• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.418-422
• /
• 2005

The degradation of IPA according to coating conditions was examined by $TiO_{2}$/p-25-coated aluminium metal plate. Inorganic(KR-400), inorganic$\cdot$ organic hybrid(TMOS) and organic(A-9540) resins were used as binder $TiO_{2}$ coated surface of aluminum metal plate was clear with all binders, and the adhesion of binders was good except inorganic binder. The activity for IPA degradation appeared to range in order A-9540>TMOS>KR-400. The optimum activity was obtained when the ratio of TMOS and P-25 was 1.6:10, and when the ratio of A-9540 and P-25 was 1.0:6.0, respectly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.33-36
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina $(Al_2O_3)$ abrasive containing slurry with 5 % $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with 5 % $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.243-253
• /
• 1998

PVC membrane, which has been used for membrane of electrolyte sensors, shortened sensor lifetime due to poor adhesion to sensor surface and exhibited difficulty in standardization and mass-production. To overcome these problems, the membrane solution was prepared with neutral carrier, matrix(TEOS:DEDMS=1:3), solvent(ethanol), and a catalyzer(HCl). The fabricated electrolyte sensors showed typical electrical characteristics of MISFET (metal-insulator-semiconductor field-effect transistor). The K-, Ca- and Na-ISFETs showed sensitivity of 53, 25 and 50 mV/decade in wide concentration range, respectively. The response time was about 90 seconds and the drift was 0.05mV/hour. These results suggest that the sol-gel method and the lift-off technique can be applied to formation of membranes and expected to improve mass-productivity, standardzation of the sensors.

• Restorative Dentistry and Endodontics
• /
• v.29 no.3
• /
• pp.205-211
• /
• 2004

This study evaluated the microleakage and interfacial gap between enamel and composite resin under the dry and wet condition of the enamel surface. V shaped class 5 cavities were prepared on the occlusal portion of extracted human molars. Samples were divided into three groups：D group (air dry for 10-15s), BD group (blot dry with moist cotton pellet), and DR group (air dry for 10-15s and rewet with Aqua-Prep F for 20s), Cavities were filled using Aelitefil composite resin after applied One-Step. Microleakage was tested by 2% methylene blue dye solution and the data were statistically analysed by Kruskal-Wallis test and Mann-Whitney test. Also Enamel-resin interface was observed under SEM. Group BD showed statistically lower microleakage than group D (p < 0.05). but there was no statistically significant difference between group BD and DR (p > 0.05). At the enamel-resin interface, group D showed the gap of $2{\;}{\mu}m$ thickness, but group BD and DR showed close adaptation. In conclusion, the use of blot dry and rewetting agent (Aqua-Prep F) resulted in decreased microleakage and improved adhesion between enamel and resin when using One-Step.

• Polymer(Korea)
• /
• v.28 no.5
• /
• pp.374-381
• /
• 2004

Gas permeability of low density polyethylene (LDPE) film containing zeolite powder for $CO_2,\;O_2$ and $N_2$ were investigated. Zeolite powders modified by cations or surfactant were compounded with LDPE to produce $20 wt\%$ masterbatch. After blending the masterbatch with LDPE, zeolite filled films were prepared by the blown film process. Finally, the composite films containing zeolite loadings of 0, 3,5, and $10 wt\%$ were produced. A gas permeability apparatus based on the variable volume principle was designed to analyze the characteristics of films. Experiments showed a general trend that gas permeabilities first decreased and then increased as the zeolite content was increased. Surfactant modified zeolite showed a better interfacial adhesion with the matrix, but the film did not show a discernible difference in gas permeability compared with the other modified films. The difference of temperature dependences in the gas permeabilities of composite films was slightly smaller than that of LDPE film.

