• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.22-31
• /
• 1991

Machining with boring bars frequently induce chatter vibration because of the low stiffness and damping of cantilever shape of boring bars. To increase stiffness and damping, a carbon fiber epoxy composite boring bar was designed, manufactured and tested. The natural frequency of the carbon fiber epoxy composite boring bar in the free-free end condition was incerased more than 50% over that of the steel boring bar, and the damping of the carbon fiber epoxy composite boring bar was also increased 450%. The fundamental natural frequency of the carbon fiber epoxycomposite boring bar in the cantilever beam condition was found to be increased 20-30% over that of the steel boring bar in overhang length range 140-200mm. In machining S45C tapered workpieces, the limit of the overhang length of the steel boring bar was about 170mm in cutting speed 140m/min.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.197-207
• /
• 1998

전단변형 효과를 무시하는 경우에 비대칭 선형 변단면을 갖는 박벽 공간 보의 안정성 해석을 위한 일반이론을 유도한다. 비대칭 선형 변단면의 임의점을 통과하는 부재축과 단면의 주축의 방향과 무관하고 부재축과 직각을 이루는 두 개의 좌표축을 도입하여 직각좌표계를 정의한다. 정의된 좌표축을 기준으로 유한한 회전각의 2차항을 고려하는 변위장을 도입하여 연속체에 대한 가상일의 원리로부터 탄성변형에너지, 그리고 초기응력에 의한 포텐셜에너지를 유도한다. 이를 이용하여 비대칭 선형 변단면을 갖는 박벽 공간 보의 안정성해석을 위한 평형방정식을 제시한다. 3차 Hermitian 다항식을 변위파라미터의 형상함수로 사용하여 박벽 공간 보의 탄성강도 및 기하강도행렬을 상정할 뿐만 아니라, 단면의 좌표축에 상관없이 임의의 위치에 작용하는 하중에 대한 하중보정강도행렬(load-correction stiffness matrix)을 제시한다. 본 이론 및 방법의 타당성을 검증하기 위하여 수치해석을 수행하고 문헌의 결과 및 쉘요소를 사용한 해석결과와 비교하여 본 이론의 정당성을 입증한다.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.590-595
• /
• 2001

To improve the modeling accuracy for the finite element method, this paper proposes a method to make a combined use of finite elements and exact dynamic elements. Exact interpolation functions for a Timoshenko beam element are derived and compared with interpolation functions of the finite element method (FEM). The exact interpolation functions are tested with the Laplace variable varied. The exact interpolation functions are used to gain more accurate mode shape functions for the finite element method. This paper also presents a combined use of finite elements and exact dynamic elements in design problems. A Timoshenko frame with tapered sections is tested to demonstrate the design procedure with the proposed method.

• Smart Structures and Systems
• /
• v.32 no.3
• /
• pp.167-177
• /
• 2023

A probabilistic micromechanical framework is proposed to quantify numerically the self-healing capabilities of polymers containing microcapsules. A two-step self-healing process is designed in this study: A probabilistic micromechanical framework based on the ensemble volume-averaging method is derived for the polymers, and a hitting probability model combined with a crack nucleation model is then utilized for encountering microcapsules and microcracks. Using this framework, a series of parametric investigations are performed to examine the influence of various model parameters (e.g., the volume fraction of microcapsules, microcapsule radius, radius ratio of microcracks to microcapsules, microcrack aspect ratio, and scale parameter) on the self-healing capabilities of the polymers. The proposed framework is also implemented into a finite element code to solve the self-healing behavior of tapered double cantilever beam specimens.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.71-82
• /
• 2024

This paper proposes a new communication system for e-learning applications to mitigate the negative impacts of COVID-19 where the online massive demands impact the current commu-nications systems infrastructures and capabilities. The proposed system utilizes high-altitude platforms (HAPs) for fast and efficient connectivity provision to bridge the communication in-frastructure gap in the current pandemic. The system model is investigated, and its performance is analyzed using adaptive antenna arrays to achieve high quality and high transmission data rates at the student premises. In addition, the single beam and multibeam HAP radio coverage scenarios are examined using tapered uniform concentric circular arrays to achieve feasible communication link requirements.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.308-315
• /
• 2013

