• Journal of Welding and Joining
• /
• 제7권4호
• /
• pp.46-55
• /
• 1989

Zirconia coatings are performed by the plasma spraying on the substrate of Al-Si alloy. In case of plasma sprayed ceramic coatings, it is important to control properly residual stress occurred during cooling process. Residual stress in coating layer varies with sprayed conditions and is influenced greatly by the coating layer thickness. Surface residual stress due to coating layer thickness is measured by X-ray diffraction method and the residual stress in coating layer is estimated by the deflection of coating layer when the restraint force in substrate was removed. When zirconia was coated on the substrate, tensile residual stress remains on zirconia coated surface layer. The tensile stress is increased to 0.35mm thickness and after 0.45mm thickness it is decreased abrouptly. A thick bond and composite coating reduce the zirconia surface stress and composite coating controls effectively the thick zirconia surface stress.

• Advances in Computational Design
• /
• 제4권4호
• /
• pp.343-365
• /
• 2019

Among the themes related to earthquake countermeasures at construction sites, those for tower cranes are particularly important. An accident involving the collapse of a crane during the construction of a skyscraper has serious consequences, such as human injury or death, enormous repair costs, and significant delays in construction. One of the causes of deadly tower crane collapses is the destruction of the site joints of the tower crane mast. This paper proposes a new design method by static elastoplastic finite element analysis using a supercomputer for the design of the end plate-type tensile bolted joints, which are generally applied to the site joints of a tower crane mast. This new design method not only enables highly accurate and reliable joint design but also allows for a design that considers construction conditions, such as the introduction of a pre-tension axial force on the bolts. By applying this new design method, the earthquake resistance of tower cranes will undoubtedly be improved.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.589-595
• /
• 2011

Laminated glass fiber-reinforced plastic (GFRP) composites were applied to an insulating structure of a magnet system for a nuclear fusion device. Decreased inter-laminar strength by a strong repulsive force between coils which is induced a problem of structural integrity in laminated GFRPs. Therefore, it is important to investigate the inter-laminar characteristics of laminated GFRP composites in order to assure more reliable design and better structural integrity. Three types of the laminated GFRP composites using a high voltage insulating materials were fabricated according to each molding process. To evaluate the grade of the fabricated composites, mechanical tests, such as hardness, tensile and compressive tests,were carried out. The autoclave molding composites satisfied almost of the mechanical properties reguested at the G10 class standard, but the vacuum impregnation (VPI) and Prepreg composites did not.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.153-154
• /
• 2017

Graphene is a nanomaterial and is known to have very high mechanical strength, thermal and electrical properties. However, graphene is known to be difficult to disperse among carbon-based materials due to van der Waals force. In this study, to solve the dispersion problem of graphene nanoplatelet, oxidized graphene nanoplatelet was prepared by oxidizing GNP in nitric acid. The prepared GO was dispersed in ethanol and distilled water before incorporation into the epoxy paint to confirm dispersibility. In addition, GNP/Epoxy and GO/Epoxy tensile specimens were prepared by mixing GNP and GO at 0.1, 0.3, 0.5 and 1.0 wt.% In epoxy coatings and tensile stress-strain characteristics were investigated.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.319-320
• /
• 2023

In a reinforced concrete structure, coupler construction is easier to install than jointing or welding reinforcing bars, so it is possible to work by one person. When constructing a reinforcing bar coupler, the coupler construction method must be different for each member that receives a large tensile force or a member that receives a small tensile strength. Various coupler products are used in the global construction market, and the quality, performance, and cost of reinforcing bar joints vary from product to product. This study compares and analyzes the quality and cost of representative rebar couplers according to the requirements using the quality house of QFD-HOQ. The case study presents a quality and cost improvements strategy through QFD-HOQ analysis of rebar couplers.

• 구강회복응용과학지
• /
• 제22권1호
• /
• pp.11-21
• /
• 2006

The adjustable dental impression trays were made for being adjusted their width automatically along the width of patient's dental arch. The purpose of this study was to investigate the retentive force of adjustable dental impression trays made of different synthetic resin materials. Three pairs of adjustable trays were made of ABS(acrylonitrile butadiene styrene) synthetic resin, polyurethane synthetic resin and polycarbonate synthetic resin with a hole and without a rim on the border area of them. The experiment was done with the horse-shoe shaped metal plate to pull out the set impression body from the tray jig which was made for holding the tray on the lower part of Universal Testing Machine(UTM, Zwick Z020, Zwick Co., Germany). After the alginate impression in the tray was allowed to set four minutes, a tensile force was applied at right angles to the tray which had been previously seated on the jig. The force was applied to measure a maximum force by use of UTM at a constant strain rate 100mm per minute. The results obtained in this study were as follows : 1. The upper trays were showed higher retentive force than lower trays in three tray materials. 2. There was no significant difference in the retentive force of the tray materials(p>0.05).

