• Structural Engineering and Mechanics
• /
• v.63 no.1
• /
• pp.1-9
• /
• 2017

Shot peening is a cold surface treatment employed to induce residual stress field in a metallic component beneficial for increasing its fatigue strength. The experimental investigation of parameters involved in shot peening process is very complex as well as costly. The most attractive alternative is the explicit dynamics finite element (FE) analysis capable of determining the shot peening process parameters subject to the selection of a proper material's constitutive model and numerical technique. In this study, Ansys / LS-Dyna software was used to simulate the impact of steel shots of various sizes on an aluminium alloy plate described with strain rate dependent elasto-plastic material model. The impacts were carried out at various incident velocities. The influence of shot velocity and size on the plastic deformation, compressive residual stress and force-time response were investigated. The results exhibited that increasing the shot velocity and size resulted in an increase in plastic deformation of the aluminium target. However, a little effect of the shot velocity and size was observed on the magnitude of target's subsurface compressive residual stress. The obtained results were close to the published ones, and the numerical models demonstrated the capability of the method to capture the pattern of residual stress and plastic deformation observed experimentally in aluminium alloys. The study can be quite helpful in determining and selecting the optimal shot peening parameters to achieve specific level of plastic deformation and compressive residual stress in the aluminium alloy parts especially compressor blades.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.31-37
• /
• 2015

PURPOSES : To design a pre-heater for warm in-place recycling equipment, three different heating systems were evaluated to determine their thermal efficiency. METHODS: In this study, a $30cm{\times}30cm{\times}15cm$ wheel-tracking specimen was used to measure the inner temperature as a function of the heating system. The inner temperature of the specimen was measured with a data logger at the surface, and at depths of 1cm, 2cm, 3cm, 4cm, and 5cm. To evaluate the thermal efficiency, the researchers used three different types of equipment, namely, IR, a heating wire, and a gas burner. RESULTS: The IR heating system exhibits a higher level of performance than the others to achieve the target temperature at a depth of 5cm in the specimen. The gas burner system was capable of heating the surface to a temperature of up to $600^{\circ}C$. The other types, however, cannot heat the surface up to 600. The thermal efficiencies were measured based on the laboratory conditions. CONCLUSIONS: To find the most effective system for application to the development of a pre-heater for warm in-place recycling, various systems (IR, heating wire, gas burner) were examined in the laboratory. As a result, it was found that the hot plate of a gas burner system provides the highest temperature at the surface of the asphalt but, of all the systems, the IR system provides the best internal temperature increase rate. Furthermore, a gas burner can age the asphalt binder of the surface layer as a result of the high temperature. However, the gas burner cannot attain the target temperature at 5cm. The IR system, on the other hand, is effective at increasing the internal temperature of asphalt.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.139-146
• /
• 1996

Transparent and conducting Sb-doped $SnO_2$ thin films were prepared by rf magnetron sputtering technology. But it showed a serious damage phenomenon on the surface of as-deposited films. In order to avoid a damage caused in the substrate center and location facing to target erosion, a ring plate of masking glass was installed at 1.5 cm above target surface. The uniformity and electrical characteristic of $SnO_2$ thin films were evaluated by the control of optimal conditions in the magnetron sputtering operation such as rf power, sputtering gas pressure, and substrate temperature. In the experimental results using the operating conditions, the optimum temperature, which produced uniform and damageless films, shifted with the change of gas pressure. The rate was about $100^{\circ}C$/5 mTorr at rf power of 50 W Similarly, the optimum temperature in compensation for an increase of rf power shifted down to a proper rate.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.11
• /
• pp.79-88
• /
• 1999

In this paper we address the tracking method which tracks only target object in image sequence including moving object. We use a contour tracking algorithm based on intensity and motion boundaries. The motion of the moving object contour in the image is assumed to be well describable by an affine motion model with a translation, a change in scale and a rotation. The moving object contour is represented by B-spline, the position and motion of which is estimated along the image sequence. we use pattern recognition to identify target object. In order to use linear Kalman Filters we decompose the estimation process into two filters. One is estimating the affine motion parameters and the other the shape of moving object contour. In some experiments with dial plate we show that this method enables us to obtain the robust motion estimates and tracking trajectories even in case of including obstructive object.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.4
• /
• pp.269-278
• /
• 2017

Objective: The purpose of this study was to develop a goal setting method for increasing the probability of a holed in a side inclined putting stroke. Method: Three-dimensional video data was recorded at a frequency of 120 hz per second after synchronizing 19 infrared motion capture systems (Qualisys, Gothenburg, Sweden). Putting green used a polycarbonate plate ($1.2{\times}2.4{\times}0.01meter$) with coefficient of friction (${\mu}=0.062$) and a real curve of the actual hole. Results: The velocity ratio between the club and the ball was 1:1.6 under various ball speed conditions in this study. The overall position of the break is 1 m to 1.4 m from the point where the ball leaves. If there is a slope, the ball follows the target line by the straightening force, and when it reaches 1 m position, the straightening force decreases by 30~50% and reaches to the deviation (break) point which is severely influenced by the slope. From here, the ball is aimed in a direction other than the target, and the size is affected by the slope. Conclusion: If there is a side slope, the ball moves away from the straight line, and the larger the slope, the closer the break point is to the starting point of the ball. Therefore, it is necessary to calculate the degree of departure according to the slope carefully, and it is preferable that the slower the speed is, the more the influence of the slope becomes. It is preferable to use the center of the hole as a reference when calculating the departure.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.6
• /
• pp.736-741
• /
• 2012

