• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.3180-3186
• /
• 2011

A segmented scissors type switch has been developed for the urban transit maglev demonstration line to be commercialized near Incheon International Airport in 2013. Based on the design of the previous segmented 3-way switch, the scissors switch is composed of four segmented 2-way switches up/down and left/right and a turn table in the mid point. The main function of the scissors switch is to change the running direction of the train at end terminals. The developed scissors switch is planned to be installed in front of the 102 station, which has a side platform, of the demonstration line. The total length of the switch is 65m and the distance between the up and down track centerlines is 6m. The 2-way switches and turn table are made of steel box type beams, and have their own driving unit, locking unit, control unit, levitation and propulsion rails, and so on. Installed in the factory, a 100,000-cycle continuous operation test was carried out after manual and automatic test operations. The applicapability of the developed switch was verified through the measurements of the linearity of the track after repetitive operations, the mechanical operation noise, the load of the main driving motor, the safety of the control panel, the natural frequency of the girder, the deformation of the girder, and so on.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.760-767
• /
• 2014

This paper describes a high-radix crossbar switch design with low latency and power dissipation for Network-on-Chip (NoC) applications. The reduction in latency and power is achieved by employing a folded-clos topology, implementing the switch organized as three stages of low-radix switches connected in cascade. In addition, to facilitate the uniform placement of wires among the sub-switch stages, this paper proposes a Mux-Matrix-Mux structure, which implements the first and third switch stages as multiplexer-based crossbars and the second stage as a matrix-type crossbar. The proposed 256-radix, 8-bit crossbar switch designed in a 65nm CMOS has the simulated power dissipation of 1.92-W and worst-case propagation delay of 0.991-ns while operating at 1.2-V supply and 500-MHz frequency. Compared with the state-of-the-art designs in literature, the proposed crossbar switch achieves the best energy-delay-area efficiency of $0.73-fJ/cycle{\cdot}ns{\cdot}{\lambda}^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1849-1854
• /
• 2010

As for information system in hospital which digital hospital aims at, there are PACS(Picture Archiving and Communication System) and soon. PACS transfer and store various medical pictures which are occurring in hospital. The various medical pictures is captured by using keyboard or foot switch during a surgical operation. In this paper, foot switch USB module that can be mounted into a main foot switch case is designed and implemented, it is having a MCU circuit with a built-in micro-controller and a I/O interface having a maximum of five switch. we also developed foot switch control software program with various functions. The result of using the module in the hospital field confirms that the module operates safely.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2173-2175
• /
• 1999

This paper presents the development of closing switch for high voltage and current in detail. Design concept of INPIStron triggered by the gas puffing, voltage hold-off, current capacity, insulating and electrode material, rise time etc, are described. Also for the dptimized design of the electrical triggering switch, pin, ring, wire brush, surface discharge and HCP(Hypo-Cycloidal Pinch) trigger are considered.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1978-1979
• /
• 2007

In this paper, the authors introduce a high-speed microprocessor based on automatic vacuum capacitor switch with a modified digital filter design using distributed arithmetic. The automation trends particularly the automatic vacuum capacitor switch has helped ameliorate the power factor essentials and automatically triggered to close when the line current exceeds rated value. Microprocessor relays use digital filters to extract only the fundamental and attenuate harmonics. To provide optimum speed characteristics a distributed arithmetic based filter design in the microprocessor controller which not only enhances filtering speed but additionally enables lower power consumption at the cost of area has been introduced. The result is a unified description that describes a digital filter structure down to bit level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.744-749
• /
• 2016

This paper presents the design of a computer-generated hologram for beam control of an LCOS-based wavelength selective switch, which is the core technology for next-generation ROADM. By introducing a computer-generated hologram instead of general grating patterns to control the LCOS device, we contribute to building a more efficient wavelength selective switch. With the use of phase modulation properties of LCOS devices, we designed the hologram for five-port output and a 40-channel wavelength selective switch. We applied a multi-level phase modulation technique with the Gerchberg-Saxton algorithm to produce the hologram, which is easily scalable to any different type of wavelength selective switch. With an experimental setup, we verified the usability of the hologram designed for five-port output. We also suggest a hologram design technique for beam control of a 40-channel wavelength selective switch.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.261-269
• /
• 2016

