• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.91-95
• /
• 1997

ESPI(Electronic Speckle Pattern Interferometry) is new optical measuring method to be able to measure the surface deformations of engineering components and materials in industrial areas. Conventional measuring method of surface deformation such as the strain gauge have many demerits because it is contact and point-to-point measuring one. But ESPI that is non-contact, whole field measuring method can overcome previous disadvantages. The speckle pattern to be formed with interference phenomena of scattering light from rough surfaces illuminated by laser light have phase information of surface In this study we used this interference phenomena and the phase shifting method to measure the in- plane deformation, together with the use of digital equipment to process the information contained in the speckle pattern and to display consequent inter ferograms. Finally we obtained good agreement between the experimenta results and those of FEM..

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1410-1413
• /
• 2003

Drawing is a basic plastic deformation method and productive manufacturing process make wire. rod and variety section geometry bar. Study for the rod drawing process of rod was researched long littles. but non-axisymmetric drawing process is weak. So metal flow is very irregular in non-axisymmetric drawing process and difficult to define about material deformation generally. In this paper, to solve material deformation, use finite element method and then define suitable shape for rod to hexagonal drawing dies. And research corner filling rate and surface roughness for the high strength steel hexagonal bar produced defined dies.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.3
• /
• pp.334-341
• /
• 1998

This paper proposes an algorithm to obtain the time-to-contact between an observer and a target and surface orientation of the target. These two physical elements are computed from the image deformation of a known shape, which is extracted by supervised classification of detected line segments based on MAP and Mahalanobis distance. The proposed algorithm was applied to the natural outdoor traffic scene and would contribute to the development for a collision avoidance system.

• Korean Journal of Optics and Photonics
• /
• v.24 no.6
• /
• pp.324-330
• /
• 2013

Phase-measuring deflectometry is a full-field gradient measuring technique that lends itself very well to testing specular optical surfaces. We have measured deformation of a large specular surface by deflectometry. In this work, we have used a Fourier-transform method to get the phase from a measured deformed fringe pattern, and we have used least squares method to obtain the height information of the specular surface from the calculated slope. Experimentally, we have confirmed that deflectometry can be used for deformation measurement of a specular surface like that of a wafer.

• Advances in nano research
• /
• v.15 no.2
• /
• pp.165-174
• /
• 2023

The study investigated the effect of geometric structures of nano-patterned surfaces, such as peak sharpness, height, width, aspect ratio, and spacing, on mechano-bactericidal properties. Here, in silico models were developed to explain surface interactions with Escherichia coli. Numerical solutions were performed based on the finite element method and verified by the artificial neural network method. An E. coli cell adhered to the nano surface formed elastic and creep deformation models, and the cells' maximum deformation, maximum stress, and maximum strain were calculated. The results determined that the increase in peak sharpness, aspect ratio, and spacing values increased the maximum deformation, maximum stress, and maximum strain on E. coli cell. In addition, the results showed that FEM and ANN methods were in good agreement with each other. This study proved that the geometrical structures of nano-patterned surfaces have an important role in the mechano-bactericidal effect.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.94-101
• /
• 1996

This paper presents an investigation of the ability of the scheme to simultaneously accomplish both prediction of fracture initiation and analysis of deformation in cold forged products. The Cockcroft-Latham criterion which is successfully applied to a variety of loading situations is used in the present investigation to estimate if and where surface and internal fracture occur during the deformation process. The numerical predictions and experimental results of two types of fundamental cold metal forming process taken into account are compared. Finite element simulation combined with fracture criterion has successfully predicted the site of surface or internal fracture initiation and corresponding to level of deformation observed experimentally.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.546-551
• /
• 1997

In sheet metal forming, since the surface area of workpiece is apparently larger than the volume of it, the surface condition of the sheet metal is much varied. The formability of sheet metal is decided by the forming limit and the macroscopic suface defect as like fracture and wrinkle, and microscopic asponent, The factors affected in forming limit are stain herdening exponent, strain-rate scnsitivity exponent, anisotropic coefficient. The increasing of surface roughness is decresed the forming limit curve. It is known that the greater plastic deformation the more surface roughness by Kienzle, Osadaka. The purpose of this study is to investigate the influences of surface roughness in a uniaxial tension and the traperzoidal-shaped box drawing.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.49-56
• /
• 1998

The thermal deformation of the contact seal components has been analyzed using the finite element method. The temperature distributions, the thermal deformations and contact stresses are solved numerically for the contact surface with wear coning effects. The thermal deformation is always shown to distort the sealing surface along the radius of the seal ring. The results show that the deformations of inner radius side are significant compared with those of outer radius. Thus, the thermal deformation due to thermal heatings may promote the coned face wear or wear related thermal cracks at the contacting face of the seal ring component.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.448-451
• /
• 2005

An aspheric mirror, which requires less than $\lambda/2\;(\lambda=632.8nm)$ of form error for the $\phi$ 200mm reference curved surface, has been manufactured with an ultra-precision turning machine. We have known through several tests that the deformation patterns of the reflecting surface is related with bolting positions. In this paper the effect of main factors on deformation of a reflector is studied with a FE code. The considered factors are angular velocity, natural frequencies for a mirror, temperature increment during machining. The obtained test results are similar to the deformation shape due to the assumed temperature increment.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.84-91
• /
• 2010

Heat treatment with carburized quenching process is widely used for automotive helical gear to improve its surface properties of hardness and strength. However, the gear can be deformed with the process over the allowable tolerance, which possibly makes noise, vibration and heat problems in operation. In this study, deformation of helical gear during heat treatment of carburized quenching was analyzed with a numerical method, incorporating coupled calculations of thermal conduction, carbon diffusion, phase transformation and thermal stresses. With the analysis, the effect of coolant temperature in quenching on the deformation was investigated. The result of the analysis revealed that the higher the coolant temperature became, the more change of helix angle and the more compressive stresses in the surface generated, because of delayed generation of martensite in the part.