• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.87-90
• /
• 2001

This paper presents a design of new type biped robot and dynamic walking simulation for this system. The robot is distinguished from other one by which has a parallel mechanism type trunk and lead-screw type actuators to drive the joints of the trunk, knee and ankle. The basic consideration on the design is that it is able to accommodate itself to human's daily environments without any other modification of around and also to operate its upper limbs more smoothly with a spine functional trunk. It is designed according to a human with about 130 cm height and about 30 kg weight. And it also is able to dynamically walk on an even ground. It has constructed with total 14 DOFs which have two legs, a hip, and a trunk. The joints of each leg and trunk are adopted with a parallel structure which has good kinematic characteristics and take light weight. To test of the capacity of joint actuators and to analysis of the dynamic properties of the biped robot, optimized trunk trajectory is determined by means of an approximated FFT method based on ZMP criteria, and dynamic simulation is performed using DADS with a 1.1 time/step velocity on the even ground during four steps.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.3 s.234
• /
• pp.369-386
• /
• 2005

Various aspects of structural optimization techniques under transient loads are extensively reviewed. The main themes of the paper are treatment of time dependent constraints, calculation of design sensitivity, and approximation. Each subject is reviewed with the corresponding papers that have been published since 1970s. The treatment of time dependent constraints in both the direct method and the transformation method is discussed. Two ways of calculating design sensitivity of a structure under transient loads are discussed - direct differentiation method and adjoint variable method. The approximation concept mainly focuses on re- sponse surface method in crashworthiness and local approximation with the intermediate variable Especially, as an approximated optimization technique, Equivalent Static Load method which takes advantage of the well-established static response optimization technique is introduced. And as an application area of dynamic response optimization technique, the structural optimization in flexible multibody dynamic systems is re- viewed in the viewpoint of the above three themes

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.236-240
• /
• 2013

Due to difficulty of considering dynamic load in side of a computer resource and computing time, it is common that external load is assumed as ideal static load. However, structural analysis under static load cannot guarantee the safety of structural design. Recently, the systematic method to construct equivalent static load from the given dynamic load has been proposed. Previous study has calculated equivalent static load through the optimization procedure under displacement constraints. And previously reported works to distribute equivalent static load were based on ad hoc methods. However, it is appropriate to take into account the stress constraint for the safety design. Moreover, the improper selection of loading position may results in unreliable structural design. The present study proposes the methodology to optimize an equivalent static which distributed on the primary DOFs, DOFs of the constraint elements, DOF of an external load as positions. In conclusion, the reliability of proposed method is demonstrated through a global optimization.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.270-277
• /
• 2012

This paper presents a new DAC design strategy to achieve a wideband dynamic linearity by increasing the bandwidth of the output impedance. In order to reduce the dominant parasitic capacitance of the conventional matrix structure, all the cells associated with a unit current source and its control are stacked in a single column very closely (stacked unit cell structure). To further reduce the parasitic capacitance, the size of the unit current source is considerably reduced at the sacrifice of matching yield. The degraded matching of the current sources is compensated for by a self-calibration. A prototype 6-bit 3.3-GS/s current-steering full binary DAC was fabricated in a 1P9M 90 nm CMOS process. The DAC shows an SFDR of 36.4 dB at 3.3 GS/s Nyquist input signal. The active area of the DAC occupies only $0.0546mm^2$ (0.21 mm ${\times}$ 0.26 mm).

• Journal of Welding and Joining
• /
• v.28 no.5
• /
• pp.58-63
• /
• 2010

The purpose of this study is to develop improved boom structures with reliable fatigue strength of weldment and lower production cost. For that purpose, multibody dynamic analysis was performed to evaluate forces acting on arm & boom cylinders and joints of boom structure during operation of an excavator for three working postures, then stress analysis was made to investigate stress distribution around diaphragms at the bottom plate of boom structures which was known to be susceptible to fatigue failures of welded joints, and finally boom structure with optimum arrangement of diaphragms was proposed. This work basically consists of the following two parts: part 1 focuses on multibody dynamic analysis of excavators during operation and part 2 includes evaluations of fatigue strength of welded joints for modified boom structures.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.1
• /
• pp.137-142
• /
• 2005