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권6호
• /
• pp.47-53
• /
• 2022

콘크리트구조물의 한계상태설계법이 적용되면서 구조물의 극한상태까지 고려하는 설계가 이루어지고 있다. 실제 철근콘크리트 부재가 인장력을 부담할 때 부재가 항복한 후에도 극한상태까지 콘크리트가 인장력을 부담한다. 따라서 한계상태 거동에 대한 정확한 평가를 위해서는 휨 부재의 항복 후 인장강화효과에 대한 연구가 필요하다. 본 연구에서는 복철근 직사각형 단면을 가지는 RC 단순보에 대하여 4점 휨 실험을 수행하였고, 영상분석기법을 이용하여 부재의 거동을 상세하게 분석하였다. 분석 결과를 이용하여 휨 인장강화효과 계수를 도입한 항복 후 인장강화효과 추정식을 제안하였고, 이를 기존 연구들의 실험 결과를 통해 적용성을 검증하였다. 부재의 연성거동을 대표하는 극한 변형률과 항복 변형률 차이가 실험 결과와 유사하게 나타나 제안식의 예측이 비교적 정확한 것으로 판단된다.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권1호
• /
• pp.45-52
• /
• 2015

섬유복합체 (Fiber Reinforced Polymer, FRP)는 비강도가 높고, 비부식성 재료라는 특징을 가지고 있어서 건설 분야에서 철근을 대체할 수 있는 보강근 재료로 인식되고 있다. 몇몇 유리섬유 복합체 (Glass FRP, GFRP) 보강근이 상용화되어 있지만 GFRP는 철근에 비해 가격이 비싸고 상대적으로 낮은 탄성계수와 취성 파괴 특성 때문에 다소 경쟁력이 떨어진다. GFRP 보강근의 재료가격을 낮출 수 없다면 사용된 재료의 성능을 최대로 하여 보강근의 성능을 높이는 것이 상대적인 가격을 낮추는 방법이 될 수 있다. 일반적으로 FRP 보강근의 직경이 커질수록 인장강도는 감소하는 것으로 알려져 있다. 이의 원인 중 하나는 보강근이 인장을 받을 때 외력이 중앙에 위치한 섬유에 충분히 전달되지 못하여 외측에 위한 섬유들만이 인장에 저항하기 때문이다. 따라서 본연의 역할을 수행하지 못하는 섬유는 제거함으로써 보강근의 단가를 낮추면서 보강근이 소정의 성능을 발휘하도록 한다면 가격대비 성능이 최적화된 FRP 보강근을 제작할 수 있다. 본 연구에서는 직경 19 mm의 GFRP 보강근에 대해 단면 내에 중공이 존재하는 경우 중공비율에 따른 인장특성의 변화를 실험적으로 관찰하였다. 중공이 없는 GFRP 보강근 세 개, 네 가지 중공비율에 대해 각각 여섯 개의 GFRP 보강근 시편을 준비하여 인장실험을 실시하였으며 결과 분석을 통하여 인장특성 변화를 도출하였으며 이를 바탕으로 최적의 중공비율을 제안하였다.

• 한국안전학회지
• /
• 제23권3호
• /
• pp.42-50
• /
• 2008

This study, push-off tests for the initially uncracked specimens were conducted to investigate shear transfer mechanism in reinforce concrete elements. Experimental programs for shear transfer were undertaken to investigate the effect of the concrete compressive strength, the presence of steel stirrups as shear reinforcement and the amount of steel stirrups. As the shear plane is loaded, several cracks form in a direction inclined to the shear plane, creating compression struts in the concrete. For this stage, shear is being transferred through a truss-like action produced by the combination of the compressive force in the concrete struts and the tensile force that the steel reinforcement crossing the shear plane develops. In the normal strength concrete specimens with steel stirrups, ultimate failure occurred when the compression struts crushed in concrete. In the high strength concrete specimens, on the other hand, ultimate failure occurred when the steel stirrups developed their yield strength.