• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.867-871
• /
• 2001

The main reason for reviewing the condensate water return system in the auxiliary steam system is to obtain the thermal high efficiency of the power plant and thus save the fossil energy in power plant. This study intends to analyze the thermal efficiency of the power plant and predict the increasing in the generator output by the return system reformation of auxiliary steam line in the thermal power plant.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.625-630
• /
• 1987

Thermal evaporated SiO rf sputtered SiO2 thin films were most widely used to the gate oxide of TFTs. In this paper, the difference of trap density and distribution between SiO2 and SiO2 film were studied. TFTs using SiO and SiO2 thin film for the gate oxide were fabricated. The output characteirstics of TFTs and the time dpendencd of the leakage current were measured. Models of the carrier transport and carrier trapping in TFT were proposed. The trap density was obtained by substituting measured value for the equation derived from the proposed model. It was found that rf sputtered SiO2 had more traps at interface than thermal evaporated SiO.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.73-75
• /
• 1999

The time harmonics of an inverter output voltage cause high frequency currents in the rotor bars of a squirrel cage induction motor, so that the harmonic copper loss density increases in the upper lesion of the bars. Such an higher loss density makes an nonuniform thermal source and deforms the bars due to the thermal stress. Therefore, in this paper, the copper loss distribution in the rotor bar of an inverter-fed induction motor, which is the source of the thermal stress, is analyzed by the time-stepping finite element method. As a result, the harmonic copper losses of 11 subregions in a bar are calculated and compared with those of sinusoidally fed induction motor.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.919-921
• /
• 1995

In this paper, development of Thermal Printer Head(TPH) controller by using gate array having high reliability and good performance is proposed. Over the 3000 gates are performed to control print image data signals and relative peripheral hardwares. The proposed gate array has TPH control circuit, print control and step motor drive, and print image data control, decoder output control parts. This TPH controller will be a good application to FAX or label printer and barcode printers.

• KIEE International Transaction on Systems and Control
• /
• v.2D no.2
• /
• pp.78-91
• /
• 2002

In the thermal power plant, there are six manipulated variables: main steam flow, feedwater flow, fuel flow, air flow, spray flow, and gas recirculation flow. There are five controlled variables: generator output, main steam pressure, main steam temperature, exhaust gas density, and reheater steam temperature. Therefore, the thermal power plant control system is a multinput and output system. In the control system, the main steam temperature is typically regulated by the fuel flow rate and the spray flow rate, and the reheater steam temperature is regulated by the gas recirculation flow rate. However, strict control of the steam temperature must be maintained to avoid thermal stress. Maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature versus changes in fuel flow rate, difficulty of control of the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, and the fluctuation of inner fluid water and steam flow rates during the load-following operation. Up to the present time, the Proportional-Integral-Derivative Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. This paper focuses on the characteristic comparison of the PID controller and the modified 2-DOF PID Controller (Two-Degrees-Freedom Proportional-Integral-Derivative) on the DCS (Distributed Control System). The method is to design an optimal controller that can be operated on the thermal generating plant in Seoul, Korea. The modified 2-DOF PID controller is designed to enable parameters to fit into the thermal plant during disturbances. To attain an optimal control method, transfer function and operating data from start-up, running, and stop procedures of the thermal plant have been acquired. Through this research, the stable range of a 2-DOF parameter for only this system could be found for the start-up procedure and this parameter could be used for the tuning problem. Also, this paper addressed whether an intelligent tuning method based on immune network algorithms can be used effectively in tuning these controllers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.96-101
• /
• 2005

