• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.374-381
• /
• 2001

Surface roughness plays a significant role in friction, wear, and lubrication in machine components. Most engineering surfaces have tile nogaussian height distrubution. So, in this study, elastic-plastic contact simulations are conducted for not only gaussian surfaces but also nongaussian surfaces. Nongaussian rough surface considering the kurtosis is generated numerically. The contact simulation model takes into account the plastic deformation behaviors of asperities by setting a celing on their contact pressure at material hardness value. It will be shown that the performace variables such as real contact area fraction, plastic area fraction and average gap are sensitive to the characteristics of surface geometry according to kurtosis.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.363-372
• /
• 1993

For more accurate height/depth control of the agricultural implements , the soil surface as a reference position should be measured as accurate as possible. A new measurement system using microwave was developed to detect the true soil surface even under plant and/or vegetation. Two-frequency continuous-wave radar was used as the measurement system. It could estimate the distance to the target by measuring the phase difference between two different frequencies continuous-waves which reflected on the target surface. The system performance was evaluated on the barely field where the average height of barley was 91.5 cm. The experimental results showed that the system performance was not affected by the existence of barely. The maximum measurement errors were 8.91 com and 8.44cm for two different experimental plots.

• The korean journal of orthodontics
• /
• v.17 no.2
• /
• pp.215-221
• /
• 1987

This study was designed to investigate the growth amount and rate of mandible by the measurements of mandibular lateral surface and the relationship of peak growth increments between mandible and body height The sample consisted of twenty-five boys and fifteen girls between the ages of 6 and 13 The surface of mandible was measured from digitized roentgenocephalometric analysis (A 27 point mandibular model) The findings of this study can be summarized as follows 1 No significant difference was found between mandibular lateral surfaces of the both sexes at the ages studied. 2 The mean growth amount of mandibular lateral surface from 6 to 13 years of ages was $9\;09cm^2$ in boys and $8\;29cm^2$ in girls, and the mean growth rate was 46 07% in boys and 42 57% in girls 3 The prepubertal peak growth increment in mandible was found between the ages of 11-12 in girls and 12-13 in boys 4 The prepubertal peak growth increments of mandible occured one year later that of body height in boys and girls.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.106-110
• /
• 2001

The ball-end milling process is widely used in the die/mold industries, and it is very suitable for the machining of free-form surfaces. However, this process is inherently inefficient process to compared with the end-milling or face milling process, since it relays upon the machining at the cutter/surface contact point. The machined part is the result of continuous point-to-point machining on the free-form surface. And cusps (or scallops) remain at the machined part along the cutter paths and they give the geometrical roughness of the workpiece. Thus, for the good geometrical roughness of the workpiece, it is required very tightly spaced cutter paths in this ball-endmilling process. However, with the tight cutter paths, the geometrical roughness of the workpiece is not regular on the workpiece since the cusp height is variable in the previously developed ISO-parametric or Cartesian machining methods. This paper suggests a method of tool path generation which makes the geometrical roughness of workpiece be constant through the machined surface. In this method, Ferguson Surface design Model is used and cusp height is derived from the instantaneous curvatures. And, to have constant cusp height, an increment of parameter u or v is estimated along the reference cutter path. In ball-end milling experiments, the cusp pattern was examined, and it was proved that the geometrical roughness could be regular by suggested tool path generation method.

• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.82-90
• /
• 1992

To optimize the foam dyeing procedures for polyester and polyester/nylon blended non-woven fabrics, the effects of organic solvents and surfactants were investigated by measuring the foam heights and surface tensions of the foam dyeing solution. The results of the experiments can be summarized as follows: 1) Organic solvents and surfactants (sodium lauryl sulphate: SLS) solution lower the surface tension (ST) of the water, but ST lowering rate of SLS solution is greater than that of solvents. For a 0.25% SLS solution, the minimum surface tension was 30.3 dyne/cm, which is nearly the same value for organic solvents. 2) For 0.25% SLS solutions, additional adding of a 4.0% organic solvent makes the foam height (FH) be its maximum. 3) At 0.6 g/ι dye concentration, incorporation of 0.4% SLS makes the surface tension of the foam solution be its minimum. The foam height did not show any trend due to the dye type. 4) The effect of foam stabilizers (sodium alginate (Alg-Na) and hydroxy ethyl cellulose (HEC)) were also investigated. The foam height of the foaming solution with HEC was greater than that with Alg-Na. The foam stability of the foaming solution with Alg-Na was better than that with HEC.

