해 가스 생산특성을 고찰하였다. 열분해가스 중에 응축된 목초액의 pH는 3.58～3.92 정도로 분석 되었고, 산도는 시간이 경과 할수록 2.74에서 4.44%로 농도가 증가 되었다. 숯 생산 공정에서의 목재의 열분해는 초기부터 48시간까지는 열분해가스의 조성의 변화가 거의 없었고, 48시간 경과 후에는 열분해가스 중에 가연성가스인 $H_2$, CO, $CH_4$가 약 5%정도 배출되는 것을 알 수 있었다.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.3-13
• /
• 2004

The use of biomass has attracted extensive attention from the beginning of civilization. However, intensive researches on the biomass from the view point of the development of alternative energy have been carried out just recently. Fast pyrolysis, as a tool for the utilization of the biomass as the secondary energy source has drawn great attentions due to high applicability for the production of several valuable materials from biomass. This review paper focuses on the recent developments of pyrolysis process and reports the characteristics of bio-oil, which is the main product of fast pyrolysis of biomass.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.267-273
• /
• 2012

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber-the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam-was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.80-86
• /
• 2011

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber - the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam - was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.720-726
• /
• 2014

PEM fuel cell vehicles have been getting much attraction due to a sort of highly clean and effective transportation. The onboard fuel processor, however, is inevitably required to supply the hydrogen by conversion from some fuels since there are not enough available hydrogen stations nearby. A lot of studies have been focused on analyses of ATR reactor under the assumption of thermo-neutral condition and those of the optimized process for the minimization of energy consumption using thermal efficiency as an objective function, which doesn't guarantee the maximum hydrogen production. In this study, the analysis of optimization for 100 kW PEMFC onboard fuel processor was conducted targeting various fuels such as gasoline, LPG, diesel using newly defined hydrogen efficiency and keeping simply synthesized heat exchanger network regardless of external utilities leading to compactness and integration. Optimal result of gasoline case shows 9.43% reduction compared to previous study, which shows the newly defined objective function leads to better performance than thermal efficiency in terms of hydrogen production. The sensitivity analysis was also done for hydrogen efficiency, heat recovery of each heat exchanger, and the cost of each fuel. Finally, LPG was estimated as the most economical fuel in Korean market.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.453-460
• /
• 2015

Engineering the polylactide via stereocomplexation with supercritical fluid (SCF) technology paved way to fabricate polymers with enhanced thermal and mechanical properties. We aimed to establish a SCF medium with excellent solubility for PLA without any additional solvent/co-solvent. We, therefore, employed supercritical dimethyl ether to synthesize 100% stereocomplex polylactide from high molecular weight homopolymers with an excellent yield. The remarkable solubility of the homopolymers in dimethyl ether is the key for quick conversion to s-PLA. This study proves a rapid synthesis route of dry s-PLA powder with sc-DME at 250 bar, $70^{\circ}C$ and 1.5 h, which are reasonably achievable processing parameters compared to the conventional methods. The degree of stereocomplexation was evaluated under the effect of pressures, temperatures, times, homopolymer-concentrations and molecular weights. An increment in the degree of stereocomplexation was observed with increased temperature and pressure. Complete conversion to s-PLA was obtained for PLLA and PDLA with $M_n{\sim}200kg{\cdot}mol^{-1}$ with a total homopolymer to total DME ratio of 6:100% w/w at prescribed reaction conditions. The degree of stereocomplexation was determined by DSC and confirmed by XRD. Considerable improvement in thermo-mechanical properties of s-PLA was observed. DSC and TGA analyses proved a $50^{\circ}C$ enhancement in melting transition and a high onset temperature for thermal degradation of s-PLA respectively.