• 한국표면공학회지
• /
• 제48권4호
• /
• pp.131-135
• /
• 2015

We investigated the surface morphology and the change of Ag concentration for SnAg electrodeposits according to the current density using labmade and commercial plating solutions. The concentration of Ag in the SnAg electrodeposits decreased with increasing the current density. The Ag concentrations at the conditions of over $50mA/cm^2$ were below 3 wt% and the surface was relatively smooth. Cu pillar bump was fabricated by using SnAg electroplating, and it was reflowed at $240^{\circ}C$ for 90 sec. The cross-sectional microstructure was investigated by using EBSD measurement and it was found that the grain size of SnAg became smaller by increasing the number of reflow treatments.

• 한국표면공학회지
• /
• 제30권6호
• /
• pp.365-373
• /
• 1997

316L and 420 Stainless steels were deposited onto AZ9ID commercial magnesium alloy by plasma spray process with various gas flow rate of, TEX>$H_2$ secondary gas. And hardness as well as were track volume, coefficient of friction also had been measured. wear and hardness were measured by using reciprocal configuration tribometer and microghardness tester, respectively. Also, the microstructure of the coatings surface the cross sectional area of coating surface and cross sectional area of coaing/Substrate interface had been analyzed with Scanning Electron Microscope(SEM) and Optical microscope(OM). Finally, optimal process parameters for the improvement of coating efficiency such as mechanical property and wear behavior were examined.

• Applied Microscopy
• /
• 제45권4호
• /
• pp.189-194
• /
• 2015

Backside Ar ion milling technique for the preparation of cross-sectional transmission electron microscopy (TEM) specimens, and backside-ion milling combined with focused ion beam (FIB) operation for electron holography were introduced in this paper. The backside Ar ion milling technique offers advantages in preparing cross-sectional specimens having thin, smooth and uniform surfaces with low surface damages. The back-side ion milling combined with the FIB technique could be used to observe the two-dimensional p-n junction profiles in semiconductors with the sample quality sufficient for an electron holography study. These techniques have useful applications for accurate TEM analysis of the microstructure of materials or electronic devices such as arrayed hole patterns, three-dimensional integrated circuits, and also relatively thick layers (> $1{\mu}m$).

• 한국표면공학회지
• /
• 제32권6호
• /
• pp.703-708
• /
• 1999

Silicides have been used extensively in ULSI logic device fabrication as contact materials for the active areas as well as the poly- Si gates. NiSi is a promising candidate for submicron device application due to less volume expansion, low formation temperature, little silicon consumption, and large stable processing temperature window. In this report, the microstructure of nickel silicides fabricated with a thermal evaporator has been investigated. We observed systematic transformation of Ni silicides of $Ni_2$Si, NiSi, $NiSi_2$, as annealing temperature increases. All the silicides have been identified by a X-ray diffractometer (XRD). The cross-sectional microstructure of silicides was examined by a transmission electron microscope (TEM) equipped with a energy dispersive spectrometer(EDS). The surface roughness of silicides was measured by scanning probe microscope(SPM). Although we observed thin oxide layer existed at the $Ni/NiSi_{x}$ interface, we fabricated successfully $550\AA$-thick planar Ni-monosilicide at the temperature range of$ 400~700^{\circ}C$.

• 대한기계학회논문집A
• /
• 제21권12호
• /
• pp.2019-2028
• /
• 1997

It has been well established that resistant force and wear that occur during rolling motion depend on several factors such as material type, hardness, subsurface microstructure, applied load, and speed. The purpose of this work is to investigate the effect of microstructure and the state of deformed layer on the rolling contact characteristics in dry and lubricated rolling contacts. The results of this work show that the rolling resistance behavior depends on the state of the deformed layer. Also, lubrication can reduce the plastic flow at the surface but may still have an effect on the subsurface strain. The cross-sectional view of the microstructure shows that surface traction has a difinite effect on the morphology of the surface region. That is, significant slip seems to have taken place between the ball than those of the dry rolling case. The surface generation effects were significantly less compared to the case of dry rolling contact.

