• Geomechanics and Engineering
• /
• v.6 no.5
• /
• pp.437-453
• /
• 2014

This paper studies the swelling and strength characteristics of unimproved and improved expansive soils in terms of the swell potential, swelling pressure, rate of secondary swelling, unconfined compressive strength and California bearing ratio (CBR). The admixtures used in this study are locally available cement and fly ash. The soils used in this study were taken from the Mae Moh power plant, Lampang Province, in northern Thailand. A conventional consolidation test apparatus was used to determine the swelling of the soil specimen. The optimum admixture contents are determined to efficiently reduce the swelling of unimproved soil. The rate of secondary swelling for unimproved soil is within the range of highly plastic montmorillonite clay, whereas the specimens improved with optimum admixture contents can be classified as non-swelling kaolinite. A soil type affects the swelling pressure. Expansive soil improvement with fly ash alone can reduce swelling percentage but cannot enhance the unconfined compressive strength and CBR. The strength and swelling characteristics can be predicted well by the swelling percentage in this study.

• Nuclear Engineering and Technology
• /
• v.56 no.2
• /
• pp.552-557
• /
• 2024

The actual swelling of AgInCd absorber might exceed the predicted swelling value after years of service in pressurized water reactors, and the chemical and microstructural changes of AgInCd absorber induced by transmutation reactions are the main reason for the swelling acceleration of AgInCd absorber. In the present study, a model for calculating the irradiation swelling of AgInCd absorber in nuclear control rods is developed according to chemical and microstructural changes of AgInCd absorber. In this model, the chemical compositions of AgInCd absorber as a function of the thermal neutron fluence are firstly calculated, and then the volume of AgInCd absorber after irradiation is obtained on the basis of the crystallographic parameters of phases in the AgInCd absorber, and the irradiation swelling of AgInCd absorber is finally calculated. The crystallographic parameters can be obtained by preparing the simulated AgInCd alloys and fitting the experimental data. The model calculating results of irradiation swelling are in good agreement with the actual swelling data in literature. More importantly, the present model can well explain the EPRI results of the acceleration in the diametral swelling rate above 6-8 × 10²⁰ n/cm² and the decrease in the diametral swelling rate above about 2 × 10²¹ n/cm².

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.2
• /
• pp.16-22
• /
• 2007

The behavior of ramie fibers and some wood elements in the early stage of alkali swelling was examined. When the fibers were treated with alkali solution, they significantly shrank in length and swelled in wall thickness. Ramie fibers showed a shrinkage averaging 23% in length and a swelling averaging 92% in width in 100 seconds treating time. Dimensional changes showed different fashion in each element of woods. The tracheids of latewood especially in Pinus densiflora and Larix kaempferi woods swelled intensively and showed balloon swelling, but in the case of Cryptomeria japonica, it was hardly observed. The swelling morphology of libriform fibers was similar to that of tracheids. The walls of vessel elements and parenchyma cells also swelled considerably in thickness but, no balloon swelling was found in both elements. The differences of swelling in different elements can be interpreted in terms of the differences of organization and/or chemical components of the cell walls.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3723-3740
• /
• 2021

The harsh conditions in the reactor affect the thermal and mechanical performance of the fuel plate heavily. Some in-pile behaviors, like fission-induced swelling, can cause a large deformation of fuel plate at very high burnup, which may even disturb the flow of coolant. In this research, the emphasis is put on the thermal expansion, fission-induced swelling, interaction layer (IL) growth, creep of the fuel meat, and plasticity of the cladding for the U₃Si₂/Al dispersion fuel plate. A detailed model of the fuel meat swelling is developed. Taking these in-pile behaviors into consideration, the three-dimensional large deformation incremental constitutive relations and stress update algorithms have been developed to study its thermal-mechanical performance under normal conditions using Abaqus. Results have shown that IL can effectively decrease the thermal conductivity of fuel meat. The high Mises stress region mainly locates at the interface between fuel meat and cladding, especially around the side edge of the interface. With irradiation time increasing, the stress in the fuel plate gets larger resulting from the growth of fuel meat swelling but then decreases under the effect of creep deformation. For the cladding, plasticity deformation does not occur within the irradiation time.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.7
• /
• pp.981-985
• /
• 2006

Novel copolymers consisting of poly(2-hydroxyethyl aspartamide-co-N,N'-dimethyl-1,3-propane aspartamide) (PHEA-DPA) were prepared from polysuccinimide (PSI), which is the thermal polycondensation product of aspartic acid, via a ring-opening reaction with N,N'-dimethyl-1,3-propane diamine (DPA) and ethanolamine. The prepared water-soluble copolymer was then crosslinked by reacting it with hexamethylene diisocyanate to provide the corresponding gel. The swelling behavior and morphology of the crosslinked hydrogels were investigated. The degree of swelling decreased with increasing crosslinking reagent due to the higher crosslinking density. It was also confirmed that the swelling property is affected by pH. At low pH (< pH 4), swelling is increased due to the ionization of DPA with a tertiary amine moiety. In addition, a reversible swelling and de-swelling behavior was demonstrated by adjusting the pH of the solution. The prepared hydrogels showed a well-interconnected microporous structure with regular 5-20 $\mu$m sized pores.

• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.342-349
• /
• 2016

Characteristics of the swelling-induced wrinkles on the surfaces of natural rubber (NR) film were investigated. The wrinkle structure was generated by swelling of NR film pre-stretched and firmly bonded onto an aluminum substrate in hexane. A novel experimental method was adopted to replicate the swelling-induced wrinkles on the NR film using an epoxy-hardener system. To get insight into the wrinkle parameters; the wrinkle length (L), wrinkle distance (D), wrinkle height (H) and the angle between two consecutive wrinkles (${\theta}$), the cross-sections of the replicas obtained from saturated swollen NR film were examined using an optical microscopy (OM). From the OM images, the wrinkling parameters were measured as a function of the thickness of NR film from 0.42 to 1.76 mm. Also, it was evaluated that the effects of swelling time on the wrinkling parameters. The length (L), distance (D) and height (H) of wrinkles increased as the thickness of the NR film and the swelling time increased. However, the angle between the wrinkles (${\theta}$) showed a sharp decrease up to a swelling time of 200 minutes and slightly decreased afterwards.

• Advances in materials Research
• /
• v.1 no.4
• /
• pp.269-284
• /
• 2012

Thermoresponsive hydrogels based on N-Isopropylacrylamide (NIPAM) and 2-Hydroxyethylacrylate (HEA) were prepared by free radical polymerization. The hydrogels were characterized by elemental (CHN) analysis, differential scanning calorimetry (DSC) and thermo gravimetric analysis (TGA). DSC thermogram showed two endothermic transitions which are due to hydration of water present in different environments. One near $0^{\circ}C$ called melting transition of ice and was used to calculate the quantitative determination of the amounts of freezing and non freezing water. The other transition above the ambient temperature was due to the combination of hydrophobic hydration and hydrophilic hydration which changes with the copolymer compositions. Swelling and deswelling studies of the hydrogels were carried out using the aqueous media, salt and urea solutions. The experimental results from swelling studies revealed that copolymers have lower rates of swelling and deswelling than the homopolymer.

• Geomechanics and Engineering
• /
• v.17 no.1
• /
• pp.69-79
• /
• 2019

This work presents an experimental study of the hydromechanical behavior of a natural swelling soil taken from Boumagueur region east of Algeria. Several pathological cases due to the soil shrinkage / swelling phenomenon were detected in this area. In a first part, the hydric behavior on drying-wetting paths was made, using the osmotic technics and saturated salts solutions to control suction. In The second part, using a new osmotic oedometer, the coupled behavior as a function of applied stresses and suction was investigated. It was shown that soil compressibility parameters was influenced by suction variations that an increase in suction is followed by a decrease in the virgin compression slope. On the other hand, the unloading slope of the oedometric curves was not obviously affected by the imposed suction. The decrease in suction strongly influences the apparent preconsolidation pressure, ie during swelling of the samples after wetting.

• Nuclear Engineering and Technology
• /
• v.31 no.2
• /
• pp.139-150
• /
• 1999

The swelling pressure of a potential buffer material was measured and the effect of dry density, bentonite content and initial water content on the swelling pressure was investigated to provide the information for the selection of buffer material in a high-level waste repository. Swelling tests were carried out according to Box-Behnken's experimental design. Measured swelling pressures were in the wide range of 0.7 Kg/$\textrm{cm}^2$ to 190.2 Kg/$\textrm{cm}^2$ under given experimental conditions. Based upon the experimental data, a 3-factor polynomial swelling model was suggested to analyze the effect of dry density, bentonite content and initial water content on the swelling pressure The swelling pressure increased with an increase in the dry density and bentonite content, while it decreased with increasing the initial water content and, beyond about 12 wt.% of the initial water content, levelled off to nearly constant value.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2616-2628
• /
• 2021

The results of effective irradiation swelling in a wide range of burnup levels are numerically obtained for an inert matrix fuel, which are verified with DART model. The fission gas swelling of fuel particles is calculated with a mechanistic model, which depends on the external hydrostatic pressure. Additionally, irradiation and thermal creep effects are included in the inert matrix. The effects of matrix creep strains, external hydrostatic pressure and temperature on the effective irradiation swelling are investigated. The research results indicate that (1) the above effects are coupled with each other; (2) the matrix creep effects at high temperatures should be involved; and (3) ranged from 0 to 300 MPa, a remarkable dependence of external hydrostatic pressure can be found. Furthermore, an explicit multi-variable mathematic model is established for the effective irradiation swelling, as a function of particle volume fraction, temperature, external hydrostatic pressure and fuel particle fission density, which can well reproduce the finite element results. The mathematic model for the current volume fraction of fuel particles can help establish other effective performance models.