• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.229-239
• /
• 2010

Performing a series of in-situ thermal response tests, the effective thermal conductivity of six vertical closed-loop ground heat exchangers was experimentally evaluated and compared each other, which were constructed in a test bed in Wonju. To compare thermal efficiency of the ground heat exchangers in field, the six boreholes were constructed with different construction conditions: grouting materials (cement vs. bentonite), different additives (silica sand vs. graphite) and the shape of pipe-sections (general U-loop type vs. 3 pipe-type). From the test results, it can be concluded that cement grouting has a higher effective thermal conductivity than that of bentonite grouting, and the efficiency of graphite better performs over silica sand as a thermally-enhancing addictive. In addition, a new 3 pipe-type heat exchanger provides less thermal interference between the inlet and outlet pipe than the conventional U-loop type heat exchanger, which results in superior thermal performance.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.697-700
• /
• 2005

Aquifer Thermal Energy Storage (ATES) system can be very cost-effective and renewable energy sources, depending on site-specific parameters and load characteristics. In order to develop an ATES system which has certain hydrogeological characteristics, understanding of the thermo hydraulic processes of an aquifer is necessary for a proper design of an aquifer heat storage system under given conditions. The thermo hydraulic transfer for heat storage is simulated using FEFLOW according to two sets of pumping and waste water reinjection scenarios of heat pump operation in a two layered confined aquifer. In the first set of model, the movement of the thermal front and groundwater level are simulated by changing the locations of injection and pumping well in seasonal cycle. However, in the second set of model the simulation is performed in the state of fixing the locations of pumping and injection well. After 365 days simulation period, the temperature distribution is dominated by injected water temperature and the distance from injection well. The small temperature change is appears on the surface compared to other slices of depth because the first layer has very low porosity and the transfer of thermal energy are sensitive at the porosity of each layer. The groundwater levels and temperature changes in injection and pumping wells are monitored to validate the effectiveness of the used heat pump operation method and the thermal interference between wells is analyzed.

• New & Renewable Energy
• /
• v.2 no.1 s.5
• /
• pp.56-65
• /
• 2006

The thermal performance of glass evacuated tube solar collectors are numerically and experimentally investigated. Four different shapes of solar collectors are considered and the performances of these solar collectors are compared. Dealing with a single collector tube, the effects of not only the shapes of the absorber tube but also the incidence angle of solar irradiation (beam irradiation) on thermal performance of the collector are studied. However, the solar irradiation consists of the beam irradiation as well as the diffuse irradiation. Also, the interference of solar irradiation and heat transfer interaction between the tubes exist in an actual solar collector, These effects are considered in this study experimentally and numerically. The accuracy of the numerical model is verified by the experimental results. The result shows that the thermal performance of the absorber used a plate fin and U-tube is the best.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.3
• /
• pp.63-66
• /
• 2014

In this study, we investigated the effects of Cu TSV on the thermal management of 3D stacked IC. Combination of backside point-heating and IR microscopic measurement of the front-side temperature showed evolution of hot spots in thin Si wafers, implying 3D stacked IC is vulnerable to thermal interference between stacked layers. Cu TSV was found to be an effective heat path, resulting in larger high temperature area in TSV wafer than bare Si wafer, and could be used as an efficient thermal via in the thermal management of 3D stacked IC.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1370-1375
• /
• 2004

This article investigates the heat transfer characteristics in a RTA system for LCD manufacturing and suggests a way to evaluate the quality of a poly-Si film from the thin film optics analysis. The transient and one-dimensional conductive/radiative heat transfer equation considering wave interference effect is solved to predict surface temperatures of thin films. In dealing with radiative heat transfer, a one-dimensional two-flux method is used and the ray tracing method is also utilized to account for the wave interference effects. It is assumed that each interface is assumed diffusive but the spectral radiative properties are included. It is found that the selective heating region exists for various wavelengths and consequently may contribute to heat the poly-Si film. Using the formalism of the characteristic transmission matrix, the lumped structure reflectance, transmittance, and absorptance are calculated and they are compared with experimental data of the poly-Si film during the SPC process via the FE-RTA (Field-Enhanced RTA) technology.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.5
• /
• pp.1-9
• /
• 1994

In this paper, we analyzed the performances for FH/CPFSK system with limiter-discriminator detection and integrate-and-dump post-detection filtering under thermal noise and partial-band jamming noise. And,we considered intersymbol interference-related SNR and differential phase parameters for all eight of the possible adjacent bit data patterns, FM noise clicks for evaluating FH/CPFSK and CPFSK Systems. In result, the optimum modulation index h was 0.7 and the optimum value of bandwidth-time product D was 1.0 Next, when we considered the thermal noise under the partial-band jamming, the thermal noise significantly influenced the error probability of system below 20dB approximately but could ignore above 20dB.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.42-51
• /
• 1996

Performance analysis of FH/CPFSK system with liiter-discriminator detection and integrate-dump post-detection filtering under the thermal noise and the partial-band noise jamming on the rayleigh fading channel have been analyzed. The thermal noise and partial-band noise jamming, rayleigh fading, intersymbol interference for all eight of the possible adjacent bit data patterns, and FM noise click for evaluating systems have been considered. Also optimum parameters to improve performance of FH/CPFSK system have been obtained and validities for AMPS and CDMA system of land-mobile-communication system through computer simulation have been proved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.7
• /
• pp.1787-1802
• /
• 1996

In this paper, the performance for FH/CPFSK system with limiter-discriminator detection and integrage-and-dump post-detection filtering under thermal noie, partial-band noise jamming and rayleigh fading have been analyzed. The method of hard-decision diversity of which the transmitter repeated L times on different hops for each data symbol in a way to mutigate the effects of the jamming has been applied, and the receiver has been combined the L chips. Also, error-correcting code have been applied for improving performance of system. The thermal noise and partial-band noise jamming, intersymbol interference for all eight of the possible adjacent bit data patterns, and FM noise click for evaluating systems have been considered. Also optimum parameters to improve performance of FH/CPFSK system have been obtained and validities have been proved through computer simulation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.2
• /
• pp.67-74
• /
• 2015

In this study, analysis and experiments were carried out on temperature distributions and thermal deformations in a dry vacuum pump with vertical screws for safe operation. When a vacuum pump is working, it is necessary to get rid of the heat generated by the friction of bearings and the compression of air to prevent the vacuum pump from being damaged by interference between two screws and housing through thermal deformation. Additional cooling was proposed by using oil flow through the inner channel of the rotating axis for lower temperature control of the vacuum pump. Analysis and experimental results were compared in terms of temperature distribution and thermal deformation of the vacuum pump, and two sets of results matched reasonably well. These results for a dry vacuum pump with vertical screws can be used in similar model development and can minimize errors in design and manufacture by providing reasonably accurate prediction in advance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.7
• /
• pp.659-668
• /
• 2005

The thermal performances of glass evacuated tube solar collectors are numerically investigated. Four different shapes of solar collectors are considered and the performances of these solar collectors are numerically investigated. Dealing with only collecting tube, the effects of not only the shape of the absorber tube but also the incidence angle of solar irradiation on the thermal performance of the collector are studied because the energy obtained by the absorber can be varied according to the incidence angle of solar radiation. However, the solar irradiation consists of the beam radiation as well as the diffuse radiation. Also, in actual system, the interference of solar irradiation and heat transfer interaction between the tubes should be considered. Therefore, this study considered these effects is carried out experimentally and numerically. The accuracy of the numerical model is verified by experiments. The result shows that the thermal performance of the absorber used a plate fin and U-tube is about $25\%$ better than those of the other models.