A high-performance transmit/receive (T/R) switch is essential for every radio-frequency (RF) device. This paper proposes a T/R switch that is designed in the CEDEC 0.13 μm complementary metal-oxide-semiconductor (CMOS) technology for 2.4 GHz ISM-band RF applications. The switch exhibits a 1 dB insertion loss, a 28.6 dB isolation, and a 35.8 dBm power-handling capacity in the transmit mode; meanwhile, for the 1.8 V/0 V control voltages, a 1.1 dB insertion loss and a 19.4 dB isolation were exhibited with an extremely-low power dissipation of 377.14 μW in the receive mode. Besides, the variations of the insertion loss and the isolation of the switch for a temperature change from - 25℃ to 125℃ are 0.019 dB and 0.095 dB, respectively. To obtain a lucrative performance, an active inductor-based resonant circuit, body floating, a transistor W/L optimization, and an isolated CMOS structure were adopted for the switch design. Further, due to the avoidance of bulky inductors and capacitors, a very small chip size of 0.0207 mm² that is the lowest-ever reported chip area for this frequency band was achieved.

• Journal of the Korean Society of Safety
• /
• v.37 no.1
• /
• pp.12-19
• /
• 2022

Circuit breakers are a crucial factor in ensuring the safety of a Direct Current (DC) grid. One type of DC circuit breaker, the Z-source DC circuit breaker (ZCB), uses a thyristor, which is a type of semiconductor switch. In the event of a fault in the circuit, the ZCB isolates the fault by generating a zero crossing current in the thyristor. The thyristor quickly and actively isolates the fault while generating a zero crossing current, but thyristor switch cannot control turn-off and the allowable current is lower than the current of the mechanical switch. Therefore, it is best to use a mechanical switch with a high allowable current capacity that is capable of on/off control. Due to the slow reaction time of mechanical switches, they may not isolate the fault during the zero crossing current time interval created by the existing circuit. In this case, the zero crossing current time can be increased by using the property that hinders the rapid change in the current of the inductor. This paper will explore whether adding system inductance to increase the zero crossing current time interval is a solution to this problem. The simulation of changing inductor and capacitor (LC) of the circuit is repeated to find an optimal change in the zero crossing current time according to the LC change and provides an inductor and capacitor range optimized for a specific load. The inductor and capacitor range are expected to provide optimization information in the form LC values for future applications of ZCB's using a mechanical switch.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.12
• /
• pp.679-684
• /
• 2000

Closing switch, key component of pulsed power system, is constructed simply and used frequently due to the easy control and manufacture of one. The kind of one are spark-gap, triggered vacuum switch, pseudo-spark switch and INPIStron. But the electrode of spark gap switch is damaged with the hot spot by Z-pinch and then the life of one become short. INPIStron with inverse pinch effect has long life but it is difficult trigger system to provide uniform discharge between cathode and anode. In this paper, the design and manufacturing of INPIStron with gas puffing trigger method in order to supply uniform discharge inter-electrode and the performance of the developed INPIStron applied to 500[kA]-2[MJ] pulsed power system is presented.

• The KIPS Transactions:PartC
• /
• v.8C no.4
• /
• pp.389-396
• /
• 2001

기존의 라우터 기반의 패킷 스크리닝 방식은 ATM 네트워크 상에서는 패킷 수준의 스크리닝 기능의 적용을 위하여 SAR(Segmentation And Reassembly) 과정을 필요로 하기 때문에 고속의 셀 처리를 수행하는 ATM Switch의 셀 처리 속도를 저하시킨다는 문제점을 안고 있다. 본 논문에서는 셀 스크리닝 방식에 기반한 병렬 처리 구조의 ATM Firewall Switch를 제안한다. 제안된 Enhanced ATM Firewall Switch는 셀 단위로 분할된 패킷의 1, 2번 셀들에 대한 검사만을 통하여 스크리닝 기능을 수행하기 때문에 셀 단위의 스크리닝 수행이 가능하며, 정책 캐쉬의 도입을 통해 셀 스크리닝 수행속도를 향상하였다. 또한 독립적인 User Cells Filter 기능 블록의 설계를 통하여 병렬 처리 구조의 셀 스크리닝 수행이 가능하도록 구성하여 셀 지연 시간을 최소화하였다.