In this paper, Tapered slot antenna of IR-UWB was Designed and fabricated using HFSS and we suggest the beam width of the broadband antenna using group-delay and fidelity. For this purpose, acquired data from the Network Analyzer was analyzed in the time domain by using the chirp-Z transform and Simulation was conducted and confirmed with the CST microwave studio. Analysis of the antenna radiation pattern is the antenna separation at intervals of 0.5 metres and then transmit antenna is fixed and the receiving antenna 360 degree intervals of 10 degree each, The results of the analysis are as follows, and analyzer of the fidelity of the antenna's performance. An analysis of more than 90 percent of the cases is less than ${\pm}40$ degrees in good fidelity, more than 90% less than ${\pm}40$ degrees and lowe fidelity. In conclusion, Analysis of Beam width of wideband antenna with more precise is possible through using these radiation pattern using fidelity.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.101-107
• /
• 2003

In this study, we provide a single element log-periodic antenna that the feeding networks and array structures are aperture coupled and series dipole array type. We made the antenna for direct receiving the Moogoongwha satellite broadcasting signal. The transmission power was able to feed the patch dipole in series due to lay perpendicularly 8 series patch dipole on tapered slot. The patch dipole radiation pattern which fed in series power, make the main beam direction up $37^{\circ}{\sim}42^{\circ}$ within the BS/CS bandwidth. The main beam gain was measured 9.31~11.03 dBi. Using 32 elements to array the elements properly, we acquire $4{\times}8$ array structure on limited PCB board. As a result, it has been found that the new planar DBS antenna structure have high gain over 10dBi and acceptable elevation angle over 42 degree, and we can apply this result to commercial DBS reception antenna manufacturing.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6673-6678
• /
• 2015

Recently, the free form buildings are constructed frequently. Exterior and interior components of these buildings have the free cross-section and a curved shape. So, There are many usages of classical finite element having tapered section and free-style shape. Some general commercial applications like ETABS, SAP2000, MIDAS are usually used for the safety evaluation of the free form structures. However, there are some limits in the accuracy of structural analysis and the length of analysis time because a very complicated finite element mesh have to be used. Therefore, In this study, a pre and post program module was developed to take advantage of general 3-D curved beam element which has a free-style curved shape and mathematical backgrounds. Pre-post processing module has been developed in this study was developed to control the curvature of the curved members by the NURBS control points. As a result, fast geometric modeling than was possible commercial applications. In addition, realistic depiction of the shape and behavior patterns were possible because of the free-form building allows visual check of the free form.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.139-150
• /
• 2005

Finite element method is applied to the determinations of the two eigenvalues(the elastic critical load and the natural frequence of lateral vibrations) of single story-3 equal bay rectangular frame. The analysis parameters are taper parameter ${\alpha}$ for column, and beam span to column height ratio, ${\beta}$ and second moment area ratio of beam to column, ${\Upsilon}$. Support condition at the column base and sway condition at the column top are also considered in the stability analysis of frame. The changes in the coefficient of eigenvalue are represented by algebraic function of analysis parameter. The coefficients estimated by the proposed algebraic function show good agreement with those determined by finite element method, which suggest the design aid role of the proposed function. By increasing the column axial forces step by step, the corresponding frequencies are also determined, which makes one examine or confirm the relationship suggested by other studies.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.47-54
• /
• 2020

Integration of active and passive waveguides is an essential component of the photonic integrated circuit and its elements. Butt joint is one of the important technologies to accomplish it with significant advantages. However, it suffers from high optical loss at the butt joint junction and need of accurate process control to align both waveguides. In this study, we used beam propagation method to simulate an integrated device composed of a laser diode and spot size converter (SSC). Two SSCs with different mode properties were combined with laser waveguide and optical coupling efficiency was simulated. The SSC with larger near field mode showed lower coupling efficiency, however its far field pattern was narrower and more symmetric. Tapered passive waveguide was utilized for enhancing the coupling efficiency and tolerance of waveguide offset at the butt joint without degrading the far field pattern. With this technique, high optical coupling efficiency of 89.6% with narrow far field divergence angle of 16°×16° was obtained.