• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.8
• /
• pp.2033-2042
• /
• 1996

In this papre, we describe a recently implemented echo canceller for digital cellular communication of Code Division Multiple Access(CDMA) that features time sharing of digital signal processor(DSP) over four channels in one DSP to reduce per channel costs. In the Public Land Mobile Network(PLMN), it is important to cancel the echo reflected from the Public Switched Telephone Network(PSTN) side. In case of digital mobile system, the round-trip delay of the echo is in excess of about 180 milliseconds due to frame-by-frame voice coding. It is necessary to cancel the echo in PLMN. We have developed a multi-channel echo canceller tht operates with Time Switch Module in a Mobile Switching Center(MSC). The general echo canceller needs PCM trunk interface circuits and the tone detection and disabling circuits, but the multi-channel echo canceller linked with Time Switch Module does not need them. Therefore we could develop the effective and economical echo canceller.

• Journal of information and communication convergence engineering
• /
• v.9 no.1
• /
• pp.74-77
• /
• 2011

PSPICE modeling of a commercial LED driver IC (TOP245P) and PC817A optocoupler is proposed for the switch-mode power supply (SMPS) (applicable to LED driver) design and simulation. An analog behavioral model of the TOP245P IC including the shunt regulator, under-voltage(UV) detection, over-voltage(OV) shut-down and SR flip-flop is developed by using PSPICE. The empirical equation of PC817A current transfer ratio (CTR) is fitted from the datasheet of PC817A. Two types of SMPSs are simulated with the averaged-model and switching-model. The simulation results by the proposed PSPICE models are in good agreement with those in the data sheet and an experimental data.

• Journal of Sensor Science and Technology
• /
• v.19 no.4
• /
• pp.320-327
• /
• 2010

In this paper, electrostatically actuated direct contact type RF MEMS switches have been designed and demonstrated. As driving structures of the switch, cantilever, bridge, and torsion spring beam structures are used and the actuation voltage characteristics of the switches have been compared and discussed. The designed RF switches are fabricated with the surface micromachining technology using the electroplated gold and nickel structures. The characteristics of the fabricated switches are measured and analyzed. The switch, which is fabricated using the 510 ${\mu}m$-length bridge structure with the thickness of 1.5 ${\mu}m$, is actuated with 15 V driving voltage. The insertion losses are less than 0.2 dB over the measured frequency ranges from 0 to 20 GHz and the isolations are more than 30 dB.

• The KIPS Transactions:PartC
• /
• v.9C no.1
• /
• pp.65-72
• /
• 2002

In this paper, we implement a high-speed swatch tilth the function for label integration to enhance the expansion of networks using the label space of routers efficiently on MPLS over ATM networks. We propose an appropriate hardware structure to support the VC-merge function and differentiated services simultaneously. In this paper, we use the adaptive congestion control method such as EPD algorithm in carte that there is a possibility of network congestion in output buffers of each core LSR. In addition, we justify the validity of the proposed VC-merge method through simulation and comparison to conventional Non VC-merge methods. The proposed VC-merge capable switch is modeled in VHDL. synthesized, and fabricated using the SAMSUNG 0.5um SOG process.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.129-133
• /
• 2016

Theoretical and graphical analysis of pull-in-voltage and figure of merit for a fixed-fixed capacitive Micro Electromechanical Systems (MEMS) switch is presented in this paper. MEMS switch consists of a thin electrode called bridge suspended over a central line and both ends of the bridge are fixed at the ground planes of a coplanar waveguide (CPW) structure. A thin layer of dielectric material is deposited between the bridge and centre conductor to avoid stiction and provide low impedance path between the electrodes. When an actuation voltage is applied between the electrodes, the metal bridge acquires pull in effect as it crosses one third of distance between them. In this study, we describe behavior of pull-in voltage and figure of merit (or capacitance ratio) of capacitive MEMS switch for five different dielectric materials. The effects of dielectric thicknesses are also considered to calculate the values of pull-in-voltage and capacitance ratio. This work shows that a reduced pull-in-voltage with increase in capacitance ratio can be achieved by using dielectric material of high dielectric constant above the central line of CPW.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.3
• /
• pp.146-152
• /
• 2015

In this paper, we propose a boost DC-DC converter using a modification of the passive auxiliary resonant snubber circuit with a DC-DC converter in a typical active auxiliary resonant snubber-bridge inverter. The proposed boost DC-DC converter is small compared to the DC-DC converter according to the soft-switching scheme that requires a general auxiliary switch by realizing the soft switching operation as a DC-DC converter which does not require an auxiliary switch. It is light-weight, switch the turn-on and turn-off switching loss at the time of the superposition of the voltage and current is extremely small, so small. And the reduction of the surge voltage and current of the switch. In addition, the proposed boost DC-DC converter has a high efficiency over a wide load characteristics change area than conventional hard switching PWM boost converter using an RC snubber loss.

