• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.89-98
• /
• 2003

반도체 소자의 배선용 재료로서 사용가능한 합금원소 Mg를 첨가한 Cu(Mg) 박막의 기계 및 전기적 특성 변화를 조사하였다. Cu(2.7at.%Mg) 박막은 열처리를 할 경우 Cu 박막에 비하여 표면거칠기는 약 1/10 정도로 줄고 $SiO_2$와의 접착력도 2배 이상 향상된 결과를 나타내었다. 또한 $300^{\circ}C$이상의 온도에서 10분 이상 열처리를 할 경우 급격한 저항감소를 보여주었는데 이는 Mg 원소의 확산으로 인해 표면 및 계면에서 Mg 산화물이 형성되고 내부에는 순수 Cu와 같이 되었기 때문이다. 경도 및 열응력에 대한 저항력도 Cu박막에 비해 우수한 것으로 나타났으며 열응력으로 인해 Cu 박막에 나타나던 표면 void가 Cu(Mg) 박막에서는 전혀 관찰되지 않았다. EM Test 결과 lifetime은 2.5MA/$cm^2$, $297^[\circ}C$에서 순수 Cu 라인보다 5배 이상 길고 BTS Test 결과 Capacitance-Voltage 그래프의 플랫 밴드 전압(V$_{F}$ )의 shift현상이 Cu에서는 나타났지만 Cu(Mg) 박막에서는 발생하지 않는 우수한 신뢰성을 보여주었다. 누설전류 측정을 통한 $SiO_2$의 파괴시간은 Cu에 비하여 약 3배 이상 길어 합금원소에 의한 확산방지 효과가 있음을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.281-284
• /
• 2007

Recently, we have developed p-i-n a-Si:H single junction thin film solar cells with RF (13.56MHz) plasma enhanced chemical vapor deposition (PECVD) system, and also successfully fabricated the mini modules ($>300cm^2$), using the laser patterning technique to form an integrated series connection. The efficiency of a mini module was 7.4% ($Area=305cm^2$, Isc=0.25A, Voc=14.74V, FF=62%). To fabricate large area modules, it is important to optimise the integrated series connection, without damaging the cell. We have newly installed the laser patterning equipment that consists of two different lasers, $SHG-YVO_4$ (${\lambda}=0.532{\mu}m$) and YAG (${\lambda}=1.064{\mu}m$). The mini-modules are formed through several scribed lines such as pattern-l (front TCO), pattern-2 (PV layers) and pattern-3 (BR/back contact). However, in the case of pattern-3, a high-energy part of laser shot damaged the textured surface of the front TCO, so that the resistance between the each cells decreases due to an incomplete isolation. In this study, the re-deposition of SnOx from the front TCO, Zn (BR layer) and Al (back contact) on the sidewalls of pattern-3 scribed lines was observed. Moreover, re-crystallization of a-Si:H layers due to thermal damage by laser patterning was evaluated. These cause an increase of a leakage current, result in a low efficiency of module. To optimize a-Si:H single junction thin film modules, a laser beam profile was changed, and its effect on isolation of scribed lines is discussed in this paper.

• 마이크로전자및패키징학회지
• /
• 제12권4호통권37호
• /
• pp.359-363
• /
• 2005

유기 박막트랜지스터 (OTFT)를 제작하기 위하여 게이트 절연막으로서 PVP 계통의 유기막을 갖는 MIM(metal-insulator-metal)구조의 유기 절연층 소자를 제작하였다. 유기 절연층의 형은 ITO/Glass 기판위에 polyvinyl 계열의 PVP(poly-4-vinylphenol)를 용질로, PGMEA (propylene glycol monomethyl ether acetate)를 용매로 사용하여 co-polymer PVP를 제조하였다. 또한 열경화성 수지인 poly(melamine-co-formaldehyde)를 경화제로 사용하여 cross-linked PVP 절연막을 합성하였다. 유기 절연층의 전기적 특성은 co-polymer PVP 소자에 비해 cross-link 방식으로 제조된 소자에서 약 300 pA의 낮은 누설전류와 상대적으로 낮은 잡음전류의 특성을 나타내었다. 또한 cross-linked PVP 절연막에서 보다 양호한 표면형상 (거칠기)이 관찰되었으며 정전용량 값은 약 0.11${\~}$0.18 nF의 값을 나타내었다.

