• 한국염색가공학회지
• /
• 제26권3호
• /
• pp.201-208
• /
• 2014

The high value-added functionality for synthetic fiber can be considered through a plasma enhanced treatment. In this study, PET(Polyethyleneterephthalate) was treated with a glow plasma and corona treatment. Surface characteristics of treated fabric were investigated using electron scanning microscopy(SEM), contact angle, X-ray photoelectron spectroscopy(XPS), tensile and adhesion strength. It was found that the contact angle showed $85.5^{\circ}$ for untreated fabric, $0^{\circ}$ for plasma and corona treatment at the condition of 200W for 7min. By XPS analysis, atomic ratio of O 1s/C 1s was increased from 0.27 to 0.43 by glow plasma and 0.27 to 0.41 by corona treatment at 200W for 7min, respectively. Glow plasma and corona treatment did not significantly change the tensile strength of PET fabric. Adhesion strength showed a substantial enhancement for the surface treated with the glow plasma, while corona treatment was adversely affected.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.63-70
• /
• 2014

This study has attempted to figure out the effects of the surface heat of perm rods on hair. For this, after forming perm waves, hair damage and its causes have been investigated with a different hair bleach method. If hair was bleached immediately without shampooing after a perm using the heat of rods, great perm waves were formed. However, severe damage was found on the hair because of the heated rods. In addition, when hair was shampooed and dried after the perm, hair bleach was more effective. It has been confirmed that hair was damaged because of high temperature of the surface of the rods. In fact, the heated rods had a direct effect on hair damage. According to these results, it has been confirmed that heat-based perms can accelerate hair damage. Therefore, it is necessary to perform a study on the minimization of the heating of permanent tools.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.32-38
• /
• 2014

There has been increasing demand to the eco-friendly materials such as phytoncide which is extracted to plants in the textile industry, recently. It is interesting that alginic acid sodium salt(Alg-Na) is used to eco-friendly binder for the functional capsule finishing. In this study, we made PEO/Alg-Na blend solutions of various ratio and observed the changing binding property of the blend solutions according to PEO contents through FT-IR, DSC, contact angle, peel strength, etc. The viscosity of Alg-Na/PEO blend solutions increased with increase of contents and the viscosity quickly increased with increase of PEO content in Alg-Na 5% content, specially. It is shown that the hydrogen bond peak by blend of Alg-Na and PEO found through FT-IR analysis but the peak decreased in PEO above 60% content. And the peel strength was predominant in PEO 50% ratio.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.39-44
• /
• 2014

To confirm the performance and benefit of the developed online E-commerce Real Industrial Color(RIC) device, cotton and polyester were dyed with selected 39 colors. The captured images of dyed cotton and polyester by using RIC device were compared with original samples and confirmed ${\Delta}E$ using a spectrophotometer and RIC device. Overall, visual comparison of the captured images was similar to the real dyed samples. In high concentration of dyeings, the color consistency between real samples and captured images was better than in lower color concentration of dyeings. Similarly, the result was almost the same when the developed RIC device was used since ${\Delta}E$ values of RIC device were smaller compared with spectrophotometer. In this regards, the RIC device developed up to date can be assumed that it is more influenced by the color rather than fabric materials.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.13-21
• /
• 2014

The object of this research is to perform the basic research for the development of selectively permeable membrane fabrics which is suitable for korean military in sense of embattlement. As a key factor of selectively permeable membrane fabrics which is suitable for korean military, this study selected the best PVA thickness and membrane selection for DMMP protection, pre-treatment method for conformational stability of face fabric and water/oil repellent process condition. Especially as the PVA coating thickness of the fabrics increase, peneration of DMMP decrease including water vapor permeation is lower. This study shows how physical features and permeability of chemical agents can be influenced by pre-treatment methods, the selection of selectively permeable membrane, the thickness of PVA etc. Results showed that outer shell / PVA / e-PTFE materials possessed performance with superior water vapor permeation (Over $3,000g/m^2/day$) and protective capability against DMMP vapor ($0.6{\mu}g/cm^2{\cdot}16hr$).

