• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.289-292
• /
• 2009

In this paper, an optimum design center frequency proposes portable RFID reader antenna that is 920MHz frequency using the Taguchi's Method. Proposed antenna is cut corner of opposite angle and it's structure that have slots in four sides microstrip patch of a perfect square shape. This slot structure can miniaturize microstrip patch antenna and confirmed through an experiment that size of antenna about 18% decreases than structure that slot does not exist. Because compact antenna that have structure of slot changes according to complex design variables, analysis and experimental design for minimization of experiment number of times are required for optimum antenna design. In this research, designed antenna that have optimum structure when introduce and designs table of orthogonal arrays of the Taguchi's Method been experimental design that can minimize analysis and experiment number of times, achieve responsiveness analysis of main elements and analyzes the effect and minimizes design repeat with analysis result. Presented experiment result about antenna special quality that permittivity is 4.4 and manufactures to board of Epoxy 3.2T.

• Transactions of Materials Processing
• /
• v.19 no.3
• /
• pp.173-178
• /
• 2010

A die cast impeller blade has been developed in the effort on cost reduction in marine equipment industry. The purpose of this work is to optimize the die casting process using Taguchi's design of experiment for minimizing the internal defect of the die cast impeller blade. The experiments were preformed using the numerical simulation based on the L18 orthogonal array. As a results, the internal defect size of the die cast impeller blade for optimal design was controlled less than 1mm.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.3
• /
• pp.118-125
• /
• 1998

Chip control is a major problem in automatic machining process, especially in finish turning operation. In this case, chip breaker is one of the important factors to be determined. As unbroken chips are grown. these deteriorate the surface roughness. and proces automation can not be carried out. In this study to get rid of chip curling problem while turning internal hole. optimal chip breaker is selected from the experiment. The experiment is planned with Taguchi's method that is based on the orthogonal arrary of design factors. From the response table. cutting speed, feedrate, depth of cut and tool geometry turn to be major factors affecting chip formation. Then, optimal chip breaker is selected. and this is verified as good enough for chip control from the experiment.

• Proceedings of the Safety Management and Science Conference
• /
• 2000.05a
• /
• pp.265-273
• /
• 2000

A study to analyze and solve problems of polyacetal resin cutting experiment has presented in this paper. We have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/H ratio.

• IE interfaces
• /
• v.23 no.3
• /
• pp.257-263
• /
• 2010

Taguchi defined a good quality as 'A correspondence of product characteristic's expected value to the objective value satisfying the minimum variance condition.' For his good quality, he suggested Taguchi Method which is called Robust design which is irrelevant to the effect of these noise factors. Taguchi Method which has many success examples and which is used by many manufacturing industry. But Optimal solution of Taguchi Method is one among the experiments which is not optimal area of experiment point. On the other hand, Response Surface Method (RSM) which has advantage to find optimal solution area experiments points by approximate polynomial regression. But Optimal of RSM is depended on initial point and RSM can not use many factors because of a great many experiment. In this paper, we combine the Taguchi Method and the Response Surface Method with each advantage which is called Taguchi-RSM. Taguchi-RSM has two step, first step to find first solution by Taguchi Method, second step to find optimal solution by RSM with initial point as first step solution. We give example using catapults.

• Corrosion Science and Technology
• /
• v.20 no.2
• /
• pp.77-84
• /
• 2021

This study aims to optimize the DL-EPR test solution for duplex stainless steel S31083 using the Taguchi design. The test solution parameters applied to the Taguchi design are H₂SO₄, NaCl, KSCN concentration, and temperature. In the experimental design, an orthogonal array of 4 levels 4 factor L₁₆(4⁴) was used. Output values for the orthogonal array were used for resolution (degree of sensitization) and selective etch (I_a) values. The optimal test solution conditions were selected by comparing the normalized S/N ratio for the two reaction properties. As a result, the H₂SO₄ and NaCl were identified as the main factors influencing the sensitivity measurement, but the delta statistics showed that the KSCN concentration and temperature had relatively low influence. The optimal condition was identified as 1.5 M H₂SO₄+0.03 M KSCN+1.5M NaCl at 30 ℃. The degree of sensitization presented a tendency to depend on the heat treatment temperature and time in the optimal test solution. This investigation confirmed the possibility of optimizing the experiment solution for the DL-EPR test of stainless steel using the Taguchi technique.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.2
• /
• pp.167-176
• /
• 2000

A study to analyze and solve problems of plastic injection molding experiment has presented in this paper. We have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.277-280
• /
• 2008

Multi layer bellows are being manufactured for commercial vehicle because of the characteristic of high durability compared with single iaγor bellows used to passenger vehicle. Finite Element Method (FEM) study and optimization about single layer bellows are actively progressed, but FEM study about multi layer bellows which have gap between layer is rarely processed. Therefore, this article presents finite element modeling of multi layer bellows for the improvement of simulation reliability. For the shape optimization of multi layer bellows, design of experiment and Taguchi method are used.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.107-108
• /
• 2008

This article describes optimization for PGS(Patterned Ground Shield) of rectangular spiral inductor using Taguchi's Design of Experiment. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. Using taguchi's design of experiment, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• Journal of the military operations research society of Korea
• /
• v.27 no.1
• /
• pp.73-88
• /
• 2001

Designing high quality products and processes at a low cost is central technological and economic challenge to the engineer. The combination of engineering concepts and statistical implementations offered by Taguchi\`s off-line design technique has proven t be invaluable. By examining some deficiencies in designs from the Taguchi\`s highly fractional, orthogonal main effect plan based on orthogonal arrays, alternative method is proposed. The maximum resolution or the minimum aberration criterion is commonly used for selecting 2$^{n-m}$ fractional designs. We present new high resolution (low aberration) linear graphs to simplify the complexity of selecting designs with desirable statistical properties. The new linear graphs approach shows a substantial improvement over Taguchi\`s linear graphs and other related graphical methods for planning experiment. The new set of linear graphs will allow the experimenter to maintain the simple approach suggested by Taguchi while obtaining the best statistical properties of the resulting design such as minimum aberration as a by-product without dependency on complicated computational algorithm or additional statistical training.g.