• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.286-289
• /
• 2009

This paper deals with the experimental investigation of the steel cord straightening during the stranding process. The over-twisting and roller straightening process are essential to improve the product quality during the stranding process. To investigate the effectiveness of two processes, four experimental cases are constructed according to the use of an over-twister and two roller straighteners. Three assessment items, such as the residual torsion, the arc-height and the preforming ratio, are measured in each experimental case for the quantitative evaluation of a steel cord. The steel cord shape is also measured to investigate the variation of the straightness efficiently after passing through each process. Finally, the effectiveness of the over-twisting and the roller straightening process is explained based on the experimental results.

• Transactions of Materials Processing
• /
• v.9 no.6
• /
• pp.574-581
• /
• 2000

A vertically-walled auto-body part is one of the most difficult stamping parts because of angle change, wall curl, and twisting of the blank after springback as well as fracture and wrinkle. In this study, computational simulations of the vertically-walled auto-body part are carried out focusing on angle change, wall curl, and twisting after springback. Binderwrap blank shape is used in forming analysis for precise initial contacts between punch and blank. An adaptive mesh method is used in springback analysis for precise calculation of bending moments. In springback analysis, the differences of 2 and 3 dimensional analysis are compared and the effects of blank holdig force and friction coefficient are evaluated. In order to verify the validity of simulation results, they are compared with measured ones. The predicted thickness distribution and formed shape are agreed well with those of the measurement. The Predicted springback amount is less than that of the measurement.

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.4
• /
• pp.49-55
• /
• 2021

The Cable in Conduit Conductor (CICC) configurations are designed, tested and realized to make high field superconducting (SC) magnets. The evolution of CICC design makes it challenging to forecast thermo-hydraulic behavior. A common objective of thermo-hydraulic studies is to obtain the most reliable predictive correlation for friction factor in CICC geometries and to reduce the dependency on the experiment. So far, only the void fraction and Reynolds number have been considered in the predictive correlations in an explicit way. In the present paper, the CICC twisting pattern dependency, called tortuosity (τ), on the pressure drop prediction, has been assessed through a numerical simulation approach. The CICC twisting pattern with 6+1 petals (solid conductor in the present study) with different twisting pitches is mimicked in the numerical simulation for the range 100 ≤ Re ≤10000 and 1 < τ < 1.08 and a correlation for friction factor, f, has been proposed as a function of Re and τ.

• Textile Coloration and Finishing
• /
• v.12 no.2
• /
• pp.79-88
• /
• 2000

Draw textured yarns have many differences with yarn quality as well as wearing, due to the bulkiness, thermal and physical properties according to the false twist texturing system. In order to improve such property, many studies have been accomplished for developing good textured yarns and their fabrics, but these have been essentially obtained by experimental data or mathematical analysis. This study surveyed various properties of DTY produced by false twist texturing system, namely pin and crossed-belt false twist insertion systems. And 6 yarn specimens of 2 group(pin twisting type, belt twisting type) were measured and analysed.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.2
• /
• pp.151-156
• /
• 1994

The equations of motion of a submarine pipeline with the internal flowing fluid and subject to hydrodynamic loadings are derived by using Hamilton's principle. Coupling between the bending and the longitudinal extension due to axial load and thermal expansion are considered. Coupling between the twisting and extension are not considered. The equations of motion are well agreed with the results which are derived by the vector method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.2 s.150
• /
• pp.255-265
• /
• 2006