Cogeneration is an energy conversion process, where electricity and useful heat are produced simultaneously in one process. Also, carbon dioxide emissions can be reduced as well. The cogeneration process may be based on the use of steam, gas turbines or combustion engines. However, there have been few models with an output of less than 100 kilowatt. In the present study, a spark ignited gas engine with generation output of 10 kilowatts was developed for micro cogeneration package. The gas engine shows 29.2$\%$ of thermal efficiency under Stoichiometric combustion and 33.6$\%$ of thermal efficiency under lean combustion. NOx emission shows less than 10ppm at 13$\%$ oxygen under stoichiometric combustion and about 100ppm at 13$\%$ oxygen under lean combustion.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.4 s.13
• /
• pp.28-36
• /
• 2001

Performance analysis is conducted on an axial-type turbine which is used for fire extinction by injecting water or steam into the turbine. Loss models developed by Hacker and Okapuu are applied for predicting the performance of turbine. Pressure loss generated through a turbine is converted to the thermal efficiency, and thermal and gas properties are calculated within a turbine passage. Total-to-total efficiency, total-to-static efficiency, static temperature at the exit of turbine, output power, flow coefficient, blade loading coefficient, and expansion ratio are predicted with changing the amount of injected steam and the rotational speed. The 74 kW class gas turbine developed at KIMM is chosen for performance analysis. The 74 kW class turbine consists of 1 stage like a current developing gas turbine for fire extinction. Water or steam is injected at the end of combustor, and results show that efficiency and output power are dependent on the temperature of injected water or steam and the static temperature at the exit is decreased.

• Nuclear Engineering and Technology
• /
• v.48 no.3
• /
• pp.684-701
• /
• 2016

The Gaussian process model (GPM) is a flexible surrogate model that can be used for nonparametric regression for multivariate problems. A unique feature of the GPM is that a prediction variance is automatically provided with the regression function. In this paper, we estimate the safety margin of a nuclear power plant by performing regression on the output of best-estimate simulations of a large-break loss-of-coolant accident with sampling of safety system configuration, sequence timing, technical specifications, and thermal hydraulic parameter uncertainties. The key aspect of our approach is that the GPM regression is only performed on the dominant input variables, the safety injection flow rate and the delay time for AC powered pumps to start representing sequence timing uncertainty, providing a predictive model for the peak clad temperature during a reflood phase. Other uncertainties are interpreted as contributors to the measurement noise of the code output and are implicitly treated in the GPM in the noise variance term, providing local uncertainty bounds for the peak clad temperature. We discuss the applicability of the foregoing method to reduce the use of conservative assumptions in best estimate plus uncertainty (BEPU) and Level 1 probabilistic safety assessment (PSA) success criteria definitions while dealing with a large number of uncertainties.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.12
• /
• pp.82-90
• /
• 2019

This analysis demonstrates the effective removal of heat generated from a solar panel's output degradation factor solar cells (the solar panel's output deterioration factor), and solves the problems of oxidation and corrosion in existing metal heat sinks. The heat-dissipating test specimen was prepared using carbon materials; then, its thermal conductivity and its effectiveness in reducing temperatures were studied using heat transfer numerical analysis. As a result, the test specimen of the 30g/㎡ basis weight containing 80% of carbon fiber impregnated with carbon ink showed the highest thermal conductivity 6.96 W/(m K). This is because the surface that directly contacted the solar panel had almost no pores, and the conduction of heat to the panels appeared to be active. In addition, a large surface area was exposed to the atmosphere, which is considered advantageous in heat dissipation. Finally, numerical analysis confirmed the temperature reduction effectiveness of 2.18℃ in a solar panel and 1.08℃ in a solar cell, depending on the application of heat dissipating materials.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.12
• /
• pp.1383-1390
• /
• 2007

In this paper, we study an optical add-drop multiplexer which consists of the fiber Bragg grating filter and investigate the temperature characteristics of it. To resolve the characteristics, we find and analyze numerically its temperature response, and fabricate an optical add/drop multiplexer and measure its output spectrum. From the obtained results, they show that the center wavelength of output spectrum shifts approximately 0.01230 nm/$^{\circ}C$ within a temperature range $-30{\sim}90^{\circ}C$.