• Bulletin of the Korean Chemical Society
• /
• v.18 no.1
• /
• pp.56-61
• /
• 1997

Lead zirconate titanate (PZT) thin fills were deposited onto the Pt/Ti/SiO2/Si substrate by the pulsed laser deposition with the second harmonic wavelength (532 nm) of Nd:YAG laser. In order to determine the optimum conditions for the film deposition, the phase of the films were investigated as functions of ambient oxygen pressure, substrate temperature, and laser fluence. Also the chemical composition analysis was conducted for the PZT films deposited under various ambient oxygen pressure. When the distance between substrate and bulk PZT target is set to 20 mm, the optimum conditions have been determined to be 3 torr of oxygen pressure, 1.5 J/cm2 of laser fluence, and 823-848(±10) K range of substrate temperature. At these conditions, perovskite phase PZT films were obtained on platinized silicon. The chemical composition of the films is very similar to that of PZT bulk target. The physical structure of the deposited films analyzed by scanning electron microscopy shows a columnar morphology perpendicular to the substrate surface. Capacitance-Voltage hysteresis loop measurements show also a typical characteristics of ferroelectric thin film. The dielectric constant is found to be 528 for the 0.48 μm thickness of PZT thin film.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.2
• /
• pp.96-101
• /
• 2022

The effects of the growth temperature on the structural, optical, and morphological properties of BaWO₄:Sm³⁺ phosphor thin films were investigated. The BaWO₄:Sm³⁺ thin films were grown on quartz substrates at several growth temperatures by radio-frequency magnetron sputtering. All the thin films crystallized in a tetragonal structure with a main BaWO₄ (112) diffraction peak. The 830 nm-thick BaWO₄:Sm³⁺ thin films grown at 300 ℃ exhibited numerous polygon-shaped particles. The excitation spectra of BaWO₄:Sm³⁺ thin films consisted of a broad excitation band in the 200-270 nm with a maximum at 236 nm due to the O^2--Sm³⁺ charge transfer and two small bands peaked at 402 and 463 nm, respectively. Under 236 nm excitation, the BaWO₄:Sm³⁺ thin films showed an intense red emission peak at 641 nm due to the ⁴G_5/2→⁶H_9/2 transition of Sm³⁺, indicating that the Sm³⁺ ions occupied sites of non-inversion symmetry in the BaWO₄ host lattice. The highest emission intensity was observed for the thin film grown at 300 ℃, with a 51.8% transmittance and 5.09 eV bandgap. The average optical transmittance in the wavelength range of 500-1100 nm was increased from 53.2% at 200 ℃ to 60.8% after growing at 400 ℃. These results suggest that 300 ℃ is the optimum temperature for growing redemitting BaWO₄:Sm³⁺ thin films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.507-507
• /
• 2013

유리기판으로 투과되는 빛들 중에는 내부 전반사나 wave-guided mode로 인하여 손실이 일어나 일반적으로 20%의 광추출 효율을 가진다. 이러한 문제점을 해결하기 위한 연구에는 Photonic Crystal과 같은 주기적인 나노 구조물이 있는데 이러한 구조물을 제작하기 위한 마스크 공정 과정은 대부분 복잡하거나 비싼 단점이 있다. 이에 본 발표에서는 마스크 없이 비정질소다라임 유리의 구조물 생성으로 광 추출 효율이 상승하는지 보고자 하였다. M-ICP (Magnetized-Induced Coupled Plasma)란 용량 결합형 플라즈마와 유도 결합형 플라즈마 두 가지 방식의 플라즈마를 이용한 것인데 용량 결합형 플라즈마를 이용해 이온이 sheath에 의해 가속되어 유리표면에 부딪히고 그에 따라 유리가 식각되는 물리적 식각을 이용하였다. 또한 이온의 밀도를 조절하기 위해 유도결합형 플라즈마 방식을 이용하여 식각률을 높였다. 화학적 식각을 위해서는 CF4와 O2혼합 가스를 이용해 F가 Si와 결합하여 SiF4가 되어 사라지고 탄소잔여물인 C는 O2와 반응하여 제거하였다. 그 결과, 랜덤한 분포를 가지는 미세한 구조물(stochastic sub-wavelength structure)을 유리 표면에 형성할 수 있었고, 또한 다양한 가스 종류와 압력, source power와 bias power, 그리고 시간을 바꿔가며 미세 구조물들을 관찰하였다. 실험 결과, 가시광선 파장 이하의 높이를 갖고 수 마이크로미터의 너비를 갖는 구조물이 전반사되는 빛을 효율적으로 추출하는 것을 산란되는 빛의 정도인 diffusive transmittance 가 기존 0%에서 15% 정도로 증가하는 것으로 스펙트로포토미터 측정을 통해 확인하였다. 이러한 유리 기판 위 구조물 생성방법을 OLED에 적용한다면 적은 비용으로 소자의 효율을 크게 향상 시킬 수 있을 것이다. 또한 본 처리 과정의 장점은 기존의 방법에 필요한 스퍼터링이나 RTA 처리 과정이 필요 없어 공정 단가 절감과 제조 공정의 단순화로 높은 생산성을 얻을 수 있으며 대면적화에도 유리하다.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.1
• /
• pp.7-10
• /
• 2003

