• Journal of Mechanical Science and Technology
• /
• v.20 no.11
• /
• pp.1942-1949
• /
• 2006

Typically, condensate forms as droplets on the fin surfaces and may bridge the space between the fin surfaces. This is due to the dry characteristics inherent to the fin surface. The droplets increase the air-side pressure drop. In the case of high air velocities, these droplets may be blown off the fins and entrained in the air stream. To minimize the formation of condensate droplet, the wet ability of the fins must be improved. The carry-over velocity is affected by fin surface characteristics. To avoid carry-over in the air conditioner having the highest air velocity of 1.5 m/sec, the dynamic contact angle (DCA) should be at least lowly under $60^{\circ}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.178-184
• /
• 1996

Electrical properties such as surface flashover discharge and discharge degradations of insulating materials for superconducting cable have been investigated. It is found that the surface voltage is proportional to /$\^$0.7/(/: discharge length) in LHe(Liquid Helium). V-t characteristic LHe were a n=5.5 that was less than liquid N$_2$. After applied AC voltage, the surface condition of polymer films were observed non-eroded area and eroded area. The eroded area is depending on the applied voltage. In case of LHe, the crack was observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.194-199
• /
• 1996

Grinding burn formed on the ground surface is related to the maximum temperature of workpiece surface and wheel temperature in the grinding process. The thermal characteristics of workpiece and grinding conditions on the surface temperature of the oxidation growing layer after get out of contact with the grinding wheel. The assumption used in grinding power signatures leads to the local temperature distribution between grinding wheel and workpiece, i.e., a single curve determines temperatures anywhere within the grinding wheel at anytime. This information is useful in the study of the grinding bum penetration into the wheel and thus provides an presentation of grinding trouble monitoring for the burning. On the basis of grinding power signatures in the wheel, thermally optimum conditions are defined and controlled. To cope with grinding burn, the use of grinding power signatures is an effective monitoring systems when occurring the grinding process. In this paper, the identified parameters suggested in this study which are derived from the grinding power signatures are presented.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.242-248
• /
• 2000

This paper has focused on the optimization of the cutting parameters for turning operation based on the Taguchi method. Four cutting parameters, namely, cutting speed, feed, depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using the signal-to-noise (S/N) ratio, analysis of variance (ANOVA). The experiments have been peformed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.184-186
• /
• 2002

The evolution of texture and microstructure during warm rolling and subsequent annealing in aluminium 3004 alloy sheet was investigated by X-ray texture measurements and microstructure observations. Warm rolling at 250$^{\circ}C$ led to the development of strong through thickness texture gradients with shear textures at the surface layer and a regular rolling texture in the center of the sheets. FEM simulations indicated that these texture gradients are caused by pronounced strain gradients throughout the sheet thickness. Upon recrystallization annealing, in the sheet center the characteristic cube-recrystallization texture developed, while in the surface layers with a pronounced shear texture continuous recrystallization took place which led to the formation of a very fine grained microstructure. It is concluded that the very complex strain history in the near-surface layers together with the resulting high work-hardening rate gave rise to the formation of the ultra-fine grains with an average size smaller than 2$\mu\textrm{m}$.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.326-330
• /
• 2010

The surface oxidation of magnesium was performed by burning and PEO treatment method. The scanning electron microscopy (SEM), EDS, and I-V characteristics have been applied to the study of the oxidation status. The sample formed by buring method shows weaker corrosion-resistant property than that by PEO method, but this shows more conducting property.

• Laser Solutions
• /
• v.18 no.4
• /
• pp.6-11
• /
• 2015

Specially designed and 3D printed samples were prepared and joined by a diode laser source. To increase the strength of joining and reliability of samples, the surface was patterned by using a 3D printer. The joining surface was prepared as hemispherical shape with no-patterns, 0.5mm pitch, 0.75mm pitch and 1mm pitch. The optical properties of samples were measured by using an integrated sphere where classical Kubelka-Munk theory and modified Richard-Mudgetts theory for the analysis applied. Scanning speed was set at 500mm/min and laser power was varied between 9 and 10watts for the preliminary joining characteristic analysis.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.6
• /
• pp.1-7
• /
• 1993

After the 1%S-Al metal is deposited, a thin oxide is formed thereon. Then, a single charged Argon(Ar$^{+}$) is ion implanted into the oxide layer, thereby causing the metal grain in the upper surface of the metal layer to become amorphous. Consequently, the grain size will be reduced and the rough surface of the metal layer flattened. However, the remainder of the metal layer beneath the upper surface thereof will still exhibit large grain size and low resistance, because the Argon ion is only implanted to characterized by a dual-sized grain structure which served to reduce interlayer stress, thereby decreasing the rate of stress migration, and to lower the resistivity of the metal line, thereby enhancing the electromigration characteristic thereof. Experiments have shown that the metal line exhibits a metal migration rate which is approximately 700% less than the control group and a standard deviation which is approximately 200% less than these group.p.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.52-56
• /
• 2004

The movement of electron in the semiconductor-gap-semiconductor was observed by the variation of V-I characteristic as a distance two ZnO(1010) single crystals. When the resistance between two crystals was $10^2{\sim}10^4{\Omega}$, V-I characteristics had the pattern of the field emission or ohmic contact. On the other hand, when the resistance was larger than $10^7{\Omega}$ by increasing the distance between two crystals, the effect of surface barrier was prominent. This result leads to the conclusion that both the field emission (or ohmic contact) and the surface barrier effect including the tunneling have the influence on V-I characteristics of mechanically contacted crystals.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.2
• /
• pp.133-141
• /
• 2000

Enhanced the value of badge good with the gold plating of emblem, sports pictogram, mascot in 2002 Asian Game and World Cup, applying the plating and coating technique to screen printing. In addition, tourist and characteristic goods were of great value and image of visual communication displayed outside. After the screen printing in the surface of stainless steel, it obtained the plate coloring of beautiful a black glossy with a black Ru plating. At the identical surface, it did that the electrodeposition coating process in order to making a conductor state of image areas and a nonconductor state of nonimage areas. After the electrodeposition process, it removed the printing ink of image areas with solvent. A manufacturing process, it removed the printing ink of image areas with solvent. A manufacturing process completed with copper, nickel and gold plating at bared metal surface.