• 한국전자파학회논문지
• /
• 제11권3호
• /
• pp.388-402
• /
• 2000

주기적인 구형격자를 갖는 유전체 코팅된 도체 실린더에 대해 무한 주기 구조와 유한 주기 구조에 대한 누설 파 안테나의 복사 특성을 이론적으로 해석하였다. 무한 주기 구조에 대하여는 모드 정합 법을 적용하여 해석하 였고, 유한 주기 구조에 대하여는 퓨리에 변환과 모드 전개를 사용하여 적분 방정식을 유도하고 선형 연립 방정 식을 얻는다. 구형격자의 폭, 깊이, 유전체 코팅두께, 도체 실린더의 반경, 유한 구형격자 개수의 영향이 위상 상 수, 누설 상수 및 복사패턴 등과 복사 특성에 미치는 영향을 조사하였고, 유한 주기 구조와 무한 주기 구조의 결 과를 비교하고 잘 일치함을 확인할 수 있었다. 균일 유한 주기 구형격자에 의한 높은 측엽을 줄이기 위해 안테나 의 전후단 부에 테이퍼링과 비균일 준주기 슬롯배열을 고려하였다. 또한 구형격자 표면파 안테나에 사용되는 구 형격자 주기. 폭, 깊이에 대해 테이퍼링을 통해 낮은 측엽을 갖는 endfire 복사패턴을 얻을 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.462-462
• /
• 2014

The effect of rear passivation for passivated emitter and rear cell (PERC) using ozone and H2O oxidant of atomic layer deposited (ALD) Al2O3 was studied by post-annealing in N2 and forming gas ambients. Rear surface of PERC solar cell was passivated by Al2O3 grown by ALD with ozone and H2O oxidant. Al2O3 grown by ALD with ozone oxidant has been known to have many advantages, such as lower interface defects, low leakage current density. Its passivation quality is better than Al2O3 with H2O. Al2O3 layer with 10 nm and 20 nm thickness was grown at $150^{\circ}C$ with ozone oxidant and at $250^{\circ}C$ with H2O oxidant. And then each samples were post-annealled at $450^{\circ}C$ in N2 ambients and at $850^{\circ}C$ in forming gas ambients. The passivation quality was investigated by measuring the minority carrier lifetime respectively. We examined atomic layer deposited Al2O3 such as growth rate, film density, thickness, negative fixed charge density at AlOx/Si interface, and reflectance. The influences of process temperature and heat treatment were investigated using Sinton (WCT-120) by Quasi-Steady State Photoconductance (QSSPC) mode. Ozone-based ALD Al2O3 film shows the best carrier lifetime at lower deposition temperature than H2O-based ALD.

• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.152-163
• /
• 1995

This experiment was performed to observe the adhesion pattern and microleakage in the gingival margin according to variation in the resin cement thickness which results from thickness of Die spacer. which is considered to effect the adaptability of the composite resin inlays. Clearfil CR inlays were fabricated on stone models with CR Sep applicated once and Nice fit twice, 4 times, and 6 times each. After 2nd curing within the CRC-100 oven, CR inlays were cemented with CR inlay cement. Dye(2% methylene blue) penetration and adhesion pattern were evaluated after sectioning of gingival margin into :3 pieces. The results were as follows ; 1. The thickness of resin cement showed unevenchanging pattern with that of die spacer, namely, it was increased until 4 times' application of Nice-Fit but was decreased with 6 times' application of that. 2. The degree of dye penetration wasn't affected by cement thickness within a limited value. 3. Most of dye penetration was shown through the interface between cement and enamel rather than the interface between cement and CR inlay. This shows that the affinity of resin cement for CR inlay was superior to the adhesive strength with tooth structure. 4. No gap was found at the interface between enamel and cement but some showed separation between dentin and cement. It is concidered that the contraction force of cement was less than the bond strength with the enamel. 5. Lots of voids were found in the CR inlay and resin cement. There was a pooling tendency of bonding agent and cement in the axiogingival line angle portion. 6. In some specimens, cracks were shown in enamel margin. From this it could be considered that cavity preparation and surface treatment weakened the tooth structure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.54-57
• /
• 2003

