• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.867_868
• /
• 2009

Interior permanent magnet synchronous motor [IPMSM] which has high power density is applied to motor for Hybrid electric vehicle[HEV], Electric vehicle[EV], Fuel cell electric vehicle[FCEV] and electric home appliances. In order to improve efficiency performance of IPMSM, this paper presented a study by making a hole around air barrier. Because concentrated rib stress is distributed by suitable hole, the hole can reduce rib thickness of IPM rotor. And it can help decrease PM[Permanent Magnet] leakage flux. Saliency ratio($L_q/L_d$) is also increased by magnetic circuit change. For this study, structure analysis of rotor is performed by Ansys program.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.289-292
• /
• 2002

A sensorless control of a PM synchronous motor under the parameter variation is presented. The rotor position is estimated by using the d-axis and q-axis current errors between the real system and motor model of the estimator. The stator resistance is measured at low speeds when the motor changes its rotating direction. The gains in the position estimator are also adapted according to the motor speeds.

• KIEE International Transactions on Power Engineering
• /
• v.3A no.3
• /
• pp.161-167
• /
• 2003

This paper presents a study performed to investigate the steady-state operational strategies of UPFCs in the Jeollanam-Do system in Korea. The objective of the study was to determine the UPFC operating points under normal and contingency conditions. The study consists of developing load flow models to simulate different load levels with and without UPFCs in the system, assessing the effectiveness of UPFCs by contingency analysis, and introducing optimal corrective actions for removing voltage problems caused by contingencies. The paper describes analytical tools, models and approach. It also includes analysis and discussion of the study results. The paper contributes to the area of transmission operational studies with FACTS applications.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1167-1171
• /
• 1992

A predictive current control in the synchronous reference frame with the back EMF estimation using the previous voltages and currents is proposed. To reduce the torque ripple produced by harmonics in the air gap flux, the q-axis current is compensated using the estimated torque constant. The effectiveness of the proposed control is compared to the conventional control scheme through the simulation.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2344-2353
• /
• 2018

A coupled recursive total least squares (CRTLS) algorithm is proposed for parameter estimation of permanent magnet synchronous machines (PMSMs). TLS considers the errors of both input variables and output ones, and thus achieves more accurate estimates than standard least squares method does. The proposed algorithm consists of two recursive total least squares (RTLS) algorithms for the d-axis subsystem and q-axis subsystem respectively. The incremental singular value decomposition (SVD) for the RTLS obtained by an approximate calculation with less computation. The performance of the CRTLS is demonstrated by simulation and experimental results.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1004-1011
• /
• 2016

The inaccurate model parameters in the predictive current control of surface-mounted permanent magnet synchronous motor (SMPMSM) affect the current dynamic response and steady-state error. This paper presents a model parameter correction algorithm based on the relationship between the errors of model parameters and the static errors of dq-axis current. In this correction algorithm, the errors of inductance and flux are corrected in two steps. Resistance is ignored. First, the proportional relations between inductance and d-axis static current errors are utilized to correct the error of model inductance. Second, the flux is corrected by utilizing the proportional relations between flux and q-axis static current errors under the condition that inductance is corrected. An experimental study with a 100 W SMPMSM is performed to validate the proposed algorithm.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.159-162
• /
• 2001

This paper is proposed an efficiency optimization operation algorithm for synchronous reluctance motor (SynRM) using current phase angle control technique. The SynRM has to controlled with the optimal current phase angles with load and operation speed variation, to obtain high efficiency over the wide speed ranges. An efficiency optimization condition in SynRM which minimizes the copper and iron losses is derived based on the equivalent circuit model of the machine. The objective of the efficiency optimization control algorithm compensating the optimum current angle, is to seek a combination of d and q-axis current components which provides minimum losses at a certain operating point in steady state. The usefulness of the proposed efficiency optimization control is verified through vector-controlled inverter system with the SynRM.

• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.396-404
• /
• 2010

This paper presents simple schemes used to estimate the initial rotor position and the d- and q-axis inductances for effective Maximum Torque per Ampere (MTPA) operation in a wind-power system using an IPMSM (Interior Permanent Magnet Synchronous Machine). An IPMSM essentially requires an exact coordinate transformation and accurate inductance values to use a reluctance torque caused by the saliency characteristic. In the proposed high-frequency voltage testing method, there is no voltage drop caused by the resistance and the electromotive force. The initial rotor position and the inductance can be measured through an analysis of the stator current without turning the rotor. The experimental results are presented in order to illustrate the feasibility of the proposed method.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1224-1234
• /
• 2019

Hybrid rotor position estimation methods that integrate a fundamental model and high frequency (HF) signal injection are widely used for the wide speed-range sensorless control of interior permanent-magnet synchronous machines (IPMSMs). However, the direct transition of two different schemes may lead to system fluctuations or system instability since two estimated rotor positions based on two different schemes are always unequal due to the effects of parameter variations, system delays and inverter nonlinearities. In order to avoid these problems, a seamless transition strategy to define and construct a virtual q-axis inductance is proposed in this paper. With the proposed seamless transition strategy, an estimated rotor position based on a fundamental model is forced to track that based on HF signal injection before the transition by adjusting the constructed virtual q-axis inductance. Meanwhile, considering that the virtual q-axis inductance changes with rotor position estimation errors, a new observer with a two-phase phase-locked loop (TP-PLL) is developed to accurately obtain the virtual q-axis inductance online. Furthermore, IPMSM sensorless control with maximum torque per ampere (MTPA) operations can be tracked automatically by selecting the proper virtual q-axis inductance. Finally, experimental results obtained from an IPMSM demonstrate the feasibility of the proposed seamless transition strategy.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.12
• /
• pp.1865-1874
• /
• 2013

In this paper, a design method of speed and position estimator based on unscented Kalman filter is proposed for the no sensor control of IPMSM(Interior Permanent Magnet Synchronous Motor). The proposed method is simple more than the estimator designed with rotation axis for current measurement. Also the proposed state estimator is designed including nonlinear terms of the estimator. The controller which constructed using nonlinear back-stepping control method is operated speed and current control using the estimated speed and currents information. Through simulation, the performance of the designed estimator is compared to the estimator which is designed to synchronize d-q axis.