• Journal of the Korea Institute of Building Construction
• /
• v.15 no.5
• /
• pp.465-471
• /
• 2015

This study proposed V-shaped tie bar method as an alternative of internal cross-tie for reinforced concrete columns in order to enhance the constructability and confinement effectiveness of the lateral tie bars. A total of 35 pull-out specimens were prepared with the parameters of concrete compressive strength and bending angle and embedment length of the V-shaped bar to examine the bond stress-slip relationship of the V-shaped tie bar. The bond strength of the V-shaped tie bars with the bending angle not exceeding $60^{\circ}$ was higher than the predictions obtained from the equations of CEB-FIP provision. Considering the constructability and bond behavior of the V-shpaed tie bar, the bending angle and embedment length of such bar can be optimally recommended as $45^{\circ}$ and 6db, respectively, where db is the diameter of the tie bar.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.6
• /
• pp.381-388
• /
• 2018

A novel and simple algorithm for accurate calculation of RMS voltage is proposed in a digitally controlled grid-tie inverter system. Given that the actual frequency of grid voltage is continuously changing, the constant sampling frequency cannot be a multiple number of the fundamental frequency. Therefore, the RMS of grid voltage contains periodic oscillations due to the differences in the phase angle of sampled data during calculation. The proposed algorithm precisely calculates and updates the initial phase angle of the first sampled voltage in a half-cycle period using phase-locked loop, which is commonly utilized for phase angle detection in grid-tie inverter systems. The accuracy and dynamic performance of the proposed algorithm are compared with those of other algorithms through various simulations and experiments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.9-15
• /
• 2016

Distribution networks are operated in radial fashion during the normal state. Loop configuration is also required temporally in case of live load transfer among the adjacent feeders. Voltage angles of each substation buses are very important data in order to calculate power flow of the loop structured distribution feeders. This paper proposes substation bus voltage angle calculation method using voltage angle difference measured at the normally open tie switches. Simulation case studies using Matlab simulink have been performed to establish feasibility of proposed method.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.6
• /
• pp.697-706
• /
• 2006

Tower crane's wall tie is generally used for extending of mast height according to rising of lifting height. In order to get wall tie member force this problem, this study concerning wall tie is based on load data described in manual book of 290HC model. This study made the equation of wall tie member force and computer programming for calculating wall tie member force and then get ${\theta}-P$ curves(angle-wall tie force). After considering the ${\theta}-P$ curves, optimum angle range ($48.4^{\circ}{\sim}77.2^{\circ}$) about wall ties (A), (C) members was obtained. Member force of wall tie (B) was changed from tension to compression or from compression to tension at $74^{\circ}$ in service and $54^{\circ}$ in out of service. When both horizontal force($H_A$) and torsional moment ($M_D$) were varied from (+) to (-), wall tie force(A, B, C) were changed almost symmetrically about ${\theta}$-axis. Because this study was based on wall tie analysis conditions, wall tie members in symmetric and ideal geometry shape used for analizing wall tie of tower crane, it is necessary to have more careful verification in order to apply generally the results of this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4095-4100
• /
• 2011

In this paper, a log periodic bow-tie dipole array (LPBDA) antenna for UWB communications is investigated. Bow-tie shaped dipole elements are used instead of general dipole elements for LPDA antennas and the input reflection coefficient and realized gain characteristics of the LPBDA as a function of a flare angle are analyzed. It turns out that as the flare angle of the bow-tie dipole elements is increased, the lowest operating frequency is shifted toward lower frequency and the operating frequency band is increased, but the average gain is decreased. However, the gain variation of the LPBDA is much decreased and the front-back ratio is improved compared to the LPDA. Standard LPDA and LPBDA with a flare angle of 13 degrees are fabricated on an FR4 substrate with a dielectric constant of 4.4 and a thickness of 1.6 mm. Measured gain for the LPDA ranges from 4 to 6.5 dBi at 3.1 to 10.6 GHz band, while that for the LPBDA is in the range of 4.2 to 5 dBi.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2162-2167
• /
• 2014

