• 대한기계학회논문집A
• /
• 제21권10호
• /
• pp.1541-1550
• /
• 1997

Since the ceramic/metal joint material is made at a high temperature, the residual stress develops when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of Si$_3$N$_4$STS304 joints quantitatively and to compare the strength of joints. The difference of residual stress is measured when repeated thermal cycl is loaded, under the conditions of the practical use of the ceramic/metal joint. The residual stress increases at 1 cycle of thermal load but decreases in 3 cycles to 10 cycles of thermal load. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a result, it is known that the stress of joint decreases as the number of thermal cycle increases.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권6호
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.13-16
• /
• 2005

Generally, as corrosive protection processing of a steel structure, zinc galvanizing and heavy duty coating paint are applied. However, zinc galvanizing has the difficulty of restriction of a size, or on-site construction. Moreover, heavy duty coating paint has a problem with many administrative and maintenance expenses with short problem of adhesion, corrosion generating of a damage portion, and maintenance management cycle. In this study, a salt water spray test, CASS test, and the electrochemistry examination were carried out for the thermal metal spray method of construction for corrosive protection performance evaluation. Moreover, the corrosive protection life of a thermal metal spray method of construction was quantitatively calculated on the basis of this experiment. in consideration of LCC, the economical efficiency of a general corrosive protection method of construction and a thermal metal corrosive protection method of construction was compared. Consequently, although initial construction expense was estimated 16 to $30\%$ high, as for a thermal metal spray method of construction, it turns out that the administrative and maintenance expenses for 100 years became cheap 9.3 to 13 or more times.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.22-29
• /
• 2020

In nuclear power plants, there is a risk of thermal fatigue in equipment and piping affecting system soundness because the temperature change of the system accompanies in every operation and shutdown. Therefore, in order to prevent the excess of the fatigue limit during the lifetime of plants, the fatigue limit of each piping material is determined in the designing stage. However, there are many cases where equipment or piping is locally subjected to thermal fatigue that is not considered in the design, resulting in damage to the equipment and piping, and failure during operation. Currently, local thermal fatigue generation mechanisms that are not taken into account in the design stage are gradually being identified. In this paper, the effects of the fluid temperature fluctuations on the piping soundness due to the mixing of hot and cold water, one of the local thermal fatigue generating mechanisms, were evaluated.

• 한국수소및신에너지학회논문집
• /
• 제15권1호
• /
• pp.32-38
• /
• 2004

Thermal behaviors of $(Cu_{0.5}Mn_{0.5})Fe_2O_4$, prepared by a solid method, were investigated for $H_2$ production by a thermochemical cycle. The thermal reduction of $(Cu_{0.5}Mn_{0.5})Fe_2O_4$ started from $300^\circ{C}$ and the weight loss was 1.3 wt% up to 1200. XRD shows the prepared ferrite has the spinel structure with a lattice constant of $8.414{\AA}$ and changed to the oxygen deficient structure by thermal reduction. Oxygen and hydrogen can be separately produced by the cycles of thermal reduction and water oxidation of the oxygen deficient ferrite.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.92-97
• /
• 1998

Because of the low melting temperature of solder, each temperature cycle initiates an irrecoverable creep deformation at the solder interconnection which connects the package body with the PCB. The crack starts and propagates from the position where the creep deformation is maximized. This work has tried to compare and analyze the thermal fatigue life of solder interconnection which is affected by the lead material, the size of die pad, chip thickness, and interface delamination of 48-Pin TSOP under the temperature cycle ($0^{\circ}C$~1$25^{\circ}C$). The crack initiation position and thermal fatigue life which are calculated by using FEA method are well matched with the results of experiments. The thermal Fatigue life of copper lead frame is extended around 3.6 times longer than that of alloy 42 lead frame. It is maximized when the chip size is matched with the length of the lead. It tends to be extended as the thickness of chip got thinner. As the interfacial delamination between die pad and EMC is increased, the thermal fatigue life tends to decrease in the beginning of delamination, and increase after the delamination grew after 45% of the length of die pad.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.117-121
• /
• 2003