• Geomechanics and Engineering
• /
• v.6 no.1
• /
• pp.17-31
• /
• 2014

This paper investigates the development of failure surfaces induced by an embankment on soft marine clay deposits and the characteristics of such surfaces through numerical simulations and its comparative study with monitoring results. It is well known that the factor of safety of embankment slopes is closely related to the vertical loading, including the height of the embankment. That is, an increase in the embankment height reduces the factor of safety. However, few studies have examined the relationship between the lateral movement of soft soil beneath the embankment and the factor of safety. In addition, no study has investigated the distribution of the pore pressure coefficient B value along the failure surface. This paper conducts a continuum analysis using finite difference methods to characterize the development of failure surfaces during embankment construction on soft marine clay deposits. The results of the continuum analysis for failure surfaces, stress, displacement, and the factor of safety can be used for the management of embankment construction. In failure mechanism, it has been validated that a large shear displacement causes change of stress and pore pressure along the failure surface. In addition, the pore pressure coefficient B value decreases along the failure surface as the embankment height increases. This means that the rate of change in stress is higher than that in pore pressure.

• 한국해양학회지
• /
• v.29 no.4
• /
• pp.383-391
• /
• 1994

Sea surface height geoidal undulation, and gravity anomaly derived from satellite altimeter measurements are described. Assuming mean sea surface height (MSSH) as geoidal undulation, MSSH was converted to gravity anomaly. the result shows that the gravity anomaly derived from satellite altimeter data can be mapped to an accuracy of the surface ship gravity measurements. The data used for the conversion is the two-year mean sea surface height obtained from GEOSAT Exact Repeat Mission. The conversion was carried out using fast Fourier transform with plane approximation. In this process, the so called remove-restore method was employed.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.15-26
• /
• 2004

The calibration for systematic error in LiDAR is crucial for the accuracy of airborne laser scanning. The main error is the misalignment of platforms between INS(Inertial Navigation System) and Laser scanner For planimetrical calibration of LiDAR, the building is good feature which has great changes in height and continuous flat area in the top. The planimetry error(pitch, roll) is corrected by adjustment of height which is calculated from comparing ground control points(GCP) of building to laser scanning data. We can know scale correction of laser range by the comparison of LiDAR data and GCP is arranged at the end of scan angle where maximize the height error. The area for scale calibration have to be large flat and have almost same elevation. At 1000m for average flying height, The Accuracy of laser scanning data using LiDAR is within 110cm in height and ${\pm}$50cm in planmetry so we can use laser scanning data for generating 3D terrain surface, expecically digital surface model(DSM) which is difficult to measure by aerial photogrammetry in forest, coast, urban area of high buildings

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.6
• /
• pp.605-614
• /
• 2015

Drone imaging, which is more cost-effective and controllable compared to airborne LiDAR, requires a low-cost camera and is used for capturing color images. From the overlapped color images, we produced two high-resolution digital surface models over different test areas. After segmentation, we performed tree identification according to the method proposed by , and computed the tree height and the canopy crown size. Compared with the field measurements, the computed results for the tree height in test area 1 (coniferous trees) were found to be accurate, while the results in test area 2 (deciduous coniferous trees) were found to be underestimated. The RMSE of the tree height was 0.84 m, and the width of the canopy crown was 1.51 m in test area 1. Further, the RMSE of the tree height was 2.45 m, and the width of the canopy crown was 1.53 m in test area 2. The experiment results validated the use of drone images for the extraction of a tree structure.

• Journal of Korean Physical Therapy Science
• /
• v.19 no.1
• /
• pp.55-62
• /
• 2012

Objectives : The purpose of this study was to determine the effects of high heeled shoes on the static & dynamic balance performance and electromyography(EMG) of back and lower extremity muscles. Materials & Methods : Sixteen women participated in this study. Subjects were composed two groups with LL shoes group and higher heel shoes group. We carried out Romberg's test and muscle activity of left and right Paraspinalis, Quadriceps femoris, Tibialis anterior, Gastrocnemius muscles by EMG in order to determine static balance performance according heel height. Using by Biorescue(Incenierie company), we trained subject to transfer of COG each direction(Anterior, posterior, Right, Left), we carried out this test for distance, surface, distance/surface in order to determine dynamic balance performance according heel height. The data were analyzed by independent t-test between lower and high heel height using SPSS(ver. 17.0)/PC program. Results : There was significant difference of distance(p<.05) of weight perturbation between lower and high group in dynamic balance performance and EMG value of left Gastrocnemius(p<.05), both Tibialis anterior(p<.05) muscle in static balance performance. Conclusions : Height of heel has effect on dynamic balance performance in distance of the Anterior, posterior direction. EMG of Gastrocnemius and Tibialis anterior muscles were affected by Romberg's test.