• ETRI Journal
• /
• v.31 no.6
• /
• pp.741-748
• /
• 2009

We present an analysis of microstrip coupled lines (MCLs) used to improve the stability of a 60 GHz narrowband amplifier. The circuit has a 4-stage structure implementing MCLs instead of metal-insulator-metal (MIM) capacitors for the unconditional stability of the amplifier and yield enhancement. The stability parameter, U, is used to compare the stability of MCLs with that of MIM capacitors. Experimental results show that MCLs are more stable than MIM capacitors with the same capacitances as MCLs because the parasitic parallel resistances of MCLs are lower than those of MIM capacitors. Moreover, the bandwidth of an amplifier using MCLs is narrower than one using MIM capacitors because the parasitic series inductances of MCLs are higher than those of MIM capacitors.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.549-556
• /
• 2002

Geotextile tubes hydraulically or mechanically filled with dredged materials have been applied in hydraulic and coastal engineering in recent years(shore protection structure, detached breakwater, groins and jetty). It can also be used to isolate contaminated material from harbor, detention basin dredging, and to use this unit as dikes for reclamation work. Recently, new preliminary design criteria supported by model and prototype tests, and some stability analysis calculations have been studied. The stability analysis of geotextile tube is composed geotechnical and hydrodynamic analysis. The stability check points are sliding failure, overturning, bearing capacity failure against the wave attack. In this paper presented the construction procedure and in-situ measurement(properties of filling material, effective height variation, stress variation at geotextile tube bottom) of geotextile tube at Young-Jin Bay and stability analysis by theoretical method and hydraulic model tests

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.943-946
• /
• 1993

This paper presents design criteria of an overlapping decentralized controller by investigating the controllability and closed loop stability of the expanded system. To determine the criteria we classify the overlapping decentralized controller into an overlapping expanded controller and a contractible controller. It is shown that conditions of system expansion to design these controllers are differently used. The overlapping expanded controller needs the aggregation conditions due to the importance of a structure of the expanded system. The contractible controller which intends to use in the original space needs the restriction because of stability of the original system.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.720-723
• /
• 1999

For that the attitude control performance test of the satellite, dynamic analysis of satellite structure performed in reference with KOREASAT, and the equation of motion of rigid bodies was derivated. For attitude stability, Lyapunov's stability theorem and state space expression were applied to dynamic equation of satellite. To prove efficiency of our method, simulations are performed and result are shown.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.420-420
• /
• 2000

In this paper, we propose an adaptive controller using RBFN(radial basis function network) for robot manipulators The structure of the proposed controller consists of a RBFN and VSC-1 ike control. RBFN is used in order to approximate かon system, and VSC-like control to guarantee robustness On the basis of the Lyapunov stability theorem, we guarantee the stability for the total system. And the learning law of RBFN is established by the Lyapunov method, Finally, we apply the proposed controller to tracking control for a 2 link SCARA type robot manipulator.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.67-74
• /
• 1999

When high speed train meets sidewind, folwfields around the train is very complex. In this case, the force by sidewind has a bad effect on stability of train. We can observe that the flow separates, reattaches, and forms all unsteady vortex in the wake region behind tile structure. Such folwfield can be analyzed by $\kappa$-$\omega$ SST model, and we investigate the effect for various section shape of high speed train. So we acquire the result that as tile corner of train section is rounder, stability of train is better.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.2
• /
• pp.72-76
• /
• 2003

This paper presents the design concept and operation results of float-off for FSO (340,000 DWT Class, ELF AMENAM KPONO Project) built on the ground, without dry dock facilities. It was the first attempt to build FSO, completely, on the ground and launch it using DBU (Double Barge Unit, which was connected by rigid frame structure.) The major characteristics of FSO, which are similar to general VLCC type hull, including topside structure, weigh 51,000 metric ton. In order to have sufficient stability during the deck immersion of DBU, while passing through a minimum water plane area zone, proper trim control was completed with LMC (Load Master Computer). The major features of the monitoring system include calculation for transverse bending moment, shear force, local strength check of each connector, based on component stress, and deformation check during the load-out and float-off. Another major concern during the operation was to avoid damages at the bottom and sides of FSO, due to motion & movement after free-floating; therefore, adequate clearances between DBU and FSO were to be provided, and guide posts were installed to prevent side damage of the DBU casings. This paper also presents various measures that indecate the connector bending moment, damage stability analysis, and mooring of DBU during float off.

• Journal of the Korean Institute of Rural Architecture
• /
• v.2 no.1
• /
• pp.101-112
• /
• 2000

Green environment is most important factor to human being taking a side view of psychological aspect. But, as the civilization progresses rapidly, the green environment decreases. At present, various environmentally friendly methods are developed to prevent the ill effect of the concretes. n this study, Ecostone retaining wall method, which is a kind of environmentally friendly block, are used for verifying the application to the slope stability and protection of rural hosing. In case of rural hosing and structure, the height of the slope is not high and additional loading doesn't act on the slope except the gravity loading of housing and structure. From the result of the stability analysis of Ecostone, 3m to 7m Ecostone retaining wall can have an equivalence capacity comparing with the concrete retaining wall. Therefore, Ecostone method can apply to retaining wall with the structural safety and environmentally friendly aspect using the plants and vegetation.

• Structural Engineering and Mechanics
• /
• v.65 no.1
• /
• pp.121-128
• /
• 2018

Three structure-dependent integration methods with no numerical dissipation have been successfully developed for time integration. Although these three integration methods generally have the same numerical properties, such as unconditional stability, second-order accuracy, explicit formulation, no overshoot and no numerical damping, there still exist some different numerical properties. It is found that TLM can only have unconditional stability for linear elastic and stiffness softening systems for zero viscous damping while for nonzero viscous damping it only has unconditional stability for linear elastic systems. Whereas, both CEM and CRM can have unconditional stability for linear elastic and stiffness softening systems for both zero and nonzero viscous damping. However, the most significantly different property among the three integration methods is a weak instability. In fact, both CRM and TLM have a weak instability, which will lead to an adverse overshoot or even a numerical instability in the high frequency responses to nonzero initial conditions. Whereas, CEM possesses no such an adverse weak instability. As a result, the performance of CEM is much better than for CRM and TLM. Notice that a weak instability property of CRM and TLM might severely limit its practical applications.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.34-39
• /
• 2017

Semiconductor is one of the most internationally competitive areas among domestic industries, the major concern of which is the stability of the wafer manufacturing processes. The first process for the manufacturing of the semiconductor wafers is the ingot growing. The vibrations are supposed to be the most important factors for the ingot quality. In order to maintain the ingot quality, the growers have the automatic shut-down equipments which are activated by vibrations, and are sensitive enough to react to the earthquakes generated in Japan. In this study, the structure of an ingot grower was analyzed through experiments and computer simulations, and further the effects of design alterations to suppress the vibrations have been investigated. The final result shows that the vibrations can be reduced substantially to improve the stability of the structure.