In order to investigate the performance characters of the ramjet propulsion, at the first step, in this paper Ideal Brayton cycle is adopted. In the Ideal Ramjet cycle some of the Parameters are independent of the heat input, for example thermal efficiency but in the Ideal Brayton cycle, Mach number and the entry temperature of the combustion chamber are important variables with the heat input.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권8호
• /
• pp.1009-1015
• /
• 2011

본 연구에서는 고팽창사이클의 경우 가변밸브시스템을 구성하여 흡기밸브 닫힘시기를 늦추는 방식으로 실현하였고, 저압축에 따른 흡입공기의 감소는 과급압력으로 해결하였다. 이와 같이 디젤기관에 아트킨슨사이클을 실현하여 엔진의 열효율향상 가능성을 알아보았다. 그 결과 흡기밸브 닫힘시기 ABDC $40^{\circ}$ 부터 ABDC $80^{\circ}$ 까지 전 영역에 걸쳐 열효율 및 출력의 향상이 있었다. 다만, 흡기밸브 닫힘시기가 ABDC $70^{\circ}$이후로는 열효율 증가 폭이 둔화되는 경향을 보였다. 위와 같은 연구결과 저속 디젤-아트킨슨사이클화의 최적 연소조건은 흡기밸브 닫힘시기가 ABDC $70^{\circ}$전후로 보이며, 고부하영역이 저부하영역보다 더 효과적으로 나타났고, 중부하영역에서 기관운전은 안정적이었다. 이때 정미열효율은 통상의 디젤기관보다 평균 약 12.5% 높게 나타났다.

• Nuclear Engineering and Technology
• /
• 제35권6호
• /
• pp.529-536
• /
• 2003

The objective of this study is to investigate the reorientation of hydrides with applied stress intensity factor, the peak temperature and the time when to apply the stress intensity factor in a Zr-2.5Nb pressure tube during its thermal cycle treatment. Cantilever beam (CB) specimens with a notch of 0.5 mm in depth made from the Zr-2.5Nb tube were subjected to electrolytic hydrogen charging to contain 60 ppm H and then to a thermal cycle involving heating to the peak temperature of either 310 or $380^{\circ}C$, holding there for 50 h and then cooling to the test temperature of $250^{\circ}C$. The stress intensity factor of either 6.13 or $18.4\;MPa\sqrt{m}$ was applied at the beginning of the thermal cycle, at the end of the hold at the peak temperatures and after cooling to the test temperature, respectively. The reorientation of hydrides in the Zr-2.5Nb tube was enhanced with the increased peak temperature and applied stress intensity factor. Furthermore, when the CB specimens were subjected to $18.4\;MPa\sqrt{m}$ from the beginning of the thermal cycle, the reoriented hydrides occurred almost all over the Zr-2.5Nb tube, surprisingly suppressing the growth of a DHC crack. In contrast, when the CB specimens were subjected to the stress intensity factor at the test temperature, little reorientation of hydrides was observed except the notch region, leading the Zr-2.5Nb to grow a large DHC crack. Based on the correlation between the reorientation of hydrides and the DHC crack growth, a governing factor for DHC is discussed along with the feasibility of the Kim's DHC model.

• Nuclear Engineering and Technology
• /
• 제23권1호
• /
• pp.56-65
• /
• 1991

RELAP5/MOD2 Cycle 36.04코드를 이용하여 LOFT대형냉각재 상실사고 모사실험 L2-3를 계산함으로써 코드의 대형냉각재상실사고에 관련된 열수력현상 예측능력을 평가하였다. 기본계산에서 원자로 압력용기는 이중노심유로와 분리강수관 모델로 모사되었다. 기본계산의 결과 계통의 전반적인 수력학적 거동과 감압기간동안 노심 고출력 부위에서의 열적 거동은 비교적 타당하게 예측되었다. 한편 과냉각-이상유동의 천이 기간동안 임계유량모델, 고질량유속에서의 임계열유속 상관식, 감압기간중의 재접수(Blowdown Rewet)의 판정기준등 코드의 모델/상관식의 부분적 결함이 발견되었다. 이 결함들에 의해 냉각재 재고량이 과대 평가되어 재환수기간의 노심의 열적거동 예측의 정확도가 감소되었다. RELAP5/MOD2 Cycle 36.04로 부터 개선된 코드를 사용한 계산 결과 재접수 현상의 예측 정확도를 개선할 수 있었다.