Single phase CuInS$_2$ thin film with the strongest diffraction peak (112) at diffraction angle (2$\theta$) of 27.7$^{\circ}$ and the second strongest diffraction peak (220) at diffraction angle (2$\theta$) of 46.25$^{\circ}$was well made with chalcopyrite structure at substrate temperature of 70$^{\circ}C$. annealing temperature of 250$^{\circ}C$, annealing time of 60 min. The CuInS$_2$ thin film had the greatest grain size of 1.2 Um when the Cu/In composition ratio of 1.03, where the lattice constant of a and c were 5.60${\AA}$ and 11.12${\AA}$, respectively. The Cu/In stoichiometry of the single-phase CuInS$_2$thin films was from 0.84 to 1.3. The film was p-type when tile Cu/In ratio was above 0.99 and was n-type when the Cu/In was below 0.95. The fundamental absorption wavelength, absorption coefficient and optical band gap of p-type CuInS$_2$ thin film with Cu/In=1.3 were 837nm, 3.OH 104 cm-1 and 1.48 eV, respectively. The fundamental absorption wavelength absorption coefficient and optical energy band gap of n-type CuInS$_2$ thin film with Cu/In=0.84 were 821 nm, 6.0${\times}$10$^4$cm$\^$-1/ and 1.51 eV, respectively.

• Korean Journal of Materials Research
• /
• v.22 no.3
• /
• pp.145-149
• /
• 2012

Red phosphors of $Gd_{1-x}Al_3(BO_3)_4:{Eu_x}^{3+}$ were synthesized by using the solid-state reaction method. The phase structure and morphology of the phosphors were measured using X-ray diffraction (XRD) and field emission-scanning electron microscopy (FE-SEM), respectively. The optical properties of $GdAl_3(BO_3)_4:Eu^{3+}$ phosphors with concentrations of $Eu^{3+}$ ions of 0, 0.05, 0.10, 0.15, and 0.20 mol were investigated at room temperature. The crystals were hexagonal with a rhombohedral lattice. The excitation spectra of all the phosphors, irrespective of the $Eu^{3+}$ concentrations, were composed of a broad band centered at 265 nm and a narrow band having peak at 274 nm. As for the emission spectra, the peak wavelength was 613 nm under a 274 nm ultraviolet excitation. The intensity ratio of the red emission transition ($^5D_0{\rightarrow}^7F_2$) to orange ($^5D_0{\rightarrow}^7F_1$) shows that the $Eu^{3+}$ ions occupy sites of no inversion symmetry in the host. In conclusion, the optimum doping concentration of $Eu^{3+}$ ions for preparing $GdAl_3(BO_3)_4:Eu^{3+}$ phosphors was found to be 0.15 mol.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.2
• /
• pp.45-50
• /
• 2022

Ga₂O₃ thin films were grown on n-type Si substrates at various growth temperatures of 500, 550, 600, 650 and 700℃. The Ga₂O₃ thin films grown at 500℃ and 550℃ were characterized as featureless flat surface. Grown at higher temperatures (600, 650, and 700℃) showed very rough surface morphology. To figure out the annealing effect on the thin films grown at relatively low temperatures (500, 550, 600, 650 and 700℃), the Ga₂O₃ films were thermally treated at 900℃ for 10 minutes. Crystal structure of the Ga₂O₃ films grown at 500 and 550℃ were changed from amorphous to polycrystalline structure with flat surface. Ga₂O₃ film grown at 550℃ was chosen for the fabrication of a Schottky barrier diode (SBD). Electrical properties of the SBDs depend on the thermal treatment were evaluated. A MSM type photodetector was made on the low temperature grown Ga₂O₃ thin film. The photocurrent for the illumination of 266 nm wavelength showed 5.32 times higher than dark current at the operating voltage of 10 V.