In this study, we analyzed the oxidative stress response of wblA ($\underline{w}$hi$\underline{B}$-$\underline{l}$ike gene $\underline{A}$, SCO3579), which was previously shown to be a global antibiotic down-regulator in Streptomyces coelicolor. Ever since a WblA ortholog named WhcA in Corynebacterium glutamicum was found to play a negative role in the oxidative stress response, S. coelicolor wblA has been proposed to have a similar effect. A wblA-deletion mutant exhibited a less sensitive response to oxidative stress induced by diamide present in solid plate culture. Using real-time RT-PCR analysis, we also compared the transcription levels of oxidative stress-related genes, including sodF, sodF2, sodN, trxB, and trxB2, between S. coelicolor wild type and a wblA-deletion mutant in the presence or absence of oxidative stress. Target genes were expressed higher in the wblA-deletion mutant compared with wild type, both in the absence and presence of oxidative stress. Moreover, expression of these target genes in S. coelicolor wild type was stimulated only in the presence of oxidative stress, suggesting that WblA plays a negative role in the oxidative stress response of S. coelicolor, similar to that of C. glutamicum WhcA, through the transcriptional regulation of oxidative stress-related genes.

• The Korean Journal of Food & Health Convergence
• /
• v.6 no.5
• /
• pp.19-25
• /
• 2020

The purpose of this study was to research and develop a step-type chemical liquid deodorizer including a liquid catalyst that can prevent civil complaints due to odor due to its excellent deodorizing performance. The main composition of chemical liquid deodorizer including liquid catalyst is cleaning deodorization, catalyst deodorization, chemical deodorization, water film plate, deodorization water circulation device, deodorization water injection device, catalyst management system, gas-liquid separation device, chemical supply device, deodorizer control panel, etc. It consists of a device. The air flow of the step-type liquid catalyst chemical liquid deodorizer is a technology that firstly removes basic odor substances, and the liquid catalyst installed in the subsequent process stably removes sulfur compounds, which are acidic odor substances, to discharge clean air. The efficiency of treating the complex odor of the prototype was 98.5% for the first and 99.6% for the second, achieving the target of 95%. The hydrogen sulfide treatment efficiency of the prototype was 100% for the first and 99.9% for the second, which achieved 95%, which was the target of the project. As a result, ammonia was removed by the reaction of ammonia and hydrogen sulfide.

• Journal of the Korean Geosynthetics Society
• /
• v.20 no.3
• /
• pp.11-20
• /
• 2021

In this paper, the approximately coupled method of finite element method and boundary element method to obtain efficient and accurate analysis results is proposed for a two-dimensional elasto-static problem with a geometrically abruptly changing part. As the finite element of a two-dimensional problem, three-node and four-node plane stress element is applied, and as the boundary element of a two-dimensional problem, three-node boundary element is applied. In the modeling stage, firstly, an entire analysis target object is modeled as finite elements, and then a geometrically abruptly changing part is modeled as boundary elements. The boundary element is defined using the nodes defined for modeling finite elements. In the analysis stage, finite element analysis is firstly performed on a entire analysis target object, and boundary element analysis is automatically performed afterwards. As for the boundary conditions at boundary element analysis, displacement conditions and stress conditions, which are the results of finite element analysis, are applied. As a numerical example, the analysis results for a two-dimensional elasto-static problem, a plate with a crack, are presented and investigated.

• Journal of Plant Biotechnology
• /
• v.4 no.3
• /
• pp.123-127
• /
• 2002

Herbicide tolerant rice (Oryza sativa L. cv. Ilpumbyeo) cell lines were selected from $\gamma$-ray-irradiated anther-derived cell cultures. The anther-derived cell clusters were small (300 to 400 ${\mu}{\textrm}{m}$ in diameter) and uniform ones that were screened by miracloth filtering. The cell suspensions were very efficient to plate one layer onto agar medium and to screen target cell lines. Herbicide tolerant cell lines were selected by 5 mg/L cyhalofop butyl (CHB) treatment by using the small cell suspensions on agar N6 medium containing 1 mg/L 2,4-D and 0.2 mg/L kinetin. Of the cell lines, one line (CHB-1) showed stable tolerance at 10 mg/L concentration after 6-month culture without herbicide suspension. Growth stability of CHB-1 was similar to that of control cell line on 10 mg/L CHB containing medium. In this experiment we established herbicide tolerant cell line selection system by using anther-derived uniform-cell suspensions with $\gamma$-ray-irradiation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.125.1-125.1
• /
• 2010

A high efficiency polymer electrolyte membrane (PEM) fuel cell stack was developed for pressurized pure hydrogen and oxygen supplying conditions. The design objective for the cell stack was to maximize the electric efficiency and to minimize exhaust-gas emissions from it simultaneously. To achieve this objective, the cell stack was designed to use pure hydrogen and oxygen as fuel and oxidant, respectively, and to be operated under high gas inlet pressures and in a stage-wise dead-end operation mode. Major components constituting the cell stack, such as membrane electrode assembly, bipolar-plate, and gasket, have been developed to meet a target durability even in severe operating conditions: high gas inlet pressures and usage of pure oxygen. A high-power fuel cell stack was assembled using these components to verify the performance. The cell stack showed a good performance in terms of the efficiency and maximum power output.