• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.6
• /
• pp.504-510
• /
• 2002

Recently, thin film capacitors of high dielectric constant and low leakage current are applied to integrated devices. In this study, (Ba, Sr)$TiO_3$ (BST) thin films for low cost were prepared by Sol-Gel method. BST solution was spin-coated on Pt/$SiO_2$/Si substrate at 4,000 rpm for 10 seconds. Coating process was repeated 3 times and then sintered at $700^{\circ}C$ for 30 minutes. Structural and electrical characteristics of each specimen were analyzed by TG-DTA, SEM, fractal phenomenon, voltage-current and dielectric factor. Thickness of BST ceramics thin films are about 2,600~2,800 ${\AA}$ at depositing 3 times. Dielectric constant of thin films was decreased in 1 kHz~1 MHz. Dielectric constant and loss to frequency were 250 and 0.02 in $(Ba_{0.7}Sr_{0.3})TiO_3$ (BST3). Leakage current of BST3 was $10^{-9}\sim10^{-11}$/ A under 3 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.14-16
• /
• 1995

Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ ceramic thin films were fabricated from an alkoxide-based solution by Sol-Gel method. Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ co-ramic thin films were formed by spin coating method on Pt/$SiO_2$/Si substrate at 4000[rpm] for 30 [sec]. Coated specimens were dried on the hot-plate at 400[$^{\circ}C$] for 10[min]. The coating process was repeated 6 times and then sintered at temperature between 500 ~ 800[$^{\circ}C$] for 1 hour. The ferroelectric perovskite phases precipitated under the sintering of 700[$^{\circ}C$] for 1 hour. Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ thin film sintered at 700[$^{\circ}C$] for 1hour showed good dielectric constant (2133) and dielectric loss (2.2[%]) Properties. The switching voltage, switching time and leakage currents density were 3.0[V], 1.7[${\mu}$sec] , 160[pA/$\textrm{cm}^2$] repectively.

• Journal of electromagnetic engineering and science
• /
• v.4 no.4
• /
• pp.143-149
• /
• 2004

This paper describes characteristics of the single-balanced low IF resistive FET mixer for the digital beam forming(DBF) receiver. This DBF receiver based on the direct conversion method is designed with Low IF I and Q channel. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(IF) considered in this research are 1950 MHz, 1940 MHz and 10 MHz, respectively. Super low noise HJ FET of NE3210S01 is considered in design. The measured results of the proposed mixer are observed IF output power of -22.8 dBm without spurious signal at 10 MHz, conversion loss of -12.8 dB, isolation characteristics of -20 dB below, 1 dB gain compression point(PldB) of -3.9 dBm, input third order intercept point(IIP3) of 20 dBm, output third order intercept point(OIP3) of 4 dBm and dynamic range of 30 dBm. The proposed mixer has 1.0 dB higher IIP3 than previously published single-balanced resistive and GaAs FET mixers, and has 3.0 dB higher IIP3 and 4.3 dB higher PldB than CMOS mixers. This mixer was fabricated on 0.7874 mm thick microstrip $substrate(\varepsilon_r=2.5)$ and the total size is $123.1\;mm\times107.6\;mm$.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.329-334
• /
• 2005

In this paper, the characteristics of linealy bent wire antennas are first analyzed for shortening straight wire antennas. The results are appropriately applied to the design of the integrated zigzag dipole antenna. Since the integration give rise to discontinuities due to line width, the integrated parasitics are properly attached to both sides of substrate for improving the antenna gain and return loss. The design results are verified with experiments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.739-745
• /
• 2009

This paper presents a design for trapezoidal planar UWB(Ultra Wide-band) antenna using symmetry meander line to realize broad bandwidth at low frequency region. The size of proposed design antenna is $15.5{\times}21{\times}1.6mm^3$ and dielectric substrate considered in design has 4.4 of relative permittivity. The calculated bandwidth is from 1.31 GHz to 10.83 GHz and the measured return loss is 1.5 GHz to 10.6 GHz at -10 dB below, and satisfies with the UWB antenna's bandwidth. The simulated and measured radiation patterns show fine agreement with each other at each frequency.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.2
• /
• pp.21-27
• /
• 2014

In this paper, a planar sleeve monopole antenna for indoor digital TV reception is presented. The antenna has broadband property with the planar monopole and ground of sleeve. Sleeve monopole and ground conductors of the antenna are on the same plane, and exited through CPW feeding. Sleeve monopole and ground of proposed antenna exist on coplanar plane, and excite as CPW. It used FR4 epoxy dielectric substrate of ${\varepsilon}r=4.4$, and the size is $20[mm]{\times}170[mm]{\times}1.6[mm]$ dimension. So the internal antenna is suitable. The measurement results of the fabricated antenna, return loss is larger than -10 [dB] in 470~806 [MHz]. Maximum gain is 0.59 [dBi] on E-plane at 810 MHz and 1.70 [dBi] on H-plane at 640 [MHz]. Radiation pattern is about the same that of dipole antenna at all frequency.

