• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.277-278
• /
• 2002

Magnetron and Ion beam sputtering were used to texture the air-bearing surface of magnetic recording sliders. Flying height measurements and Laser-Doppler interferometry were used to compare the 'flyability' of textured and untextured sliders. Lubricant redistribution on the disk surface caused by slider/disk interactions was investigated using scanning ellipsometry (Surface Reflectance Analyzer (SRA)). The results show that slider surface texture causes only small changes in the flying height of sliders but reduces slider in-plane and out-of-plane vibrations. Textured sliders were found to cause less lubricant depletion on the disk surface than untextured sliders.

• Textile Coloration and Finishing
• /
• v.20 no.2
• /
• pp.47-52
• /
• 2008

Nylon textured yarn is usually manufactured by disk type false twist texturing. Dyeing properties of nylon textured yam have not been studied yet. In this study, dyeing properties of nylon textured yam according to draw ratio out of process parameters were investigated. The fact that microstructure of nylon textured yarn in amorphous region particularly is transformed by draw ratio was confirmed indirectly by measurement of dyeing rate because dyeing rate was affected by the structure of amorphous region. Dyeing rate at draw ratio 1.29 was the lowest because the higher draw ratio increase amorphous orientation and disturb dye diffusion into amorphous region. The microstructure according draw ratio was indirectly confirmed by 5% strength, tenacity, elongation. But difference in K/S value and fastness was insignificant.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.395-402
• /
• 2000

The effect of particulate contamination on friction and wear between a negative-pressure picoslider and a laser-textured disk was studied. Particles of different concentrations, materials and sizes were injected to the head-disk interface (HDI), consisting of disks with various textures, at the same speed. In a contaminated environment, durability of head-disk interface gradually decreased as the particle concentration increased. Large particles caused HDI failure early and resulted in an extensive damage to the slider and disk surfaces. Hard particles also caused HDI failure earlier and damages more extensive than soft ones. Based on the test results, mechanisms of HDI failure with picoslider were presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2646-2653
• /
• 2000

The performance of slider of a hard disk drive affects the durability of the system. Particularly, the flying ability of the slider is critical in terms of surface damage and head crash. In this work, the take-off characteristics of the slider for various types of laser zone textured bump geometries were investigated. Also, the effect of ambient pressure on the flying characteristics of the slider was experimentally observed. An index of air density which can be used as a parameter for evaluating the flying characteristic is introduced.

• Electrical & Electronic Materials
• /
• v.11 no.10
• /
• pp.72-77
• /
• 1998

The effects of Al micro-bumps on the magnetic properties of CoCr(Pt)Ta/Cr films deposited on glass substrates were investigated. The coercivity increased and the coercivity squareness decreased by incorporating Cr/Al underlayers. The cause of the coercivity increase is attributed to the reduction of Co(0002) texture, the increase of magnetic isolation of CoCr(Pt)/Ta grains, and the refinement of CoCr(Pt)/Ta grains deposited on Cr/Al underlayers. The effects of an Al overlayer on the magnetic properties of CoCr(Pt)Ta/Cr films were also studied. The decrease of coercivity squareness is ascribed to the magnetic isolation of CoCr(Pt)Ta grains.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1589-1595
• /
• 2000

레이저 텍스쳐와 미케니칼 텍스쳐 컴퓨터 하드디스크의 마찰과 마코 매카니즘이 Contact Start/Stop test 실행후의 특성들에 대해 연구되었다. 다양한 분석적이고 기계적인 테스트 기술들이 이용되었다. 형상, 조도, 화학적 조성, 기계적 성질, CSS 로부터 기인된 코팅의 마찰특성들에 대해 그 변화들을 조사하였다. 즉, AFM(Atomic Force Microscopy), Nano-Indentation, Nano-Scratch, TOF-SIMS(Time of Flight Secondary Ion Mass Spectroscopy), AES(Auger Electronic Spectroscopy)등이 이 연구에 적용되었다. 레이저 텍스쳐 범프의 표면조도와 미케니칼 텍스쳐 지역의 표면조도는 각각 대략적으로 4nm 와 7nm 감소되었다. 탄성계수와 경도값은 CSS test후에 증가하였고 가장 바깥쪽의 코팅층의 변형강화가 생겨났다. 자성층과 Ni-P 층 사이에 점착성의 문제가 확인되었다. TOF-SIMS 분석은 C 와 $C_2F_5$의 세기에 있어서 감소를 드러냈고 이것은 코팅 표면에 윤활제 요소의 마모를 확실시 할수 있는 결과로 나타났다.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.51-57
• /
• 2005

Surface texturing of tribological applications is an attractive technology of engineered surface. Therefore, reduction of friction is considered to be necessary for improved efficiency of machines. The current study investigated the potential of textured micro-scale grooves on bearing steel flat mated with pin-on-disk. We discuss reducing friction due to the influence of sliding direction at surface pattern. We can indicate lubrication mechanism as a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for the lubrication condition. It was found that the friction coefficient was changed by the surface pattern and sliding direction, even when surface pattern was the same. It was thus verified that micro-scale grooves could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions. The lubrication regime influences the friction coefficient induced by the sliding direction of groove pattern. The friction coefficient depends on a combination of resistance force and hydrodynamic.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.6
• /
• pp.473-479
• /
• 2017

CrN coatings have been used as protective coatings for cutting tools, forming tools, and various tribological machining applications because these coatings have high hardness. Cr-Al-N coatings have been investigated to improve the properties of CrN coatings. Cr-Al-N coatings were fabricated by a hybrid physical vapor deposition method consisting of unbalanced magnetron sputtering and arc ion plating with different working pressure and substrate bias voltage. The phase analysis of the composition was performed using XRD (x-ray diffraction). Cr-Al-N coatings were grown with textured CrN phase and (111), (200), and (220) planes. The adhesion strength of the coatings tested by scratch test increased. The friction coefficient and removal rate of the coatings were measured by a ball-on-disk test. The friction coefficient and removal rate of the coatings decreased from 0.46. to 0.22, and from $2.00{\times}10^{-12}m^2/N$ to $1.31{\times}10^{-13}m^2/N$, respectively, with increasing bias voltage. The tribological properties of the coatings increased with increasing substrate bias voltage.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.