• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.136-139
• /
• 2001

The voltage resonating inverter has a defect in the switching element that works at 5 or 6 times higher than input voltage. Especially, it is very difficult to choose very high switching device for the 220[V]commercial voltage. In this paper, it is proposed the optimum method to realize the turbo 2000[W] power for induction cooker that is employed the 900[V] IGBT with decreasing operating voltage of the switching component by making the 220[V], 1500[W] inverter through the clamp mode voltage resonating inverter.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.1
• /
• pp.43-48
• /
• 2004

This paper deals with design and fabrication of heater-triggered switching system for the high-Tc superconducting (HTS) power supply with series-connected double-pancake load. Amongst all components, heater triggering is the most important element for the performance of HTS power supply. To fabricate the optimal heater-triggered system, its characteristics have been analysed through the simulation and expriment. The thermal analysis of switching parts of the Bi-2223 solenoid according to the heater input was carried out. Based upon the analysis, 8A electromagnet current and 1.5A DC Heater current were optimally derived, and 8s and 20s for the pumping period were selected in this experiment. In the experiment. the maximum pumping current reached about 24A with Bi-2223 pancake load of 6mH.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.901-903
• /
• 2001

This paper studies the influences of the magnetic radial forces on the vibrations of the Switched Reluctance Motor(SRM). The effects of changing the switching angle on the magnetic forces is analyzed by Finite Element Analysis. Theoretical and several experimental results explain clearly the origins of vibrations caused by radial magnetic forces and current.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.702-704
• /
• 2001

This paper investigates efficiency and power factor of Switched Reluctance Motor (SRM) using Finite Element Method considered driving circuit. The efficiency and power factor are calculated in Input terminal and Output terminal respectively. When calculating power factor, apparent power is obtained by effective voltage and current because SRM is operated by switching of driving circuit. Efficiency is calculated by mechanical output and active power. Finally, the characteristics of efficiency and power factor in three proposed models are compared due to the switching pattern.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.1
• /
• pp.14-20
• /
• 1998

The resistive shunting for the fine control of a Direct Energy Transfer(DET) systems is fully developed, but the non-resistive shunting using variable size solar array segments is in progress. This paper presents the spacecraft power control through switching of solar array segments, which uses a fully regulated DET power regulation. This method eliminates a dissipative element and removes the associated design limitations which arise from the dissipative elements for radiating cooling in deep space. The switching shunt regulator comprises the switched Solar Array Shunt(SAS) modules that regulate the solar array power. These SAS modules connect/disconnect the solar array segments to/from the bus according to the loading in the main bus without significant variations in the dissipation level. In this paper, twelve segments are used in the shunting. In order to verify the basis of analysis, the computational result of an analytic loop gain is performed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.186-192
• /
• 2002

In this paper, interleaved boost power factor corrector(IBPFC) is applied as a pre-regulator in switch mode power supply. IBPFC can reduce input current ripple and effectively increase the switching frequency without increasing the switching losses, because input current is divided each 50% by two switching devices. IBPFC can be classified as three cases by duty ratio condition in continuous current mode and be carried out state space average modeling. According to the modeling, steady and transient state analysis is performed by steady elements and perturbation element. Control transfer function is derived for design of control system.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.647-656
• /
• 2015

This paper proposes a single-RF MIMO receiver that adopts a beam-switching antenna (BSA) instead of a conventional array antenna. The beauty of the proposed single-RF MIMO receiver with BSA is that it can be deployed in a very small physical space while achieving a full spatial multiplexing gain. Our analysis has revealed that the use of a BSA inevitably results in the spectrum spreading effect at the RF output, which in turn causes an SNR decrease and adjacent channel interference (ACI). Two novel receiver techniques are proposed to mitigate the issues of redundant sub-band suppression and ACI avoidance. Numerical analysis results verify the performance improvement from the proposed receiver techniques.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.205-207
• /
• 2001

In response to this inverter microwave oven has been developed to improve high speed cooking time & energy saving performance. The voltage resonating inverter has a defect in switching element that works at 5 or 6times higher than input voltage. Especially, it is very difficult to choose the switching device is very high for the 220 (V) commercial voltage. In this paper, it is proposed the optimum method to realize the turbo 1200(W) output power for microwave oven that is employed the 900(V) IGBT with decreasing operating voltage of the switching component by making the 220(V), 1000(W) inverter through the active clamp voltage resonating inverter.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.331-334
• /
• 2001

The voltage resonating inverter has a defect in switching element that works at 5 or 6times higher than input voltage. Especially, it is very difficult to choose the switching device is very high for the 220(V)commercial voltage. In this paper, it is proposed the optimum method to realize the turbo 2000(W) power for induction cooker that is employed the 900(V) IGBT with decreasing operating voltage of the switching component by making the 220(V), 1500(W) inverter through the claim mode voltage resonating inverter.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1151-1153
• /
• 2003

In this paper, switching surge voltage distribution in stator windings of induction motor driven by IGBT PWM inverter is studied. To analyze the irregular voltage of stator winding, equivalent circuit model of inverter-cable-motor was proposed and high frequency parameter is computed by using finite element method (FEM). Electromagnetic transient program (EMTP) analysis of the whole system for induction motor and PWM inverter is proposed. In order to experiment, an induction motor, 380 [V], 50 [HP], with taps from one phase and a switching surge generator was built to consider the voltage distribution.