• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.8
• /
• pp.902-913
• /
• 1992

There have been several control schemes for the single input systems with unmeasurable state variables using variable structure control(VSC) theory. In the previous VSC, the systems must be represented in phase canonical form and the complete measurements for each state variable must be assumed. In order to eliminate these restrictions several VSC methods were proposed. And especially for the systems in phase canonical form with unmeasurable state variables, the reduced order switching function algorithm was proposed. But this method has many drawbacks and can not be used in the case of general form (not phase canonical form) dynamic system. Therefore this paper propose new construction method of switching fuction for the systems in phase canonical form, which reduce the restriction of reduced order switching function algorithm. And this algorithm can be realized for any state representation and adopted in the systems where not all states are available for switching function synthesis or control.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.919-927
• /
• 2013

This paper proposes a Boundary Current Mode (BCM) control scheme to realize soft switching on a conventional single phase full bridge DC/AC inverter. This technique with the advantages of no auxiliary components, low cost, high efficiency, and simple in control, is attractive for micro-inverter applications. The operation principle and characteristic waveforms of the proposed soft switching technique are analyzed in theory. A digital controller is provided based on that theory. To balance the requirements of efficiency, switching frequency, and inductor size, the design considerations are discussed in detail to guide in BCM inverter construction. A 150W prototype is built under these guidelines to implement the BCM control scheme. Simulation and experiment results demonstrate the feasibilities of the proposed soft switching technique.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.2
• /
• pp.181-184
• /
• 2017

This study analyzes the turn-on and turn-off transients of a metal-oxide-semiconductor field-effect transistor (MOSFET) with high-switching frequency systems. In these systems, the voltage distortion becomes serious at the output terminal of a Vienna rectifier by the turn-off delay of the MOSFET. The current has low-order harmonics through this voltage distortion. This paper describes the transient of the turn-off that causes the voltage distortion. The algorithm for reducing the sixth harmonic using a proportional-resonance controller is proposed to improve the current distortion without complex calculation for compensation. The reduction of the current distortion by high-switching frequency is verified by experiment with the 2.5-kW prototype Vienna rectifier.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.643-645
• /
• 1999

In experiment, a real inverted pendulum system has state constraints and limited amplitude of input. These problems make it difficult to design a swing-up controller. To overcome these problems, we design a sliding mode controller considering physical behaviour of the inverted pendulum system. This sliding mode controller uses a switching control action to converge along a specified path derived from energy equation from a state around the path to desired states(standing position). And optimal control method is used to guarantee stability at unstable equilibrium position. The designed controller can be applied to all inverted pendulum systems regardless of the values of their parameters. Compared with previous existing controllers, it is simple and easy to tune. Experimental results are given to show the effectiveness of this controller.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.60-67
• /
• 1998

In this paper, a gain scheduling method of PID controller is proposed using fuzzy logic for balancing control of an inverted pendulum. First, gains of PID controller are calculated using pole-placement technique for the linearized model of an inverted pendulum and these gains are modified by fuzzy logic throughout control operations. A PD controller is used by switching near the set-point to improve the performance. It is illustrated by simulations that the proposed hybrid fuzzy control method yidels smaller rising time and overshoot compared to the fixed-gain PID controller or fuzzy logic-based only PID controller.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.179-184
• /
• 2008

This paper presents the design of the feed forward controller to improve on the non-interference control performance of a single PWM converter in parallel for high-speed trains. The feed forward controller is designed to minimize the interference generated by converter switching in parallel operation of PWM converters. The gain value of the feed forward controller is calculated by inductance values of the input transformer. However, it is difficult to decide this gain value exactly because inductance values are changed by the operation condition of an input transformer. In this paper, the proposed design of feed forward controller can exactly decide the gain value using the leakage inductances estimated by detecting the variation of input current. the validity of the proposed feed forward controller is proved through the simulation results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.10
• /
• pp.1029-1038
• /
• 2009

This paper proposes a gain switching algorithm for joint position control of a hydraulic humanoid robot. Accurate position control of the lower body is one of the basic requirements for robust balance and walking control. Joint position control is more difficult for hydraulic robots than it is for electric robots because of an absence of reduction gear and better back-drivability of hydraulic joints. Backdrivability causes external forces and torques to have a large effect on the position of the joints. External ground reaction forces therefore prevent a simple proportional-derivative (PD) controller from realizing accurate and fast joint position control. We propose a state feedback controller for joint position control of the lower body, define three modes of state feedback gains, and switch the gains according to the Zero Moment Point (ZMP) and linear interpolation. Dynamic equations of hydraulic actuators were experimentally derived and applied to a robot simulator. Finally, the performance of the algorithm is evaluated with dynamic simulations.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.11
• /
• pp.619-623
• /
• 2004

We proposed the bridge type superconducting fault current limiter(SFCL) using switching operation of high-Tc superconducting(HTSC) thin film. The proposed bridge type SFCL consists of HTSC thin film, a diode bridge and a dc reactor. The controller for the operation of an interrupter is required in the conventional bridge type SFCL to prevent the continuous increase of fault current after a fault happens. On the other hand, the proposed bridge type SFCL can limit the fault current without the interrupter and the controller for its operation by the resistance generated when the gradually increased fault current exceeds HTSC thin film's critical current. We calculated the time when the gradually increased fault current started to be limited by the resistance generated in HTSC thin film after a fault happened and confirmed that it could be dependent on the amplitude of source voltage. The experimental results well agreed with the calculated ones from simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.8 s.179
• /
• pp.1899-1909
• /
• 2000

This paper proposes a new $H_{\infty}$ yaw moment control scheme using brake torque switching for improving vehicle performance and stability especially in high speed driving. In the scheme, one wheel is selected, depending on the vehicle states, at which a brake torque for control is applied. Steering angles are modeled as a disturbance to the system and the $H_{\infty}$ controller is designed to minimize the difference between the performance of the vehicle and that of the desired model. Its performance robustness as well as stability robustness to system parameter variations is assured through ${\mu}$-analysis. Various simulations with a nonlinear 8-DOF vehicle model show that proposed controller enhances the vehicle performance and stability under disturbances and parameter variations as well as under the normal driving condition.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.1
• /
• pp.97-103
• /
• 2013

This paper describes the characteristics of Electronic Throttle Controller (ETC) module in BLDC motor without the hall sensor for detecting a rotor position. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analogue voltage output on the throttle valve instead of BLDC motor for detecting the rotor position. So the additional commutation information is necessarily needed to control the ETC module. For this, the estimation method is applied. In order to improve and obtain the high resolution for the position control, it is generally needed to change the gear ratio of the module or the electrical switching method etc. In this paper, the 3-phase switching between successive commutations is adapted instead of the 2-phase switching that is conventionally used. In addition, the position control with a variable PI gain is applied to improve a dynamic response during a transient period and reduce vibration at a stop in case of matching position reference. The mentioned method can be used to estimate the commutation state and operate the high-precision position control for the ETC module and the high response characteristics. The validity of the proposed method is examined through the experimental results.