• 오토저널
• /
• 제7권3호
• /
• pp.83-93
• /
• 1985

The prediction of emission concentrations in a 4cycle spark ignition engine was made by considering nonuniform model with thermodynamics, chemical equilibrium and kinetic mechanism of nitric oxide. Calculation of this model shows that a temperature difference of the order of 500K can be established across he cylinder. Results of the kinetic calculation of nitric oxide show that the temperature gradient across the cylinder has a profound effect on the nitric oxide formation. The predicted values for nitric oxide, carbon dioxide and carbon monoxide agree with measured ones for a variety of equivalence ratio.

• 한국농림기상학회:학술대회논문집
• /
• 한국농림기상학회 2012년도 학술발표논문집
• /
• pp.93-96
• /
• 2012

• 한국농림기상학회지
• /
• 제20권2호
• /
• pp.159-165
• /
• 2018

본 연구는 급격하게 진행되고 있는 기후변화에 따른 콩의 생육과 종실 수량 반응을 온도구배챔버에서 수행하였다. 생식상 장기간의 고온 발생은 농업 생산성을 저해시키며, 인류의 식품안정성에도 영향을 줄 수 있다. 모든 품종이 $Ta+4^{\circ}C$에서 개화기간이 지연되는 현상을 보여 영양생장기보다 생식생장기의 고온에 대해 민감하게 반응을 하였다. 온도 변화에 대한 종실 수량 구성 반응을 보면 대원콩은 온도가 상승 할수록 협수, 종실 무게가 높아져 수량이 증가하였다. 반면 풍산나물콩과 대풍콩은 각각 $Ta+3^{\circ}C$와 $Ta+4^{\circ}C$사이에서 각각 일정 온도를 벗어나게 되면 온도에 민감하게 반응하여 착협수와 100립중이 감소를 하여 수량 감소로 이어졌다. 종자 크기로 보았을 때 대립 품종인 대원콩은 일정 온도 범위까지는 수량이 증가 할 것으로 판단된다. 반면 중립과 소립품종인 대풍콩과 풍산 나물콩은 일정 온도를 벗어나게 되면 수량이 감소 할 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.90-99
• /
• 2002

The main purpose of this study lies on the development of micro dilution tunnel based on the Sierra Dilution chamber model. As a primary examination, characteristics of flow and temperature distributions during the steady dilution process in dilution chamber are observed with numerical analysis. The penetration of dilution air through porous tube as well as wall temperature and temperature gradient inside porous tube are examined. The thermophoretic velocity in terms of temperature behavior inside porous tube are defined and examined. Based on the ratio of penetration and thermophoretic velocities, all part of porous tube are shown to be safe from the particulate depositions. However, The inlet portion of porous tube in addition to the portion of impinging of dilution air are marginally safe from the particulate depositions. Generally the safer design against particulate deposition is required in provision f3r steady dilution process and for transient process as well.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.283-288
• /
• 1999

The sealing performance of an elastomeric O-ring seat with a temperature gradient has been analyzed for the contact stress behaviors that develop between the O-ring seal and the surfaces with which it comes into contact. The leakage of an O-ring seal will occur when the pressure differential across the seal just exceeds the initial (or static) peak contact stress. The contact stress behaviors that develop in compressed O-rings, in common case of restrained geometry (grooved), are investigated using the finite element method. The analysis includes material hyperelasticity and axisymmetry. The computed FEM results show that the contact stress behaviors are related to a compression rate and a temperature gradient between the vacuum chamber with a groove and the contacting plate with a cooling jacket.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.832-839
• /
• 2007

The geometry and dimensions of an expansion chamber are decisive factors in thermal puffer plasma chamber designs. Because they together dominate the temperature and speed at which the cooling gas from the chamber flows back through a flow channel to the arcing zone for the successful interruption of fault currents. In this study, we calculated the flow and mass transfer driven by arc plasma, and investigated the effects of a flow guide installed inside a thermal puffer plasma chamber. It is found that the existing cold gas of the chamber mixes with hot gases entrained from the arcing zone and is subjected to compression due to pressure build-up in the chamber. The pressure build-up with the flow guide is larger than that without due to a vortex which rotates clockwise around the chamber center. By the reverse pressure gradient, the mixing gas of the chamber flows back out for cooling down the residual plasma near current zero. In the case with the flow guide, the temperature just before current zero is lower than that without, and the Cu concentration with high electrical conductivity is also less than that without the flow guide.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• 한국주조공학회지
• /
• 제27권2호
• /
• pp.77-82
• /
• 2007

The effects of thermal gradient and solidification rate on the dendrite arm spacing and carbide morphology were investigated in directionally solidified Ni-base superalloy, CM 247LC. Thermal gradient was controlled by changing the position of the cold chamber and the furnace set temperature. The interface morphology changed from the planar to dendritic as increasing solidification rate. It was found that the dendrite spacing decreased as increasing the thermal gradient as well as the solidification rate. Also, as increasing solidification rate, carbide morphology changed from blocky shape to script and spotty shapes.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.480-485
• /
• 1993

Factros considered building the magnetron sputtering system for TFT LCD (thin film transistor liquid crystal display0 metallization were thin film thichnes uniformity, temperature uniformity and the pressure gradient of sputtering gas flow in vacuum chamber, base pressure, and the stability fo the carrier moving . The system was consisted of a deposition chamber, a pre-heating chamber, a RF-precleaning chamber and a load/unload lock chamber. The system was designed to handle a substrate with dimension of 400$\times$400mm. The temperautre uniformity of a heater table developed showed $250 ^{\circ}C\pm$5% accuracyon the substrate glass. A base pressure of 1.8 $\times$10-7 torr was obtained after 24 hours pumping with a cryo pump. After an aluminum target was installed in a sputtering source and the film wa sdeposited on the glass, the uniformity, reflectivity and sheet resistance of the deposited film were measured.

• 한국표면공학회지
• /
• 제43권6호
• /
• pp.309-314
• /
• 2010

The numerical study for the effect of various factors that affect the temperature distribution of the process glass installed above the large rectangular heater plate was carried out. For the calculation, heat flux, distance between heat source and process glass plate, effect of vacuum condition and convection in a chamber were considered as important factors. The results showed that the temperature gradient on the glass was increased at the natural convection because of the buoyancy force increases due to the heated air. Also, the more heat flux and distance between the heater plate and glass increases, the more increasing the temperature gradient was. In the case of isothermal heating wall, the temperature variation was smaller than the uniform heat flux condition.