• Korean Chemical Engineering Research
• /
• 제59권3호
• /
• pp.410-416
• /
• 2021

To improve the capacity and stability of natural graphite, the electrochemical performances were investigated by using the prepared natural graphite coated with petroleum pitch for anode materials. The pitch coated natural graphite was prepared using a dry speed mixer by adjusting the rotation speed of the mixer, time, composition of graphite and softening point of the pitch. The physical properties of the anode material were analyzed using SEM, TEM, and PSD. The electrochemical performances were investigated by cycle, C-rate, EIS and CV test. When the pitch coated natural graphite was tested in the condition of 9000 RPM, 10 wt%, 2 h, and softening point of 150 ℃, it showed the highest capacity of 324.5 mAh/g at 0.1 C and a capacity retention rate of 98.9% after 50 cycles. In the test for evaluating rate performance, the capacity retention rate (5 C/0.1 C) was 80.3% and was improved by about 1.7 times over the pristine natural graphite.

• Journal of Korean Society of Environmental Engineers
• /
• 제22권7호
• /
• pp.1173-1182
• /
• 2000

The rapid mixing process has been considered as an important step in water treatment. Since the coagulant dispersion into raw water by rapid mixer can influence on the flocculation and filtration efficiency, many researchers have developed various devices and mixing methodologies. Until now, they focused attention on only coagulant dose, pH. rotating velocity and G value but overlooked the real turbulent flow and mixer geometry in rapid mixer. Therefore this paper questions the significance of turbulent flows in rapid mixer and focuses on the analysis of turbulent fluid in various mixer geometry with CFD(Computational Fluid Dynamics). The results of the jar-tests using various geometries indicate that the turbidity removal rate in a circular jar without baffle is higher than that of a circular with baffle. And the turbidity removal rate in Hudson jar is also founded to be higher than in the circular jar with baffle. The CFD simulation of velocity fields in jar demonstrates that the differences of removal rates among the various geometries are largely due to the formation of the different turbulent fluids fields with different geometries.

• International Journal of Highway Engineering
• /
• 제3권4호
• /
• pp.93-103
• /
• 2001

This study focused on the field applicability evaluation of SB latex-modified concrete (LMC) for concrete bridge deck overlay using mobile mixer. The main experimental factors were water-cement ratio(31, 33, 35 37%), latex contents(0, 5, 10, 15, 20%), and fine aggregate ratio(55, 56, 57, 58%) in order to evaluate the workability, mechanical properties, and durability property of LMC. The slump loss, air content, compressive and flexible strength tests were used to evaluate LMC workability and strength properties. Also, the rapid chloride permeability test was used to evaluate the relative permeability of LMC. As a results, the LMC with enough workability and good quality was produced when it was mixed in field using mobile mixer, satisfying the target compressive strength and flexural strength. The required water-cement ratio of LMC for same workability when mixing with mobile mixer was less than that when mixing in laboratory. Increasing the amount of latex produced concrete with increased flexural strength by mobile mixer. The required cement-water ratios for same initial $19{\pm}3cm$ slump were 37% and 33% at laboratory and mobile mixer, respectively. The mobile mixer was accurately calibrated satisfying the required specification.

• Korean Journal of Occupational Health Nursing
• /
• 제28권1호
• /
• pp.44-52
• /
• 2019

Purpose: This study aimed to identify the level of health problems and the factors that affect health problems for concrete mixer truck divers. Methods: The questionnaires were administered to 111 drivers in 6 Remicon workplaces located in D city and 7 Remicon workplaces located in K city from September 10 to 28, 2018. A total of 111 questionnaires were collected and 106 were used, excluding 5 incomplete ones. Data were analyzed with frequency, percentage, $x^2$ test, multiple logistic regression analysis by SPSS/WIN 23.0. Results: The factors affecting subjective health were eating habits, sleeping hours and drinking conditions. The factors that affected chronic diseases were age, eating habits, sleep hours, and drinking conditions. The factors influencing musculoskeletal complaints were work experience, eating habits, and sleep hours. Conclusion: The major influencing factors of health problems were eating habits, sleeping hours. This study suggests that it is necessary to run a systematic health care program for the desirable health behaviors in the communities and industrial fields.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• 제35S권9호
• /
• pp.9-18
• /
• 1998

A single RF transceiver chip for an extended GSM handset application was designedm, fabricated and evaluated. A RFIC was fabricated by using silicon BiCMOS process, and then packaged in 80 pin TQFP of $10 {\times} 10 mm^{2}$ in size. As a result, it was achieved guite reasonable integraty and good RF performance at the operation voltage of 3.3V. This paper describes development results of RF receiver section of the RFIC, which includes LNA, down conversion mixer, AGC, switched capacitor filter and down sampling mixer. The test results show that RF receiver section is well operated within frequency range of 925 ~960 MHz, which is defined on the extended GSM specification (E-GSM). The receiver section also reveals moderate power consumption of 67 mA and minimum detectable signal of -105 dBm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제30권6호
• /
• pp.734-740
• /
• 2006

The purpose of this study is to develop and commercialize a paddle-type fluidized dryer. The drying system used in this study, was designed to attach a paddle-type fluidized mixer to a dryer. The drying system is based on the drying method to generate thermal contacts, as fluidized layers are generated due to a paddle mechanism. Accordingly, the time of drying is short and material damage is very little. Also, the drying system operates as a closer system so it can be utilized not only for food and chemical materials, but also for environmental pollution materials. According to its performance test, the drying system is possible to dry low-moisture contents and its drying performance is outstanding. In conclusion, the drying system designed for this study, is likely to have great potential for commercialization.

