• 한국응용과학기술학회지
• /
• 제31권4호
• /
• pp.679-687
• /
• 2014

본 연구에서는 캐비테이션에 의한 부식에 강한 도료를 개발하기 위하여 고탄성의 우레탄 수지에 내마모 성능을 향상시키기 위한 첨가제로서 Multi wall과 Single wall type의 Carbon nano tube(CNT)와 Spherical과 Fiber type의 Graphite 나노 입자를 첨가하여 물성과 캐비테이션에 대한 저항성, 작업성 등을 비교 평가하였다. 나노 입자로서 Graphite에서는 캐비테이션 저항성($t_{50}$)이 Spherical type($t_{50}$ 182min)보다는 Fiber type($t_{50}$ 292min)이 높은 캐비테이션 저항성을 갖는 것으로 관찰되었다. 또한 CNT에서는 Single wall type의 캐비테이션 저항성($t_{50}$ 286min)이 Multi wall보다는 더 높은 것으로 관찰되었다. 나노 입자중에서 가격 및 캐비테이션 저항성을 감안하면 가장 최적의 나노 입자는 Fiber type의 Graphite로 관찰되었다. 도료의 작업성 평가에서 수동 작업에 의해 제작된 표면은 매끈한 표면을 가지고 있으나 Spray 작업에 의해 제작된 표면은 표면이 균일하지 않으며 Spray시 발생된 Dust가 표면에 고착된 형태로 관찰되었다.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1540-1555
• /
• 2021

The plate-type fuel assembly adopted in nuclear research reactor suffers from complicated effect induced by non-uniform irradiation, which might affect its stress conditions, mechanical behavior and thermal-hydraulic performance. A reliable numerical method is of great importance to reveal the complex evolution of mechanical deformation, flow redistribution and temperature field for the plate-type fuel assembly under non-uniform irradiation. This paper is the first part of a two-part study developing the numerical methodology for the thermal-fluid-structure coupling behaviors of plate-type fuel assembly under irradiation. In this paper, the thermal-fluid-structure coupling methodology has been developed for plate-type fuel assembly under non-uniform irradiation condition by exchanging thermal-hydraulic and mechanical deformation parameters between Finite Element Model (FEM) software and Computational Fluid Dynamic (CFD) software with Mesh-based parallel Code Coupling Interface (MpCCI), which has been validated with experimental results. Based on the established methodology, the effects of non-uniform irradiation and fluid were discussed, which demonstrated that the maximum mechanical deformation with irradiation was dozens of times larger than that without irradiation and the hydraulic load on fuel plates due to differential pressure played a dominant role in the mechanical deformation.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1556-1568
• /
• 2021

The plate-type fuel assembly adopted in nuclear research reactor suffers from complicated effect induced by non-uniform irradiation, which might affect stress conditions, mechanical behaviors and thermal-hydraulic performance of the fuel assembly. This paper is the Part II work of a two-part study devoted to analyzing the complex unique mechanical deformation and thermal-hydraulic characteristics for the typical plate-type fuel assembly under irradiation effect, which is on the basis of developed and verified numerical thermal-fluid-structure coupling methodology under irradiation in Part I of this work. The mechanical deformation, thermal-hydraulic performance and Mises stress have been analyzed for the typical plate-type fuel assembly consisting of support plates under non-uniform irradiation. It was interesting to observe that: the plate-type fuel assembly including the fuel plates and support plates tended to bend towards the location with maximum fission rate; the hot spots in the fuel foil appeared at the location with maximum thickness increment; the maximum Mises stress of fuel foil was located at the adjacent location with the maximum plate thickness increment et al.

• 천문학회보
• /
• 제44권1호
• /
• pp.76.2-76.2
• /
• 2019

Shells in early-type galaxies are low surface brightness tidal debris, which are wide concentric arcs of overdense stellar regions with large opening angles. The most widely accepted mechanism today for shell formation is the merger scenario, but the dominant merger type producing shells is not clearly understood yet: major/minor and wet/dry mergers. Since shells are regarded as smoking-gun evidence of merging events, detailed understanding of shell galaxies is very useful to constrain the formation process of early-type galaxies. In this study, we investigate the metallicity gradients of eight early-type shell galaxies using CALIFA IFU data to better understand the nature and origins of galaxy shells. We estimate simple stellar population properties out to three effective radius from the measurement of Lick/IDS absorption line indices. We compare the metallicity gradients of shell galaxies with those of normal early-type galaxies in the same mass range. In this presentation, we discuss how much the gradients of shell galaxies are different from those of normal early-type galaxies and what the existence of galaxy shells implies about galaxy formation.

• Journal of Microbiology and Biotechnology
• /
• 제6권1호
• /
• pp.68-69
• /
• 1996

The isoprenoid quinone composition of Leclercia adecarboxylata KCTC $1036^T$ was determined by using high-performance liquid chromatography. L. adecarboxylata KCTC $1036^T$ are characterized by their production of both ubiquinone-7, ubiquinone-8 and menaquinone-8 as major quinones. It is clear that the analysis of isoprenoid quinone profiles provides a new criterion of great promise for identifying Leclercia strains.