[ $HfO_xN_y$ ] films using a hafnium tertiary-butoxide $(Hf[OC(CH_3)_3]_4)$ in plasma and $N_2$ ambient were prepared to improve the thermal stability of hafnium-based gate dielectrics. A 10% nitrogen incorporation into $HfO_2$ films showed a smooth surface morphology and a crystallization temperature as high as $200^{\circ}C$ compared with pure $HfO_2$ films. The $TaN/HfO_xN_y/Si$ capacitors showed a stable capacitance-voltage characteristics even at post-metal annealing temperature of $1000^{\circ}C$ in $N_2$ ambient and a constant value of 1.6 nm EOT (equivalent oxide thickness) irrespective of an increase of PDA and PMA temperature. Leakage current densities of $HfO_xN_y$ capacitors annealed at PDA temperature of 800 and $900^{\circ}C$, respectively were approximately one order of magnitude lower than that of $HfO_2$ capacitors.

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.439-448
• /
• 2009

Three inducers were designed to avoid cavitation instabilities. This was accomplished by avoiding the interaction of tip cavity with the leading edge of the next blade. The first one was designed with extremely larger leading edge sweep, the second and third ones were designed with smaller incidence angle by reducing the inlet blade angle or increasing the design flow rate, respectively. The inducer with larger design flow rate has larger outlet blade angle to obtain sufficient pressure rise. The inducer with larger sweep could suppress the cavitation instabilities in higher flow rates more than 95% of design flow coefficient, owing to weaker tip leakage vortex cavity with stronger disturbance by backflow vortices. The inducer with larger outlet blade angle could avoid the cavitation instabilities at higher flow rates, owing to the extension of the tip cavity along the suction surface of the blade. The inducer with smaller inlet blade angle could avoid the cavitation instabilities at higher flow rates, owing to the occurrence of the cavity first in the blade passage and its extension upstream. The cavity shape and suction performance were reasonably simulated by three dimensional CFD computations under the steady cavitating condition, except for the backflow vortex cavity. The difference in the growth of cavity for each inducer is explained from the difference of the pressure distribution on the suction side of the blades.

• 한국진공학회지
• /
• 제9권4호
• /
• pp.341-345
• /
• 2000

p형 Si (100)기판 위에 reactive DC magnetron sputtering으로 증착한 $ZrO_2$박막에 대하여 증착 조건과 열처리 조건에 따른 미세구조의 변화 및 전기적 특성 변화를 관찰하였다. 증착 및 열처리 온도가 증가하고 power 증가할수록 $ZrO_2$의 굴절율은 증가되어 이상적인 2.0~2.2에 근접하였다. 상온에서 증착된 $ZrO_2$ 박막은 비정질이며 $300^{\circ}C$에서 증착한 경우 $ZrO_2$박막은 다결정이었다. 산소 분위기에서 열처리를 수행한 박막의 RMS 값은 증착직후보다 높아지고 계면 산화막은 산소의 확산에 의해 두께가 증가하였다. A1/$ZrO_2$/p-type Si(100)의 C-V과 I-V 특성을 관찰하였고, 그 결과 산소분위기에서 열처리하는 경우 계면 산화막의 두께증가로 Cmax 및 누설전류가 감소함을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.312-317
• /
• 2000

Ferroelectric S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ solutions were synthesized using sol-gel process in which strontinum ethoxide bismuth ethoxide trantalum ethoxide were used a s startring materials. SBT thin films were coated on Pt/Ti/ $SiO_2$/Si substrates by spin-coating. rapid thermal annealing (RTA) was used to promote crystallization. Thin films were annealed at $700^{\circ}C$ for 1 hr in an oxygen atmosphere. This temperature is about 10$0^{\circ}C$ lower than the usual annealing temperature for SBT thin films. Pt top-electrode was deposited by sputtering and thin films were post-annealed at $700^{\circ}C$ for 30 min. to enhance electrical properties. As the RTA temperature increased the higher 2 $P_{r}$ values were obtained. At RTA temperature being 78$0^{\circ}C$ remanent polarization of S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ thin film was 7.73 $\mu$C/cm $_2$ and the leakage current density was 1.14$\times$10$^{-7}$ A/c $m^2$ at 3 V. As RTA temperature increased the breakdown voltage was decreased. It is considered that the low-field breadown is caused by the rough surface of SBT films and forming bismuth metal in SBT thin films.films.lms.