• 한국강구조학회 논문집
• /
• 제16권2호통권69호
• /
• pp.275-284
• /
• 2004

기둥-보 약축 접합 디테일 개발을 위해서 접합부의 거동을 파악하는 것이 선행되어야한다. 약축 접합부의 형식에 따른 강축 접합부의 거동을 파악하기위하여 기존 브라켓타입 용접접합부의 각 요소들 즉 패널존, 수평스티프너의 유무 및 위치를 변수로 고려하였다. 본 연구에서는 접합부에 수평스티프너가 있는 경우는 접합부를 수직스티프너로 보강한 단순보로 치환하여 접합부의 내력을 산정하였으며, 수평스티프너가 없는 경우는 기둥플랜지의 국부휨강도, 기둥 웨브의 국부인장강도, 기둥 웨브의 크립플링강도 및 기둥웨브의 최대 좌굴강도를 고려한 내력 평가식을 사용하였고 이론해석결과와 실험결과를 비교 분석하였다.

• Coupled systems mechanics
• /
• 제3권2호
• /
• pp.195-211
• /
• 2014

When strong seismic forces act on reinforced concrete structures, their beam-column connections are very susceptible to damage during the earthquake event. The aim of this numerical work is to evaluate the influence of the internal steel reinforcement array on the nonlinear response of a RC beam-column connection when it is subjected to strong cyclic loading -as a seismic load. For this, two specimens (extracted from an experimental test of 12 RC beam-column connections reported in literature) were modeled in the Finite Element code FEAP considering different stirrup's arrays. In order to evaluate the nonlinear response of the RC beam-column connection, the 2D model takes into account the nonlinear thermodynamic behavior of each component: for concrete, a damage model is used; for steel reinforcement, it is adopted a classical plasticity model; in the case of the steel-concrete bonding, this one is considered perfect without degradation. At the end, we show a comparison between the experimental test's responses and the numerical results, which includes the distribution of shear stresses and damage inside the concrete core of the beam-column connection; in the other hand, the effects on the connection of a low and high state of confinement are analyzed for all cases.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2016년도 춘계학술발표대회
• /
• pp.897-899
• /
• 2016

In recent years, BLE technology has received extensive attention and has been applied to all aspects of life. The existing BLE device has two methods, one is the connection method, and the other is a non-connection method. The representative profile of the connection method is the proximity file. The most typical example of Non-connection method BLE device is a beacon. However, they are both independent and have their own shortcomings. Connection method device can provide service for only one user, others can't use. Security performance of Non-connection method BLE device is poor and the device can't be controlled by the user. In this paper, a combination-mode BLE device profile design scheme is presented, which combines with the previous two methods, and solves the defaults. And We define a dual purpose advertising package that can be used in a normal environment as well as in a disaster environment. Finally, a unidirectional Control idea is proposed. Through performance evaluation, we found that the device has strong stability and low power consumption.

• 한국멀티미디어학회논문지
• /
• 제21권6호
• /
• pp.667-677
• /
• 2018

Since sensor networks consist of sensor nodes with limited energy resources, so efficient energy use of sensor nodes is very important in the design of sensor networks. Sensor nodes consume a lot of energy for data transmission. Clustering technique is used to efficiently use energy in data transmission. Recently, mobile sink techniques have been proposed to reduce the energy load concentrated on the cluster header near a sink node. The CMS(Cluster-based Mobile sink) technique minimizes the generation of control messages by creating a data transmission path while creating clusters, and supports the inter-cluster one-hop transmission. But, there is a case where there is no connectivity between neighbor clusters, it causes a problem of having a long hop data transmission path regardless of local distance. In this paper, we propose a SCBC(Strong connection balancing cluster) to support the path of the minimum number of hops. The proposed scheme minimizes the number of hops in the data transmission path and supports efficient use of energy in the cluster header. This also minimizes a number of hops in data transmission paths even when the sink moves and establishes a new path, and it supports the effect of extending the life cycle of the entire sensor network.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1994년도 춘계학술대회
• /
• pp.111-114
• /
• 1994

Three component velocity measurements with a refractive index-matching technique was used to investigate the flow characteristics in the atrio-pulmomnary (AP) Fontan connection under the steady flow condition. A strong swirl was observed in the extra-cardiac conduit and the main pulmonary artery (MPA). Maximum velocity magnitude in the MPA was about 0.8 m/s near the posterior wall at 6 liter/min. Swirling motion of the flow as well as geometric abnormalities of the connection are important factors in energy loss across Fontan connections.

• 대한수학회보
• /
• 제42권4호
• /
• pp.691-701
• /
• 2005

We study the strong stability for linear differential systems in connection with too-similarity, and investigate the asymptotic equivalence between linear differential systems.