Biomedical signals such as ECG, EMG, and EEG are extremely important in the diagnosis of patients. It is difficult to filter noise from these signals, and errors resulting from filtering can distort a biomedical signal. Existing systems have shown poor performance when complicated noise appears. Adaptive filtering is selected to contend with these defects. Existing adaptive filters can adjust the filter coefficient with the given filter order, but they can produce an unsuitable order in different environments. In order to solve this problem, an optimal adaptive filter with a dynamic structure was designed. Positive experimental results were obtained.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1507-1516
• /
• 2001

An analytical method is presented for evaluation of the steady state periodic behavior of nonlinear structural systems. This method is based on the substructure synthesis formulation and a harmonic balance procedure, which is applied to the analysis of nonlinear responses. A complex nonlinear system is divided into substructures, of which equations are approximately transformed to modal coordinates including nonlinear term under the reasonable procedure. Then, the equations are synthesized into the overall system and the nonlinear solution for the system is obtained. Based on the harmonic balance method, the proposed procedure reduces the size of large degrees-of-freedom problem in the solving nonlinear equations. Feasibility and advantages of the proposed method are illustrated using the study of the nonlinear rotating machine system as a large mechanical structure system. Results obtained are reported to be an efficient approach with respect to nonlinear response prediction when compared with other conventional methods.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.573-581
• /
• 1999

액체 금속로(LMIR) 핵연료교환장치의 기본설계를 위해서는 여러 분야(예를 들면, 기구학, 동역 학, 재료역학 등)의 해석을 동시에 수행해야 한다. 그러나 이와 같은 해석들은 각각 별개로 연속적으로 수행되는 것이 아니라, 상호 유기적인 연관을 갖고 수행되어야 한다. 이와 같은 해석에 적합한 기법이 MDO 기법이다. 본 논문에서는 MDO기법에 의한 핵연료교환장치 구조해석의 한 단계로 핵연료교환장치의 기구 동역 학 해석을 수행하여 핵연료 교환장치 작동에 대한 기구운동학적 특성 및 동역학적 특성을 분석하였다. 분석결과 해석대상 핵연료교환장치는 예상한대로 원활하게 작동됨이 확인되었다. 아울러 이 분석 결과를 토대로 핵연료교환장치의 정적 휨 변형을 구하기 위한 재료역학해석에서 요구되는 정적구조를 결정하였다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.4
• /
• pp.452-459
• /
• 2019

In order to design and manufacture structures such as a guided missile, assembly process with fastener is an essential method of fabrication. In this study, the dynamic characteristics of a cylindrical structure with bolted joints were studied using experimental methods. The change of the natural frequency of the structure with the change of the fastening method and the tightening torque were measured by the test and the finite element analysis was performed using the stiffness model of the fastening part according to the fastening method and compared with the test results.

• Journal of Biomedical Engineering Research
• /
• v.19 no.5
• /
• pp.519-530
• /
• 1998

In this paper, the basic study on the design of the flexible keel of the energy-storage prosthetic foot was performed in order to Improve the walking performance and Increase the activities of the below knee amputees. Based on the analysis of the anthropometric data and the normal gait on two dimensional sagittal plane available In the literature, we presented a model of the basic structure of the flexible keel of the prosthetic foot. The model of the basic structure was composed of the simple beams, and linear rotational spring and damper. Laminated carbon fiber-reinforced composites were selected as the material of the basic structure model of the flexible keel In order to apply the high strength and light weight materials to the basic structure of the flexible keel of the prosthetic foot. The recoverable strain energy In response to the change of beam shape was calculated bur the finite element analysis and it was suggested that the change of beam shape could be the design variable in flexible keel design. The simulation process was systematically designed by using orthogonal array table in order to design the flexible keel structure which could store the more recoverable strain energy. finite element analysis was carried but according to the design of simulations by using the finite element program ABAQUS and the flexible keel structure of the energy-storage prosthetic foot was obtained from the analysis of variance(ANOVA). The dynamic simulation model of the prosthetic walking using the flexible keel structure was made and the dynamic analysis was carried but during one walk cycle. Based on the above results, an effective design process was presented for the development of the prosthetic fool system.