• 한국염색가공학회지
• /
• 제20권1호
• /
• pp.48-56
• /
• 2008

A real-time inspection system has been developed by combining CCD based image processing algorithm and a standard lighting equipment. The system was tested for defective fabrics showing nozzle contact scratch marks, which are one of the frequently occurring defects. Two algorithms used were compared according to both their processing time and detection rate. First algorithm (algorithm A) was based on morphological image processing such as dilation and opening for effective treatment of defective printing areas while second one (algorithm B) mainly employs well-defined edge detection technique based on canny detector and Zermike moment. It was concluded' that although both algorithms were quite successful, algorithm B showed relatively consistent performance than algorithm A in detecting complex patterns.

• 한국염색가공학회지
• /
• 제23권1호
• /
• pp.43-50
• /
• 2011

Electrically conductive yarn coated with silver particles are widely used to make smart wear but recent studies on smart fabrics are focused on measuring method of electrical characteristics and improving technologies of its electric properties. Also durability of conductive yarn with environmental change was also important work to make smart fabric. We compared resistance changes of silver coated conductive yarns under various physical and chemical conditions such as repeated strain, heat exposure and pH for basic informations on smart wear manufacturing process. And we deduct that repeated strain among the physical conditions was most effective factors on yarn resistance change and the low resistance change was observed with increasing the number of filaments in identical yarn fineness.

• 한국염색가공학회지
• /
• 제23권1호
• /
• pp.51-59
• /
• 2011

Calcium alginate fiber were prepared by wet spinning of various conditions, including different concentrations of sodium alginate solution and $CaCl_2$ concentrations for coagulating the fiber through an absorption of calcium ion. The absorption of calcium ion during the coagulating step lead to solidify the fibers by the replacement of sodium ion with calcium ion to produce some crosslinking. The concentration of calcium ion in the calcium alginate fiber seems to be well related to the mechanical and physical property of the fiber, such as fiber strength moisture regain, and degree of swelling. The tensile strength of calcium alginate fiber was increased along with the increasing amount of sodium alginate solution. According to EDS analysis, 7 wt% $CaCl_2$ coagulation bath resulted in more calcium ion in the fiber compared to 3 wt% $CaCl_2$ coagulation bath. The decomposition temperature of calcium alginate fiber was $199^{\circ}C$, which $14^{\circ}C$ higher than that of sodium alginate.

• 한국염색가공학회지
• /
• 제24권2호
• /
• pp.145-151
• /
• 2012

Polymer alloys of poly(ethylene terephthalate)(PET) and nylon6(PA6) which were not miscible each other by themselves were successfully prepared through melt compounding using a twin-screw extruder by utilizing epoxy as reactive compatibilizer. At the epoxy(DGEBA) amount of 0.5~2wt%, the domain size(average diameter) of the discontinuous phase could be reduced up to 0.2${\mu}m$ from 1-5${\mu}m$ that of the simple blend without epoxy. The reaction was presumed to happen mostly at interphase from the result of maximum increase of melt viscosity at the middle range of PET/PA6 blend ratio. It is expected that alloy fibers of PET/epoxy/PA6 with enough mechanical strength for use can be prepared.

• 한국염색가공학회지
• /
• 제24권4호
• /
• pp.281-287
• /
• 2012

Poly(phenylene sulfide) films containing acetophenone as a photoinitiator were photocrosslinked under UV irradiation using a continuous UV irradiator. The gel fraction of the irradiated PPS in 1-Chloro naphthalene reached 94.7% with increasing UV energy and the photoinitiator concentration in the film upto $200J/cm^2$ and 12wt% respectively. Solid state $^1C$ NMR analysis suggested that the crosslinking occurred between the phenylene chains in PPS, indicating that the acetophenone may the phenylene hydrogens and subsequently adjacent polymer radicals could be recombined to form the crosslinked structure. The crosslinking improved the thermal behavior of PPS such as loss of $T_g$ and $T_c$, higher melting point and lower melting enthalphy as well as significantly higher peak pyrolysis temperature as much as $63.5^{\circ}C$. Surprisingly the tensile toughness of the most crosslinked PPS increased by 842%, resulting from the substantial enhancements in tensile modulus, strength and strain as much as 76%, 236% and 240% respectively. Also dynamic mechanical measurement indicated that the distance between crosslinks in the crosslinked PPS reached 85.3 g/mol corresponing to a crosslink density of 0.012 mol/g.