• Korean Journal of Soil Science and Fertilizer
• /
• 제41권4호
• /
• pp.239-246
• /
• 2008

This research tried to find out the optimum fabrication method of calcined clay granules comprising zeolite. Kaolin clay and natural zeolite powder were used as raw materials of calcined clay, and silica stone powder was used for controlling the porosity of the granules. The granulation was performed with two kinds of granulators: a pan granulator and a high-shear mixer granulator. Various granules were fabricated by the mixing ratios and the rotation speeds of the granulators, and were heated from 400 to $700^{\circ}C$ at $100^{\circ}C$ interval. The crushing strength, pore size distribution, and CEC of the granules were measured. The evaluation method for the resistance of granules to human treading was created and the tests were conducted at dry and wet conditions. The resistance and crushing strength improved in proportion to the rotation speed of the granulator and the heating temperature, but the CEC decreased. The pellet made by the pan granulator did not have the strength against treading upon heating to below $700^{\circ}C$, but the pellet made by the high-shear mixer granulator endured the treading test upon heating to over $500^{\circ}C$

• Journal of the Korea Society of Computer and Information
• /
• 제22권1호
• /
• pp.63-69
• /
• 2017

In this paper, we propose a method to optimize the geometry and installation position of the mixer in the selective catalytic reduction (SCR) system by computational fluid dynamic(CFD). Using the commercial CFD software of CFD-ACE+, the flow dynamics of the flue gas was numerically analyzed for improving the injection uniformity of the reduction agent. Numerical analysis of the mixed gas heat flow into the upstream side of the primary SCR catalyst layer was performed when the denitrification facility was operated. The characteristics such as the flow rate, temperature, pressure loss and ammonia concentration of the mixed gas consisting of the flue gas and the ammonia reducing gas were examined at the upstream of the catalyst layer of SCR. The temperature difference on the surface of the catalyst layer is very small compared to the flow rate of the exhaust gas, and the temperature difference caused by the reducing gas hardly occurs because the flow rate of the reducing gas is very small. When the mixed gas is introduced into the SCR reactor, there is a slight tendency toward one wall. When the gas passes through the catalyst layer having a large pressure loss, the flow angle of the exhaust gas changes because the direction of the exhaust gas changes toward a smaller flow. Based on the uniformity of the flow rate of the mixed gas calculated at the SCR, it is judged that the position of the test port reflected in the design is proper.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제24권9호
• /
• pp.1195-1209
• /
• 2000

The purpose of this study is to develop the non-gravity fluidized dryer. In this non-gravity fluidized dryer the fluidized zone is produced by two paddles in mixer, which maximizes the surface area of materials and then heated air through the guiding panels dehumidify them. This can conduct the drying process quickly and control moisture contents to lower limits. The ventilation system is closed loop system, which can be changeable to open system, and can be used as a multi-purposed dryer in which mixing, drying, granulating and cooling process is conducted. In order to develop the non-gravity fluidized dryer, in the first fundamental experiments were performed to mixing accuracy and then the other parts of dryer and control system were examined to check whether they were designed properly and operated harmoniously with mixer. Also the preparatory experiments were fulfilled to examine the efficiency and reliability of the dryer. Lastly, on the basis of preparatory experiments, performance test for the non-gravity fluidized dryer carried out for the variation of the initial moisture contents, desired moisture contents, heated air velocity and heating temperature.

• The Journal of Advanced Prosthodontics
• /
• 제8권5호
• /
• pp.372-379
• /
• 2016

PURPOSE. Alginate mixers available in the market do not have the automatic proportioning unit. In this study, an automatic proportioning unit for the alginate mixer and controller software were designed and produced for a new automatic proportioning unit. With this device, it was ensured that proportioning operation could arrange weight-based alginate impression materials. MATERIALS AND METHODS. The variation of coefficient in the tested groups was compared with the manual proportioning. Compression tension and tear tests were conducted to determine the mechanical properties of alginate impression materials. The experimental data were statistically analyzed using one way ANOVA and Tukey test at the 0.05 level of significance. RESULTS. No statistically significant differences in modulus of elastisity (P>0.3), tensional/compresional strength (P>0.3), resilience (P>0.2), strain in failure (P>0.4), and tear energy (P>0.7) of alginate impression materials were seen. However, a decrease in the standard deviation of tested groups was observed when the customized machine was used. To verify the efficiency of the system, powder and powder/water mixing were weighed and significant decrease was observed. CONCLUSION. It was possible to obtain more mechanically stable alginate impression materials by using the custom-made proportioning unit.