• 콘크리트학회논문집
• /
• 제26권4호
• /
• pp.545-553
• /
• 2014

이 연구는 PC 보-기둥 접합부의 일반적인 거동의 접합 상세에 따른 통합적 평가 방안을 제안하였다. 이 연구는 접합부의 파괴 패턴과 이에 연관된 접합부 상세의 특징을 정량적으로 표현하기 위해 접합부와 각 요소들이 보유한 변형기여분을 사용할 것을 제안하였다. 이에 따라 PC 접합부는 '일체식 접합부'와 '연결식 접합부'로 크게 분류되었다. 접합부의 분류를 위한 기준 사항의 제안 및 검증을 위해 네 개의 보-기둥 실험체의 실험을 수행하였다. 실험은 일반적인 보-기둥 접합부의 실험 방법과 같은 방법으로 진행되었다. 가력은 접합부 상부 기둥의 끝단에서 수행되었으며, 보 양단은 힌지로 고정되었다. 변형기여분의 평가를 위해 총 34개의 LVDT가 주요 변형이 발생할 것으로 예상되는 곳에 설치되었다. 실험 결과 세 개의 실험체에서 나타난 각 요소들의 변형기여분은 수치적으로 다른 특성을 가지고 있는 것을 확인할 수 있었다. 실험 결과를 기반으로 접합부의 변형 정도와 다른 요소들의 변형 정도에 의거하여, 접합부의 변형이 적고 보의 휨 변형이 크게 나타나는 강한 접합부와 접합부의 변형이 용인되는 연성 접합부로 일체식 접합부를 분류할 수 있었다.

• 한국강구조학회 논문집
• /
• 제16권1호통권68호
• /
• pp.169-180
• /
• 2004

강구조 기둥-보 접합부에 대한 연구는 그동안 국내외에서 오랜 기간 연구가 진행되어 내진성능 및 집합부의 강도를 개선시킬 수 있는 많은 접합 디테일이 개발되어 사용 중에 있으나, 현재 국내에서는 시공성을 고려하여 기존의 브라켓 형식의 접합부를 선호하고 있다. 본 연구에서는 약축 접합부의 연성적인 거동을 확보하면서 시공이 편리한 기둥-보 접합부를 실험과 이론해석을 통해 개발함으로써 철골구조시스템이 중저층 건물에도 사용할 수 있도록 하는데 그 목적이 있다. 또한 약축에 대한 기둥-보 접합부의 구조설계 및 시공에 필요한 기초 자료를 제시하고자 한다.

• Steel and Composite Structures
• /
• 제26권1호
• /
• pp.31-44
• /
• 2018

This paper reports a novel steel beam-to-column connection suitable for use in the weak axis of I-section column. Monotonic and cyclic loading experimental investigations and numerical analysis of the proposed weak-axis connection were conducted, and the calculation procedure of the beam-column relative rotation angle and plastic rotation angle was developed and described in details. A comparative analysis of mechanical property and steel consumption were employed for the proposed I-section column weak-axis connection and box-section column bending connection. The result showed that no signs of fracturing were observed and the plastic hinge formed reliably in the beam section away from the skin plate under the beam end monotonic loading, and the plastic hinge formed much closer to the skin plate under the beam end cyclic loading. The fracture of welds between diaphragm and skin plate would cause an unstable hysteretic response under the column top horizontal cyclic loading. The proposed weak-axis connection system could not only simplify the design calculation progress when I-section column is adopted in frame structural design but also effectively satisfy the requirements of 'strong joint and weak member', as well as lower steel consumption.

• 대한건축학회논문집:구조계
• /
• 제34권12호
• /
• pp.11-20
• /
• 2018

The purpose of this study is to investigate the seismic performance of exposed column-base plate strong-axis connections for small-sized steel buildings. Even though the seismic design for small-sized buildings became mandatory since Dec.2017, the arbitrary connection details in steel structure have been applied at the construction site, which is considered to be very insufficient to secure structural safety and stability considering the increased seismic risk. Therefore, a series of experimental test programs had been carried out to develop enhanced connection details in order to ensue the adequate seismic safety of small buildings. The hysteretic behavior of the exposed column-base plate connections commonly used in Korea seem to be very pure poor due to the "Rocking" phenomena between anchor plate and concrete by the residual plastic deformation of anchor bolts. A series of hysteretic tests were conducted to find the solution to overcome the "Rocking" phenomena of the exposed column-base plate connections, finally the stable seismic behavior was obtained by uisng at least 8 anchor bolts with good bonding strength to the protptype specimen.