Robots are widely used in various automation processes in industrial applications. Traditionally, it operated under fixed condition by teaching operating positions. Recently, diverse 2D/3D sensors are used together with robot to give more flexibility in operation. In this paper, we deal with automatic manipulation of tie rod in automotive production line. Sensor system consisted of a camera and slit laser is used for the acquisition of 3D information and it is used attached on the robot. Nut runner is used for the manipulation of stop nut and adjust bolt on the tie rod. Detailed procedures for the automatic manipulation of tie rod are presented. In the presented approach, we effectively use 3D information in whole procedure such as computing distance to the tie rod, rotation angle of bolt and nut. Experimental results show the feasibility of the proposed algorithm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1445-1450
• /
• 2013

In this paper, a broadband series-fed bow-tie dipole pair (SBDP) antenna operating in the band of 1.7-2.7 GHz for mobile communication base station applications is proposed. The proposed antenna uses bow-tie-shaped dipole elements instead of straight strip dipole ones used in a conventional series-fed dipole pair (SDP) antenna. The simulation results show that the lowest operating frequency is shifted toward lower frequency as the flare angle increases, and so the lengths of the bow-tie dipole elements can be reduced in proportion to the frequency shift toward lower frequency. An SBDP antenna with a flare angle of 10 degrees is fabricated on an FR4 substrate (dielectric constant = 4.4 and thickness = 1.6 mm) and total width of the fabricated antenna is reduced by 10% compared to that of the conventional SDP antenna. The measured impedance bandwidth for voltage standing wave ratio (VSWR) < 2 is 48.8% (1.69-2.78 GHz), gain is 5.8-6.3 dBi, and the front-to-back ratio (FBR) is 14-17 dB.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.3
• /
• pp.105-109
• /
• 2011

Critical angle of quartz (R.I. ${\fallingdotseq}$ 1.553) and diamond (R.I. = 2.417) are $40.09^{\circ}$ and $24.26^{\circ}$ that calculated by $sin{\theta}=r_2/r_1$ (r = refractive index, $r_1$ > $r_2$). Brilliance of quartz and diamond are 20.33% and 55.07%. The brilliance data are result of study on the incident light internal round brilliant cut quartz and diamond by the critical angle. Cause of bow-tie phenomenon can be studied by application of critical angle theory and light path inside fancy shape brilliant cut. When refractormetry with typical gem refractometer, critical angle of quartz and corundum are $59.1^{\circ}$ and $77.9^{\circ}$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.7
• /
• pp.14-21
• /
• 2015

Distribution systems are operated in radial structure, but temporal loop structure could be founded the live load transfer. Main purposes of reconfiguration of distribution network are load balancing, loss minimization and voltage drop maintaining. In the loop structure, huge loop current can be flowed between two substations in case of large voltage angle difference. Protection devices of distribution line can be triped by this huge loop current. So, precise calculation of loop current is very important for secure switching. This paper proposes a novel calculation method of loop current using the voltage angle differences measured at the tie switches. Feasibility of the propose method has been verified by various case studies based on Matlab simulation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.166-168
• /
• 2007

스퍼터링법으로 제작된 FCCL은 PI필름(Poly-imide film)과 Cu layer사이에 Tie-coating layer로 Ni-Cr을 많이 사용한다. 하지만 완성된 FCCL에서 페터닝을 실시할 때 Cr성분이 소멸되지 않고 잔존하는 현상으로 누설전류가 발생 한다. 또한 Cr으로 인해 Eatching액의 오염으로 재사용의 어려움도 발생된다. 이러한 원인들은 제품의 특성들을 저하 시키므로 이를 개선할 필요가 있다. 따라서 본 연구에서는 기존의 Tie-coating layer를 대체할 물질로 Acrylic acid를 이용하여 FCCL을 제작하여 표면특성 평가를 위해 Contact angle측정과 부착력을 위한 Peel test측정과 조직분석 및 성분분석을 위해 SEM-EDS를 측정을 통하여 Polymerization을 이용한 Ti-coating layer 개발의 가능성을 확인하였다.