• ETRI Journal
• /
• v.30 no.4
• /
• pp.526-534
• /
• 2008

This paper presents a fully integrated 0.13 ${\mu}m$ CMOS MB-OFDM UWB transmitter chain (mode 1). The proposed transmitter consists of a low-pass filter, a variable gain amplifier, a voltage-to-current converter, an I/Q up-mixer, a differential-to-single-ended converter, a driver amplifier, and a transmit/receive (T/R) switch. The proposed T/R switch shows an insertion loss of less than 1.5 dB and a Tx/Rx port isolation of more than 27 dB over a 3 GHz to 5 GHz frequency range. All RF/analog circuits have been designed to achieve high linearity and wide bandwidth. The proposed transmitter is implemented using IBM 0.13 ${\mu}m$ CMOS technology. The fabricated transmitter shows a -3 dB bandwidth of 550 MHz at each sub-band center frequency with gain flatness less than 1.5 dB. It also shows a power gain of 0.5 dB, a maximum output power level of 0 dBm, and output IP3 of +9.3 dBm. It consumes a total of 54 mA from a 1.5 V supply.

• The Journal of Information Systems
• /
• v.30 no.4
• /
• pp.43-69
• /
• 2021

Purpose Although companies occupied the network market take the advantageous position first and can be successful in securing users over a certain size, it is important to satisfy the customers' demand and prevent the outflow of users toward a new alternative SNS. What is more, there are frequent changes in the flow of users toward new SNSs. Despite these dynamic market circumstances, there is a lack of research to explain the switching behaviors of SNS users. Design/methodology/approach The objective of this study is to explain and verify a specified migration theory(Push-Pull-Mooring model) focused on SNS fatigue in the psychological point of view, as well as reviewing previous studies on functional and technical characteristics of SNSs themselves. Moreover, this study tried to highlight factors affecting users actual SNS switch rather than their switching intention. Findings According to the statistical analysis, the most influenced pull factor to switch SNS was the alternative attractiveness. On the other hand, undesired relationship burden, service innovation and important mooring factors to prevent users' SNS switch. This study has a significant contribution to the theory, which analyzed users' actual SNS switch, and examined SNS users' psychological factors(SNS fatigue), reviewing the characteristics of existing services. To secure more users and to keep them, companies providing social network service need to develop differentiated strategies by analyzing psychological characteristics of various users.

• Journal of electromagnetic engineering and science
• /
• v.6 no.2
• /
• pp.135-145
• /
• 2006

This paper presents the theory, design, fabrication and characterization of the novel low actuation voltage capacitive shunt RF-MEMS switch using a corrugated membrane with HRS MEMS packaging. Analytical analyses and experimental results have been carried out to derive algebraic expressions for the mechanical actuation mechanics of corrugated membrane for a low residual stress. It is shown that the residual stress of both types of corrugated and flat membranes can be modeled with the help of a mechanics theory. The residual stress in corrugated membranes is calculated using a geometrical model and is confirmed by finite element method(FEM) analysis and experimental results. The corrugated electrostatic actuated bridge is suspended over a concave structure of CPW, with sputtered nickel(Ni) as the structural material for the bridge and gold for CPW line, fabricated on high-resistivity silicon(HRS) substrate. The corrugated switch on concave structure requires lower actuation voltage than the flat switch on planar structure in various thickness bridges. The residual stress is very low by corrugating both ends of the bridge on concave structure. The residual stress of the bridge material and structure is critical to lower the actuation voltage. The Self-alignment HRS MEMS package of the RF-MEMS switch with a $15{\Omega}{\cdot}cm$ lightly-doped Si chip carrier also shows no parasitic leakage resonances and is verified as an effective packaging solution for the low cost and high performance coplanar MMICs.