• 한국도로학회논문집
• /
• 제6권4호
• /
• pp.109-121
• /
• 2004

본 연구는 한국형 포장설계법 과제의 일환으로 수행된 콘크리트슬래브의 건조수축특성에 대한 연구로서 형상비 및 굵은 골재의 종류를 달리해 현재까지 252일간 수행된 실험결과이다. 실제 포장용 콘크리트 슬래브의 형상비에 접근하기 위한 방안으로 시편 일부 면의 수분 증발을 막기 위해 일부 면에 3중 코팅 처리와 랩 처리를 하였다. 예비실험결과 본 실험에서 채택한 수분방지 코팅 처리가 3달 정도까지는 신뢰성이 있음을 알 수 있었다. 동일한 형상비에서 사암을 사용한 콘크리트 시편의 건조수축이 석회암인 경우보다 형상비에 따라 1.32$\sim$1.80배 크게 측정되었다. 측정된 건조수축 변형률을 기존의 ACI와 CEB-FIP의 건조수축 모델식과 비교한 결과 두 식 모두 과소평가됨이 확인되었다. 최종적으로 재령 및 형상비 등을 고려한 다중 비선형 회귀분석을 통해 본 실험에 적합한 콘크리트시편의 건조수축 모델식을 제시하였다.

• 한국식품과학회지
• /
• 제32권1호
• /
• pp.132-139
• /
• 2000

본 연구는 분무건조를 이용한 미세캡슐화 기술을 이용하여 유화압력 및 분무건조에 있어서 송풍 온도와 분무 속도를 최적화하는데 목표를 갖고 수행되었다. 분석지표로 유화액의 유화안정성과 flavor release를, 분무건조 분말의 total oil, surface oil, flavor release, 흡습성을 측정하고, SEM에 의해 분말의 형태를 관찰하였다. Wall system을 이용하여 piston-type homogenizer의 압력을 달리하여 실험한 결과 향기성분의 미세캡슐화를 위한 최적 유화압력은 20.7MPa이었다. 분무건조공정에 있어서 송풍 온도와 분무 속도를 독립변수로, total oil retention, surface oil content, flavor release를 종속변수로 반응 표면 분석법을 행한 결과 송풍 온도는 $170{\circ}C$, 분무 속도는 15,000rpm이 우수한 공정 조건임을 예측 할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.125-131
• /
• 2011

The characteristics of radio-frequency/vacuum drying Japanese larch boxed heart round logs with 150 mm and 210 mm in diameter and 2,500 mm in length, subjected to compressive loading, after the pretreatment of kerf were investigated. The results of this study were as the follows: The drying time of about 120 hours~130 hours was needed from green to about 15 percent of moisture content. The gradient of final moisture content for all specimens was very gentle in both longitudinal and transverse directions owing to dielectric heating. The surface checks seriously occurred although the occurrence extent of surface check for the kerfed specimens was slight compared with that for the control specimens because drying stress was relieved by kerf. The occurrence of surface checks for the L-specimen was more serious than that for the S-specimen.

• 한국건축시공학회지
• /
• 제16권3호
• /
• pp.211-217
• /
• 2016

본 연구에서는 2015년 가을철 실제 시공중인 고층 아파트를 대상으로 1중 백색 버블시트로 타설된 콘크리트의 표면을 덮어주는 버블시트 피복양생 공법과 표면을 노출한 채로 양생없이 유지하는 표면노출 방법간을 비교하여 소성 및 건조수축균열의 저감정도를 분석하였다. 실험 결과, 버블시트를 시공하였을 경우, 수화열 및 적산온도는 표면노출보다 약간 높았고, 바닥 균열의 갯수, 길이, 최대 균열폭, 균열 면적 모두 현저하게 적은 값이 측정되었다. 따라서 가을철 버블시트를 타설된 콘크리트 표면에 적용 할 경우에는 소성 및 건조수축균열을 획기적으로 방지할 수 있는 효과적인 표면피복 양생공법인 것으로 판단되었다.