• Korean Journal of Materials Research
• /
• v.18 no.2
• /
• pp.92-97
• /
• 2008

In spray pyrolysis, the effects of the preparation temperature, flow rate of the carrier gas and concentration of the spray solution on characteristics such as the morphology, size, and emission intensity of $Ca_8Mg(SiO_4)_4Cl_2:Eu^{2+}$ phosphor powders under long-wavelength ultraviolet light were investigated. The phosphor powders obtained post-treatment had a range of micron sizes with regular morphologies. However, the composition, crystal structure and photoluminescence intensity of the phosphor powders were affected by the preparation conditions of the precursor powders. The $Ca_8Mg(SiO_4)_4Cl_2:Eu^{2+}$ phosphor powders prepared at temperatures that were lower and higher than $700^{\circ}C$ had low photoluminescence intensities due to deficiencies related to the of Cl component. The phosphor powders with the deficient Cl component had impurity peaks of $Ca_2SiO_4$. The optimum flow rates of the carrier gas in the preparation of the $Ca_8Mg(SiO_4)_4Cl_2:Eu^{2+}$ phosphor powders with high photoluminescence intensities and regular morphologies were between 40 and 60 l/minute. Phosphor powders prepared from a spray solution above 0.5 M had regular morphologies and high photoluminescence intensities.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.925-928
• /
• 2010

Nitrogen-doped $TiO_2$ ($TiO_2$:N) nano-particles with a pure anatase crystalline structure were successfully synthesized through the hydrolysis of $TiCl_4$ in an ammonia aqueous solution. The samples were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), $N_2$-sorption, and UV-vis diffuse reflectance spectra (UV-vis DRS) techniques. The absorption edge of nitrogen-doped $TiO_2$ shifted into the visible wavelength region. The photoelectrochemical (PEC) performances were investigated for the $TiO_2$ mesoporous electrodes doped with different nitrogen concentrations. The $TiO_2$:N electrodes exhibited much higher PEC responses compared to the pure $TiO_2$ electrode because of the significantly enhanced visible-photoresponsibility of the $TiO_2$:N electrodes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.582-587
• /
• 2023

The effects of the annealing temperature on the structural, morphological, and luminescent properties of SrWO₄:Sm³⁺ thin films grown on quartz substrates by radio-frequency magnetron sputtering were investigated. The thin films were annealed at various annealing temperatures for 20 min in a rapid thermal annealer after growing the thin films. The experimental results showed that the annealing temperature has a significant effect on the properties of the SrWO₄:Sm³⁺ thin films. The crystal structure of the as-grown SrWO₄:Sm³⁺ thin films was transformed from amorphous to crystalline after annealing at 800℃. The preferred orientation along (112) plane and a significant increase in average grain size by 820 nm were observed with increasing the annealing temperature. The average optical transmittance in the wavelength range of 500~1,100 nm was decreased from 72.0% at 800℃ to 44.2% at an annealing temperature of 1,000℃, where the highest value in the photoluminescence intensity was obtained. In addition to the red-shift of absorption edge, a higher annealing temperature caused the optical band gap energy of the SrWO₄:Sm³⁺ thin films to fall rapidly. These results suggest that the structural, morphological, and luminescent properties of SrWO₄:Sm³⁺ thin films can be controlled by varying annealing temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.437-441
• /
• 2006

The red emitting OLEDs using $Alq_3$:Rubrene-GDI4234 phosphors have been fabricated and characterized . In the device fabrication, 2- TNATA [4,4',4' - tris (2- naphthylphenyl - phenylamino ) - tripheny lamine] as the hole injection material and NPB [N,N'-bis (1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as the hole transport material were deposited on the ITO(indium tin oxide)/glass substrate by vacuum evaporation. And then, red color emissive layer was deposited using $Alq_3$ as the host material and Rubrene(5,6,11,12-tetraphenylnaphthacene)-GDI4234 as the dopants. finally, small molecule OLEDs with structure of ITO/2-TNATA/NPB/$Alq_3$:Rubrene-GDI4234/$Alq_3$/LiF/Al were obtained by in-situ deposition of $Alq_3$, LiF and Al as the electron transport material, electron injection material and cathode, respectively. Red OLEDs fabricated in our experiments showed the color coordinate of CIE(0.65, 0.35) and the maximum power efficiency of 2.1 lm/W at 7 V with the peak emission wavelength of 632 nm.