• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2008년도 International Symposium on Remote Sensing
• /
• pp.378-381
• /
• 2008

The regulating and relaxing targets in the Land Use Regulation and Total Maximum Daily Loads are influenced by Land cover information. For the providing more accurate land information, this study attempted to generate an impervious surface map using KOMPSAT-2 image which a Korea manufactured high resolution satellite image. The classification progress of this study carried out by tasseled-cap spectral enhancement through each class extraction technique neither existing classification method. KOMPSAT-2 image of this study is enhanced by Soil Brightness Index(SBI), Green vegetation Index(GVI), None-Such wetness Index(NWI). Then ranges of extracted each index in enhanced image are determined. And then, Confidence Interval of classes was determined through the calculating Non-exceedance Probability. Spectral distributions of each class are changed according to changing of Control coefficient(${\alpha}$) at the calculated Non-exceedance Probability. Previously, Land cover classification map was generated based on established ranges of classes, and then, pervious and impervious surface was reclassified. Finally, impervious ratio of reclassified impervious surface map was calculated with blocks in the study area.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.131-131
• /
• 2000

We witnessed the enhancement of mangetoresistance (MR) in La0.75Ca0.25MnO3 thin films grown on Si (100) substrates by RF magnetron sputtering. The films are polycrystalline with (100) and (110) orientations. The lattice constants of films are reduced as much as 0.9% compared to the one of the bulk sample, which proves that the compressive stress on films was imposed by Si sbustrate. It is found that the MR value (Δ$\rho$/$\rho$0) of films are 0.33, 0.29 and 0.27 under a magnetic field of 1.5T for each films with deposition temperature of $700^{\circ}C$, 75$0^{\circ}C$ and 80$0^{\circ}C$, respectively. The correlation between the MR values and lattice constants of films is discussed. It is concluded that the compressive stress on films cause the enhancement of MR values of thin films grown on Si (1000 substrates. Some mechanism of compressive stress induced by Si substrate is suggested.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.339-342
• /
• 2003

This paper newly proposes a mesh regularization method for the enhancement of the efficiency in sheet metal forming analysis. The regularization method searches for distorted elements with appropriate searching criteria and constructs patches including the elements to be modified. Each patch is then extended to a three-dimensional surface in order to obtain the information of the continuous coordinates. In constructing the surface enclosing each patch, NURBS(Non-Uniform Rational B-Spline) surface is employed to describe a three-dimensional free surface. On the basis of the constructed surface, each node is properly arranged to form unit elements as close as to a square. The analysis results with the proposed method are compared to the results from the direct forming analysis without mesh regularization in order to confirm the validity of the method.

• 소성∙가공
• /
• 제12권4호
• /
• pp.401-407
• /
• 2003

This paper newly proposes a mesh regularization method for the enhancement of the efficiency in sheet metal forming analysis. The regularization method searches for distorted elements with appropriate searching criteria and constructs patches including the elements to be modified. Each patch is then extended to a three-dimensional surface in order to obtain the information of the continuous coordinates. In constructing the surface enclosing each patch, NURBS(Non-Uniform Rational B-Spline) surface is employed to describe a three-dimensional free surface. On the basis of the constructed surface, each node is properly arranged to form unit elements as close as to a square. The state variables calculated from its original mesh geometry are mapped into the new mesh geometry for the next stage or incremental step of a forming analysis. The analysis results with the proposed method are compared to the results from the direct forming analysis without mesh regularization in order to confirm the validity of the method.

• Korean Membrane Journal
• /
• 제1권1호
• /
• pp.43-49
• /
• 1999

Separation of soluble oil was investigated during filtration of cutting oil emulsion using various commercial ultrafiltration membranes. The surface properties of membranes used were hydrophilic hydrophobic and modified surfaces by various surfactant pretreatments. Conditions varied include stirring speed transmeembrane pressure membrane type and surfactant type for pretreatment. The results give some indication of mechanisms occurring at the membrane surface. Surfactant pretreatments significantly improved water flux and UF flux of hydrophilic regenerated cellulose(up to 2.4x for YM100) and hydrophobic polysulfone (up to 2.2x for PTHK) membranes depending on surfactant type and operating conditions. The UF flux enhancement was attributed to membrane swelling and reduction of interfacial surface tension between oil droplets and membrane surface. unexpectedly the hydrophilic membranes revealed greater flux enhancement than the hydrophobic membranes. The results also showed a greater improvement in UF flux at lower operating pressure.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.410-415
• /
• 1999

The adhesion strength of sputtered copper films to Inconel substrates has been studied using the scratch test. The effects of substrate treatments before deposition such as chemical or ion bombardment etching were investigated by means of a mean critical load derived from a Weibull-like statistical analysis. It was found that the mean critical load was very weak unless the amorphous layer produced by mechanical polishing on the substrate surface was eliminated. Chemical etching in a nitric-hydrochloric acid bath was shown to have practically no effect on the enhancement of the adhesion. In contrast, the addition in this bath of nickel and copper sulphates allowed removal of the amorphous layer and an increase in the values of the mean critical load. However, it was observed that excessive chemical etching could cancel out the mean critical load enhancement. The results obtained in the case of ion bombardment etching pretreatments could be far higher than those obtained with chemical etching. Moreover, for a sufficiently long period of ion bombardment etching, the adhesion strength was so high that it was impossible to observe evidence of an adhesion failure.