• 센서학회지
• /
• 제15권3호
• /
• pp.173-178
• /
• 2006

Silica aerogel with ultra low density and high porosity has been focused on versatile application due to its fascinating properties. Ambient drying process of waterglass, in this study was researched to fabricate a crack-free monolith body in the point view of cost effective way. Wet gel was obtained by removing of $Na^{+}$ ions in waterglass, which contains 8 wt% of $SiO_{2}$. Xylene, which has a low vapor pressure, was used as a solution substitutor to prevent the formation a cracks during drying. Various surface modifiers like as hexamethyldisilazane (HMDSZ), trimethylchlorosilane (TMCS), methyltriethoxylsilane (MTES), methyltrimethoxysilane (MTMS) and phenyltriethoxysilane (PTES) were used in order to improve hydrophobicity of the waterglass Silica aerogel. Some physical properties of the surface modified aerogels were investigated by FT-IR, TGA, BET and SEM. Hydrophobicity and hydrophilicity of Silica aerogel is attributed to the Si-OH bond and the non-polar C-H bond groups on the surface of aerogel. Crack-free waterglass aerogel with >90 % of porosity, 17 nm of pore size and <0.15 $g/cm^{3}$ of density was prepared. HMDSZ and TMCS are effective as a surface modifier

• 센서학회지
• /
• 제15권5호
• /
• pp.371-377
• /
• 2006

Nano porous, transparent silica aerogels monoliths were prepared under ambient drying (1 atm, $270^{\circ}C$) condition by the combination of sol-gel process and surface modification with subsequent heat treatment. Three kinds of solvent, n-hexane, n-heptane and xylene, were selected in the point view of low surface tension and vapor pressure in order to restrain a formation of cracks during drying. Crack-free silica aerogels with over 93 % of porosity and below $0.14g/cm^3$ of density were obtained by solvent exchange and surface modification under atmosphere condition. Optimum solvent was confirmed n-heptane among these solvents through estimation of FT-IR, TGA, BET and SEM. Modified silica aerogel exhibited a higher porosity and pore size compare to unmodified aerogels. Hydrophobicity was also controled by C-H and H-OH bonding state in the gel structure and heat treatment over $400^{\circ}C$ effects to the hydrophobicity due to oxidation of C-H radicals.

• 한국농공학회지
• /
• 제38권5호
• /
• pp.116-124
• /
• 1996

The purpose of The work described in this paper is to clear up the initial moisture content, specific surface, air drying and freezing-thawing process on liquid limit of clayey soils distributed widely at estuary of three main rivers in the west coast. To this end, a series of tests were conducted on clayey soils samples with natural state and treated state. From the test results, the liquid limit was decreased with decrement of initial moisture content, air drying process, and freezing-thawing cycles and increased with increment of specific surface. The specific surface which influenced on the liquid limit is over $25 m^2$m$^2$/g, and their relationships are well formulated. Air drying process is expected to improve the engineering properties of the soils such the pro-water properties were changed to anti-water proper-ties through lowering of water holding as resulted to incline from A-7-5 to A-5 on the soil classificaction plastic chart. The freezing-thawing process decreased 20% of liquid limit, especially under the first cycle of the behavious, as a result of above mentioned reasons, phase change of soil-water system brought the decrement of specific surface and affected to the liquid limit.

• Advances in concrete construction
• /
• 제3권1호
• /
• pp.39-54
• /
• 2015

Relative humidity and strains within a massive concrete cylinder (${\varphi}450mm{\times}900mm$) in the drying and the re-saturating process were measured for elucidating the process of ASR surface cracking in concrete. The expansion behavior of mortars in dry atmospheres with various R.H. values and the resaturating process was revealed. Non- or less-expansive layers were formed in near-surface regions in the concrete cylinder in the drying process, but ASR expansions actively progressed in inner portions. After resaturating, R.H. values of near-surface regions rapidly increased with time, but expansions in the regions were found to be very small. However, in the middle portions, of which R.H. values were kept 80% ~ 90% R.H. in the drying process, expansion actively progressed, resulting in further development of surface cracks in the re-saturating process.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.21-26
• /
• 2001

Acquisition of precise information on drying characteristics of wood is indispensable for the improvement of drying schedules and wood quality. Recognition of the exact moisture content at which drying defects such as checks occur during drying with given drying conditions may be essential to reduce drying losses. In this study an image-processing system was combined with a laboratory-scale wood dry kiln for experiments and the surface of tree disk of black locust (Robinia pseudoacacia L.) was monitored to investigate the behavior of check formation over all the drying process. This system showed good potential for improving drying schedules and wood product quality.

• 한국세라믹학회지
• /
• 제24권3호
• /
• pp.257-262
• /
• 1987

The characteristics of cobalt oxide powders prepared by hot petroleum drying method from the cobalt acetate were evaluated by DTA/TGA, XRD, BET, SEM and density measurement. The cobalt oxide powder could be prepared by hot petroleum drying of the emulsion of cobalt acetate salt solution and the subsequent thermal decomposition of the acetate at 300$^{\circ}C$. As the concentration of the salt solution and the calcination temperature of the dried powder increased, the surface area of the synthesized powder decreased due to the particle growth, so that after sintering the density and grain size decreased. For the same concentration of the salt solution, the surface area and sinterability of the powder by hot petroleum drying increased in comparision with those by conventional drying.