• Archives of Metallurgy and Materials
• /
• 제67권4호
• /
• pp.1465-1468
• /
• 2022

In this study, we investigated the effect of cladding on structural carbon steel (S45C) using 5%Cr-1.5%Mo-Fe powder (SKD61), which is expected to show economically efficient production of die-casting parts. The process conditions were performed under argon atmosphere using a diode laser source with specialized wavelength of 900-1070 nm, and the output conditions were 3, 4, and 5 kW, respectively. After the cladding was completed, the surface coating layer's shape and the microstructure were analyzed. The hardness test was carried out with Micro Vickers hardness tester under 500 gram-force along the normal line at the interval of 0.2 mm from the surface to core direction on the cross-sectional area. In addition, polarization curve test of the surface coating layer was performed to investigate the corrosion resistance characteristics.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.285-293
• /
• 2016

The high velocity oxygen fuel(HVOF) thermal spray is a kind of surface modification techniques to produce the sprayed coating layer. This process is to form the coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. The efficiency of thermal spraying is dropped, however, because the semi-molten powder in a spray process become a factor that degrades the mechanical property by the formed pore within the coating layer. Therefore, it is necessary to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesive force. In this study, to improve the wear resistance, corrosion resistance and heat resistance, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps used in ironworks are manufactured with STS $420J_2$ and are coated by the powders of WC-Co-Cr and WC-Cr-Ni including the WC of high hardness using a HVOF thermal sprayer developed in this laboratory. These are called by the surface-modified plungers. The surface roughness, hardness, and surface and cross-sectional microstructure of these two surface-modified and conventional ceramic plungers are measured and compared before operation with after operation for 100 days. It is found that the values of centerline average surface roughness and maximum height for conventional ceramic plunger are 9.5 to 10.8 and 5.2 to 5.7 times higher than those of surface-modified ones coated by WC-Co-Cr and WC-Cr-Ni because the fine tops and bottoms on surface roughness curve of conventional ceramic plunger are approximately 100 times higher than those of surface-modified ones. In addition, the pores and scratches in the surface microstructure are considerably formed in the order of conventional ceramic, WC-Cr-Ni and WC-Co-Cr surface-modified plungers. The greater the WC content of high hardness powder is less the change in the plunger surface.

• 한국재료학회지
• /
• 제2권3호
• /
• pp.213-219
• /
• 1992

$As^{+}$이온을 주입시킨후 열처리 방법을 달리한 Si 표면부 미세구조와 성분분석 및 전기적특성을 조사하였다. 이온주입에 의해 형성되었던 비정질층은 열처리에 의해 결정화 되었으며 열처리방법에 따라 결정화 양상의 차이를 보였다. 또한 주입된 이온의 분포 및 전기저항을 미세구조와 비교한 결과 주입된 이온의 농도가 최대인 깊이에서 최대의 손상이 발견되었으며 열처리 후에도 매우 작은 결함이 존재하였다. 하지만 이러한 작은 결함들은 전기적 성질에 큰 영향을 미치지는 않은 것으로 나타났다.

• 한국분말재료학회지
• /
• 제25권1호
• /
• pp.36-42
• /
• 2018

In order to expand the application of oxide dispersion-strengthened (ODS) steel, a composite material is manufactured by adding mechanically alloyed ODS steel powder to conventional steel and investigated in terms of microstructure and wear properties. For comparison, a commercial automobile part material is also tested. Initial microstructural observations confirm that the composite material with added ODS steel contains i) a pearlitic Fe matrix area and ii) an area with Cr-based carbides and ODS steel particles in the form of a $Fe-Fe_3C$ structure. In the commercial material, various hard Co-, Fe-Mo-, and Cr-based particles are present in a pearlitic Fe matrix. Wear testing using the VSR engine simulation wear test confirms that the seatface widths of the composite material with added ODS steel and the commercial material are increased by 24% and 47%, respectively, with wear depths of 0.05 mm and 0.1 mm, respectively. The ODS steel-added composite material shows better wear resistance. Post-wear-testing surface and cross-sectional observations show that particles in the commercial material easily fall off, while the ODS steel-added material has an even, smooth wear surface.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.47-51
• /
• 2014

In this work, a possible mechanism for grain evolution in Al-Mg alloy films during thermal annealing is suggested on the basis of the phase transition and the related residual stress. Al-Mg alloy films with compositions of 14.0 and 18.0 wt% Mg content were deposited on cold-rolled steel substrates by the direct current co-sputtering method using Al and Mg targets. After the deposition, the samples were thermally annealed at $400^{\circ}C$ for 10 min. The featureless, dense cross-sectional microstructure of the as-deposited films turned into a grainy microstructure after the thermal annealing. According to the residual stress evaluated by using the $XRD-sin2{\psi}$ technique and the phase analysis by XRD, it is likely that grains were created in order to relieve the additional accumulation of residual stress originating from the phase transition from face-centered cubic Al (${\alpha}$) to Al3Mg2 (${\beta}$) and Mg (${\delta}$) phases, suggesting interplay between the microstructure and residual stress.