• Journal of Veterinary Clinics
• /
• v.25 no.6
• /
• pp.494-500
• /
• 2008

The aim of this study was to determine the effectiveness of hyaluronic acid-carboxymethylcellulose membrane (GUARDIX-$MB^{(R)}$) barriers on prevention against post-operative peritoneal adhesions. In this study, fourteen mongrel dogs were divided into two experimental groups: 0.1 % hyaluronic acid (0.1HA) group and hyaluronic acidcarboxymethylcellulose membrane (HA-CMC) group. In order to induce adhesions, the anti-mesenteric serosa of the ileum was exteriorized and then abraded in a standard manner by scraping with a scalpel blade to create homogenous petechial hemorrhagic surface over a $1\;{\times}\;1cm$ area. Solution of 0.1HA were simply coated over the abraded tissues, $1.5\;{\times}\;1.5cm$ HA-CMC membrane was placed over the abraded tissues, allowed to spread across the intra-abdominal organs before closure of the abdomen. On day 1 before and day 1, 4, 7, 14, and 21 after operation, venous blood specimens were collected for measurement of fibrinogen and total WBC. The adhesions were blindly assessed 3 weeks later by using a computerized tensiometer. The fibrinogen and total WBC values of two groups showed no statistical significances. The mean tensile strength (gram force, gf) of formed adhesions day 21 after surgery was $88.1\;{\pm}\;55.70gf$ in the 0.1 % HA group and $24.8\;{\pm}\;22.69gf$ in the HA-CMC group. The tensile strength values of adhesion separation HA-CMC membrane group was significantly lower than the 0.1HA group (p<0.05). Therefore, we suggest that HACMC membrane reduce peritoneal adhesions may be applicable to preventing post-operative intraperitoneal adhesions in dogs.

• Korean Journal of Materials Research
• /
• v.19 no.7
• /
• pp.349-355
• /
• 2009

Metal thin film patterns on a LTCC substrate, which was connected through inner via and metal paste for electrical signals, were formed by a screen printing process that used electric paste, such as silver and copper, in a conventional method. This method brought about many problems, such as non uniform thickness in printing, large line spaces, and non-clearance. As a result of these problems, it was very difficult to perform fine and high resolution for high frequency signals. In this study, the electric signal patterns were formed with the sputtered metal thin films (Ti, Cu) on an LTCC substrate that was coated with protective oxide layers, such as $TiO_2$ and $SiO_2$. These electric signal patterns' morphology, surface bonding strength, and effect on electro plating were also investigated. After putting a sold ball on the sputtered metal thin films, their adhesion strength on the LTCC substrate was also evaluated. The protective oxide layers were found to play important roles in creating a strong design for electric components and integrating circuit modules in high frequency ranges.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.21 no.3
• /
• pp.709-713
• /
• 2007

Basement membranes (BMs) are extracellular matrices associated with epithelia, endothelia, muscle, fat and peripheral nerve. They are involved in cell survival, migration, differentiation. BMs functions also include tissue formation and provide mechanical stability as a selective barriers. Laminins are heterotrimeric glycoproteins found in BMs and have a crucial role in cell adhesion and signalling. Madin-Darby canine kidney (MDCK) cells are the best established mammalian model for studying epithelial cell biology The cells form an epithelial monolayer, with tight junctions separating an apical surface from a basolateral membrane facing the filter support and neighboring cells. In this study, using MDCK cells, the synthesis of the BM protein such as laminin with or without methanol extract of Chrysanthemum morifolium (CM) stimulation was analyzed by immunoblotting and CM showed significant increased cell density and enhanced synthesis of laminin.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.1
• /
• pp.108-115
• /
• 2020

In this study, the flexural performance of Highly Ductile Cement Composites(HDCC) mimicking boundary conditions of shellfish skin layer was evaluated. To improve ductility by mimicking the boundary skin layer structure of shellfish, the method of stratification by charging between precast panels using HDCC and the method of distributing PE-mesh to the interface surface were applied. Evaluation of flexural performance of layered cement composite materials mimicking boundary conditions of shellfish skin layer resulted in increased ductility of all test specimens applied with stratified cross-section compared to typical bending test specimens. The layered method by inserting PE-mesh showed excellent ductility. This is most likely because the inserted PE-mesh made an interface for separating the layers while the HDCC pillars in the PE-mesh gave adhesion between layers.

• Journal of Radiation Industry
• /
• v.3 no.1
• /
• pp.7-11
• /
• 2009

Hard magnet was usually used by coating $SiO_2$ ceramic thick films followed by the thermal annealing process. In this work, the alternative annealing process for NdFeB magnets using e-beam sources (1~2 MeV, 50~400 kGy) was investigated. NdFeB magnets was coated with ceramic thick films using the spray method. The optimal annealing parameter for e-beam source reveals to be 1 MeV and 300 kGy. The sample prepared at 1 MeV and 300 kGy was characterized by the analysis of the surface morphology, film hardness, adhesion and chemical stability. The mechanical property of thick film, especially film hardness, is better than that of thermal annealed samples at $180^{\circ}C$. As a result, e-beam annealing process will be one of candidate and attractive heat treatment process. In future, manufacturing process will be carried out in cooperation with the magnet company.