• Membrane and Water Treatment
• /
• 제1권4호
• /
• pp.253-271
• /
• 2010

A theoretical study for the flux enhancement by pulsation of transmembrane pressure is presented for osmotic pressure controlled ultrafiltration under laminar flow regime. The transient velocity profile is solved analytically using Green's function method. Time dependent convective diffusive equation is solved to quantify the membrane surface concentration and the permeate flux, numerically. The effects of the amplitude and frequency of pulsation on flux, surface concentration and observed retention are studied.

• 대한기계학회논문집B
• /
• 제34권2호
• /
• pp.203-212
• /
• 2010

수분류 스프레이 냉각은 많은 산업적인 응용분야에 넓게 사용되고 있다. 본 연구는 수분류 스프레이가 표면거칠기가 주어진 $900^{\circ}C$ 고온강판의 표면에 충돌하는 경우, 열유속 및 열전달계수의 정량적인 측정을 통해 표면거칠기가 수분류 스프레이 냉각에 미치는 영향을 고찰하였다. 이 때의 국소 열유속은 시편, 카트리지히터, 열전대의 조합으로 고안된 고유의 열유속게이지를 제작하여 엄밀하게 측정되었다. 평균 표면거칠기 높이를 기준으로 40, 60, $80{\mu}M$의 3 가지 표면과 매끈한 표면에 대한 수분류 스프레이 냉각 의 열전달 현상이 비교 및 평가되었다. 표면거칠기가 주어진 표면에서의 돌출물은 얇은 열 경계층두께를 통과할 수 있기 때문에 표면거칠기가 주어진 경우에 열전달은 뚜렷하게 증가하였고, 표면거칠기의 의한 열전달 향상 기구는 서로 다른 비등영역에 대해 구분하여 조사되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.392-392
• /
• 2010

In this study, high-speed chemical dry thinning process of Si wafer and evolution of surface roughness were investigated. Direct injection of NO gas into the reactor during the supply of F radicals from $NF_3$ remote plasmas was very effective in increasing the Si thinning rate due to the NO-induced enhancement of surface reaction but thinned Si surface became roughened significantly. Addition of Ar gas, together with NO gas, decreased root mean square (RMS) surface roughness of thinned Si wafer significantly. The process regime for the thinning rate enhancement with reduced surface roughness was extended at higher Ar gas flow rate. Si wafer thinning rate as high as $22.8\;{\mu}m/min$ and root-mean-squared (RMS) surface roughness as small as 0.75 nm could be obtained. It is expected that high-speed chemical dry thinning process has possibility of application to ultra-thin Si wafer thinning with no mechanical damage.

• 한국항공우주학회지
• /
• 제34권12호
• /
• pp.59-66
• /
• 2006

하이브리드 로켓 연료의 연소율 향상을 위한 나선형 홈이 유동 특성에 미치는 영향을 규명하기 위하여 난류 증가와 선회 유동 발생에 대한 수치계산을 수행하였다. 나선형 튜브의 열전달 관계식을 이용하여 여러 형상의 나선형 홈이 있는 연료의 열전달 향상을 예측하였으며 연소율 측정값과 비교하여 상호 연관성을 확인하였다. 실험 결과와 열전달 향상 예측 값은 동일한 경향을 나타내더라도 수치는 큰 차이를 나타냈는데 이것은 연료가 연소하기 위하여 기화할 때 발생하는 분출속도가 존재하기 때문이다. 분출효과를 고려하여 RANS 계산을 수행한 결과, 난류에너지는 상당히 증가한 반면 선회 수는 조금 증가하는 결과를 보여 주었다. 그럼에도 불구하고 나선형 홈에 의한 난류 증가 또는 선회유동 생성은 연소율을 증가시키는 중요한 메커니즘임이 밝혀졌다. 그러나 분출로 인하여 난류에너지가 증가되어도 열전달 향상에 기여하지 못하는 것으로 확인되었는데 이것은 분출 속도가 표면의 경계층을 밀어내어 대류 열전달이 증가되는 것을 차단하기 때문인 것으로 밝혀졌다.