The purpose of this study was to examine the dyeing properties of four kinds of composite yams that were twisted in different processes. The composite yarns consist of acetate and functional polyester in ratio of 70 : 30. The composite yams were dyed at 100$^{circ}C$ and 125$^{circ}C$ using three types of dyes, disperse dyes for acetate fiber, PET fiber and PET-acetate blended fiber, in the three primary colors. The exhaustion($\%$) and K/S value were observed for each case. Also the effects of four different twisting processes to dyeing properties and physical properties were examined. Regardless of twisting methods, the composite yarns that were dyed at 125$^{circ}C$ had higher exhaustion($\%$) than those were dyed at 100$^{circ}C$ with all three types of dyes; However, tendency of the K/S value after reduction cleaning process was measured at 100$^{circ}C$ and the value measured 125$^{circ}C$ had a great difference with disperse dyes for acetate and dyes for PET. The difference of the K/S values of composite yarns, when dyed at 100$^{circ}C$ and 125$^{circ}C$ with disperse dyes for PET-acetate blended fiber, was almost negligible. According to twisting methods K/S values were in the following order: AP1 > AP3 > AP4> AP2. This means that AP1, treated at 220$^{circ}C$, had the highest K/S value and K/S value becomes higher as the yam is higher twisted and becomes lower as lower twisted. On the other hand, the dry shrinkage and wet shrinkage showed low shrinkage rate when the twist was high and steam setting temperature was high.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.524-530
• /
• 2015

Early wearable robotic devices were big, powerful and manipulator-like. Recently, various applications of wearable robotics have shown a greater demand for lower weight and compliancy. One approach to achieve these objectives is the use of novel actuators such as twisted string actuators. These actuator are very light, quiet, mechanically simple and compliant. Therefore, they can drastically decrease the weight and size of robotic systems such as exoskeletons. However, one drawback of this actuator is its nonlinear transmission ratio, which is established as a ratio between the angle of twisting of the strings and their resulting contraction. In this paper, we propose a transmission mechanism with rotational motion as the output incorporating a twisted string actuator (TSA). The designed mechanism allows the linearization of the relationships between the input and output displacements and forces of a TSA. The proposed design has been validated theoretically and through a set of computer simulations. A detailed analysis of the performance of the proposed mechanism is presented in this paper along with a design guideline.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.713-719
• /
• 2012

This paper deals with the natural frequency analysis and two experiments to evaluate first twisting and bending natural frequency of railway vehicle. The KS R 9228 testing method is generally performed as pseudo FRF(frequency response function) which is widely used by two accelerometers. The exciting method is utilized using the load weight(1 ton release). The modal testing is used to verify KS R 9228 testing result and the natural frequency analysis result. The first twisting and bending natural frequency should be above 10 Hz by resonance which is mostly generated between bogie and vehicle frame exciting low frequency. The first twisting and bending natural frequency of railway vehicle are successfully verified between analysis and test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.10
• /
• pp.803-810
• /
• 2009

Micromirrors have a wide range of applications such as optical switches, laser scanners, and digital projection displays. Due to their low performances and high costs, however, practical applications of micromirrors are quite limited. At present micromirrors demand not only a better design but also a simple fabrication process. In this study a twisting-type micromirror that can be driven by two thermal bimorph actuators bending in opposite directions is designed from electro-thermo-mechanical theories and fabricated through a simple MEMS process. Each actuator consists of $SiO_2$ and gold thin-film layers. Simplified analytical model has been built to optimize the performance of micromirror. Due to unexpected resistance increase of metal film and alignment mismatch during fabrication process, experimental rotation angles of micromirrors are about $11^{\circ}$ at applied voltages less than 0.6V. From numerical simulation and analytical studies, however, the next design can provide rotation angles over $20^{\circ}$ at the same applied voltage.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.124-127
• /
• 2004

In the previous experimental study about extrusion of circular product with four helical fins, it was known that product with helical fins may not to be rotated during extruding with rotating extrusion dies in spite of using twisted dies. According to the results of experiments with Plasticin material, it was anticipated that the extrusion load could be reduced if rotating dies could be used, because it needs high pressure in order to twist billet and form fin shape on the surface of product in the case of using conventional fixed helical dies. So, in this paper, according to the extrusion load analyzed by DEFORM-3D software, optimal rotational velocity of rotating dies can be obtained, and the twisting, angle of product can be analyzed during extruding product with helical fins in the case of two types of rotating of dies. The results of analysis by DEFORM-3D show that the twisting angle of product can be controlled by twisted angle of extrusion helical dies and the rotational velocity of helical dies.