• 한국재료학회지
• /
• 제26권4호
• /
• pp.222-227
• /
• 2016

Tin oxides have been studied for various applications such as gas detecting materials, transparent electrodes, transparent devices, and solar cells. p-type SnO is a promising transparent oxide semiconductor because of its high optical transparency and excellent electrical properties. In this study, we fabricated p-type SnO thin film using rf magnetron sputtering with an SnO/Sn composite target; we examined the effects of various oxygen flow rates on the SnO thin films. We fundamentally investigated the structural, optical, and electrical properties of the p-type SnO thin films utilizing X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV/Vis spectrometry, and Hall Effect measurement. A p-type SnO thin film of $P_{O2}=3%$ was obtained with > 80% transmittance, carrier concentration of $1.12{\times}10^{18}cm^{-3}$, and mobility of $1.18cm^2V^{-1}s^{-1}$. With increasing of the oxygen partial pressure, electrical conductivity transition from p-type to n-type was observed in the SnO crystal structure.

• Journal of Electrical Engineering and Technology
• /
• 제6권4호
• /
• pp.474-483
• /
• 2011

Solid-state fault current limiters (SSFCL) in power systems are alternative devices to limit prospective short circuit currents from reaching lower levels. Fault current limiters (FCL) can be classified into two categories: R-type (resistive) FCLs and L-type (inductive) FCLs. L-type FCL uses an inductor to limit fault level and is more efficient in suppressing voltage drop during a fault. In contrast, R-type FCL is constructed with a resistance and is more effective in consuming the acceleration energy of generators during a fault. Both functions enhance the transient stability of the power system. In the present paper, a novel SSFCL is proposed to enhance power system transient stability and power quality. The proposed SSFCL uses both functions of an L-type and R-type FCL. SSFCL consists of four diodes, one self-turn-off IGCT, a current-limiting by-pass inductor (L), and a variable resistance parallel with an inductor for improvement of power system stability and prevention of over-voltage across SSFCL. The main advantages of the proposed SSFCL are the simplicity of its structure and control, low steady-state impedance, fast response, and the existence of R-type and Ltype impedances during the fault, all of which improve power system stability and power quality. Simulations are accomplished in PSCAD/EMTDC.

• 한국기계가공학회지
• /
• 제19권8호
• /
• pp.43-49
• /
• 2020

The growth of the AR/VR market due to the advent of the 4th Industrial Revolution begins with the development of the display industry. The development of OLED and flexible displays is further accelerated by the development of R2R technology. Micro-processing technology using a fast tool servo (FTS), the core technology in R2R processes, is making technological progress in increasingly diverse ways. This paper proposes a method to develop an FTS for horizontal driving and presents this method through experiments and analyses. To develop a swing-type FTS based on a seesaw motion, a rotational moment hinge structure was designed for each type, and research was conducted to determine an effective design method. A cantilever-based swing-type FTS was developed in two variations: one with single-side hinges and another with dual-side hinges. The parameters in the design of the swing-type FTS are rotational moment, natural frequency, and material selection. In conclusion, an FTS with a single-side hinge demonstrates the high performance required for micro processing.

• Current Research on Agriculture and Life Sciences
• /
• 제29권
• /
• pp.63-74
• /
• 2011

The purpose of this study is a classification of farm typology and an analysis of characteristic e-commerce type of farm enterprises. The classification of sample farm enterprises thus results in six distinctively agribusiness type. The six identified types can be characteristic as follows: production type, processing type and distribution type, e-commerce type, export-agricultural type, amenity-tourism type. This article attempted to come up with workable strategies to solve these problems affecting e-commerce type farm enterprises. The main results this paper are as follows: 1) to make organization of e-commerce type farm enterprises to accomplish business goals 2) to find out solution for urgent problems and subjects of farm management 3) to practice profitable business model for e-commerce type. E-commerce type farm enterprises needs are not only technology transference but also farm management.

• Journal of the Korean Wood Science and Technology
• /
• 제4권1호
• /
• pp.38-47
• /
• 1976

This study was carried out to exploit and utilize American sycamore (Platanus occidentalis) and poplar grown in Korea as veneer species for plywood manufacture. At this study to save the imported lauan logs and dollars, the effects affecting to the properties of plywood constructed by sycamore, poplar and lauan veneers were studied. Important items dealt with this study were dry and wet shear strength, moisture content, and specific gravities By the results and discussion it may be summarized as followings. 1) Sycamore core lauan plywood (A-II type) was shown best dry shear strength, and the next were all lauan veneer plywood (A-I type), poplar core lauan plywood (B-I type), lauan core sycamore plywood (A-III type) in order. There are no differences between dry shear strength of A-II type and A-I type, A-II type and B-I type plywood. 2) Wet shear strength showed the same order with dry shear strength. A-II type plywood showed best wet shear strength and it showed more difference than other plwoods. A-I type, B-I type and A-III type plywood were all very good without significant difference in wet shear strength. 3) B-I type plywood showed highest moisture content of all type plywood and the next were all sycamore(A-IV type) all poplar plywood (B-III type), A-III type, B-II type, A-II type pllywood in order. Generally high moisture content showed when two or three veneers were same species in the three layer plywood. 4) A-III type plywood showed highest specific gravity of all and the next was A-IV type plywood without a difference to A-I type plywood on the whole. plywoods constructed by lauan and sycamore were shown high specific gravities and the next was lauan, sycamore and poplar, lauan and poplar. It seemed to be that connected wi th the specific gravity of veneer itself in different species. 5) The plywood manufactured by extension of potato flour is not only superior but also profitable in the price aspect than the plywood manufactured by extension of wheat flour.