• BMB Reports
• /
• v.28 no.2
• /
• pp.138-142
• /
• 1995

An anticoagulant/fibrinolytic protease was purified to homogeneity from the earthworm Lumbricus rubellus. The protein was a single chain glycoprotein of 32 kDa that exhibited strong proteolytic activity on human thrombin and fibrin clots. Proteolytic degradation of these plasma proteins by the purified enzyme occurred at a neutral pH range. Among several human plasma proteins tested as possible substrates for the protease reaction, the 32 kDa enzyme specifically hydrolyzed both thrombin and fibrin polymers without affecting other proteins, such as serum albumin, immunoglobulin, and hemoglobin. Treatment of the purified enzyme at neutral pH with either phenylmethylsulfonylfluoride or soybean trypsin inhibitor resulted in a loss of catalytic activity. The enzyme hydrolyzed the chromogenic substrate H-D-Phe-L-Pipecolyl-L-Arg-p-nitroanilide with a $K_m$ value of 1.1 ${\mu}M$ at a neutral pH. These results suggest that the anticoagulant/fibrinolytic enzyme from Lumbricus rubellus is a member of the serine protease family having a trypsin-like active site, and one of the potential clevage sites for the enzyme is the carbonyl side of arginine residues in polypeptide chains.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.935-940
• /
• 2009

In this research, the composites (100-x)LCP-xBNT (x = 0, 10, 20, 30, 40 vol.%) were fabricated with thermoplastic LCP(Liquid Crystal Polymer) and BNT($BaNd_2Ti_4O_{12}$) which is a high frequency dielectric material. Their dielectric properties, mechanical strength and microstructure were investigated by Impedance analyser, Instron and SEM. In order to fabricate LCP-BNT composites, LCP resin was put into the twin screw type mixer($310^{\circ}C$), melted by keeping for 10 min. After that, BNT filler was dispersed with melted LCP resin for 15 min. in the mixer. For measuring the dielectric properties and mechanical strength, Composite specimens were made by pressing composite granule (LCP-BNT) with 7 ton in the mold at $310^{\circ}C$. With increasing the BNT content (0~40 vol.%) of the composite, Its dielectric constant increased, dielectric loss and flexural strength decreased. The dielectric constant and flexural strength of composites with 20~30 vol.% of BNT filler are 4.1~6.0 and 35~55 MPa respectively. BNT/LCP composite is the potential substrate material for the high frequency application.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2016

In this paper, the compact CPW-fed slot antenna for WLAN applications is proposed. While the proposed antenna with size of only $20{\times}18{\times}1mm^3$ is consisted of double stub and folded slot, the antenna for 2.4 GHz band and 5 GHz band is designed and fabricated with optimized parameters obtained by simulation. Proposed antenna is fabricated with FR-4 substrate to the thickness of 1.0 mm. By obtaining the measured return loss level of < -10 dB at dual-band, we showed that it is operated as antenna for WLAN applications, and then it is also expected to be usable as antenna for RFID.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.153-156
• /
• 2003

We have studied fabrication of $MgB_2$ thin film on $SrTiO_3$ (001) and r-cut $A1_2$$O_3$ substrates by rf magnetron sputtering method using and $ MgB_2$ single target and two targets of Mg and B, respectively. Based on P -T phase diagram of $MgB_2$ and vapor pressure curves of Mg and B, a three-step process was employed. B layer was deposited at the bottom to enhance the film adhesion to the substrate. Secondly, co-sputtering of Mg and B was done. Finally, Mg was sputtered on top to compensate fur the loss of Mg during annealing. Subsequently, $MgB_2$ films were in-situ annealed in various conditions. The sample fabricated using the three-step process showed $T_{c}$ of 24 K and formation of superconducting $MgB_2$ phase was confirmed by XRD spectra. In case of co-sputtering deposition, $T_{c}$ depended on annealing time and argon pressure. However, those made by single-target sputtering showed non-superconducting behavior or low transition temperature, at best.est.