• Journal of Korea Foundry Society
• /
• v.21 no.4
• /
• pp.232-238
• /
• 2001

Experimental study on the twin roll strip casting of BCuP-5(Cu-15wt%Ag-wt5%P) alloy was carried out using laboratory scale horizontal type twin roll caster. In this study, among the various operating parameters, such as tundish angle, contact angle, pouring temperature, roll speed, presetting gap of the rolls and kinds of roll and tundish materials, effect of pouring temperature for strip casting of BCuP-5 alloy which has long freezing range of about $170^{\circ}C$ was mainly investigated. BCuP-5 alloy strip was successfully produced when pouring molten metal at lower temperature than its liquidus temperature. Microstructure of the cast strip consists of primary Cu and eutectic. Especially the size of primary Cu phase increased with decreasing of pouring temperature.

• Journal of Welding and Joining
• /
• v.22 no.3
• /
• pp.62-68
• /
• 2004

The strip Au bumps are bonded using longitudinal ultrasonic far the electronic package. Au bumps on the chip and substrate are aligned in a crossed shape, and the ultrasonic is imposed on the chip to form the solid-state bond between the Au bumps. Deformed bump shapes are calculated using the finite element method, and the bond strength is measured experimentally. The crossed strip Au bumps are deformed similar to the saddle, which provides larger contact surface area and higher friction force. Compared with the previous bonding method between the Au bump and planar pad, higher bond strength is obtained using the crossed strip bumps.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.116-120
• /
• 2020

In this paper, we developed an electrochemical glucose sensor strip using a paper substrate. The paper glucose sensor strip is eco-friendly because it uses paper as a substrate, and it has the advantage that it can be manufactured only with four printing, drying and cutting processes. The paper glucose sensor is significantly simplified by the production process than the conventional glucose sensors because the production of only four printing on the paper substrate. In this paper, eco-friendly tracing paper was used to develop a paper glucose sensor strip, and screen-printing technology was used to form a carbon/silver electrode, insulating layer and glucose oxidase(GOD) layer. The developed paper glucose sensor strip has a flat structure with a size of 30 × 4.6 ㎟, and blood injection is a type of direct contact with the exposed enzyme layer above the strip. In this paper, the performance of paper glucose sensor strips was evaluated by analyzing the cyclic voltammetry(CV) and chronoamperometry(CA) characteristics.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.11
• /
• pp.1279-1287
• /
• 2011

Weather strip is a functional component of a car body and doors for leaking protection, isolating outside noise and vibration reduction. Insert metal inserted to the weather strip plays a key role to keep the shape of the weather strip and increase its strength. Insert metal is mainly produced by a press process, which has low productivity and 40% material loss due to the scraps. To solve the problems, a high-speed rolling process for manufacturing the insert metal of weather strip is being attempted. In this study, the insert metal is manufactured by a high-speed rolling process, and its process variables: reduction, relative velocity of rollers and the number of passes, are optimized by using the FEA and the actual tests. The prototype was manufactured by the optimal process.

• Journal of Korea Foundry Society
• /
• v.22 no.4
• /
• pp.174-183
• /
• 2002

Twin-roll process is a relatively new continuous casting process which can produce high-quality strip products directly, and solidification rate can reach $10^3$ to $10^4$ K/s, leading to fine and uniform microstructures with enhanced mechanical properties. The strip casting condition for producing fine Al-Sn alloy strip was obtained experimentally, and defects appearing on the strip was examined. Crack formation and surface quality of the strip was found to depend mainly on process parameters such as melt temperature, roller gap and rolling speed. Sn structure of network type was observed in Al-20Sn and Al-40Sn alloy strips, and cell spacing of Al-40Sn alloy was smaller than that of Al-20Sn. Banding strength of the heat treated specimens increased with increasing of soaking time and temperature, and bonding strength of Al-20Sn alloy was more superior than that of Al-40Sn alloy. However wear resistance of Al-40Sn alloy contained large amount of soft Sn which possess good anti-friction characteristics was superior than that of Al-20Sn alloy.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.80-85
• /
• 2002

The progressive die for U-bending production part is a very specific division. This study reveals the Sheet metal forming process with multi-forming die by Center Carrier type feeding system. Through the FEM simulation by DEFORM it was accepted to u-bending process as the first performance to design in strip process layout design. The next process of die development was studied according to sequence of die development.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.4
• /
• pp.101-111
• /
• 1998

This study presents test results of RC beams strengthened by carbon fiber sheet(CFS), carbon fiber reinforced plastics(CFRP) or glass fiber reinforced plastics(GFRP) for increasing shear resistance. Nineteen specimens were tested, and the test was performed with different parameters including the type of strengthening materials(CFS, GFRP, CFRP), shear-strengthening methods(wing type, jacket type, strip type), strip-spacing, strengthening direction of FRP. The test results show that shear-damaged RC beams strengthened by FRP(CFS, GFRP, CFRP) have more improved the shear capacity. The mathematical model based on plastic theory was also developed to predict shear strength of shear-damaged RC beams strengthened by FRP. The predictions using the mathematical model. are agreed with the observations from the observed shear strengths for 19 test beams.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2011.10a
• /
• pp.93-93
• /
• 2011

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.594-606
• /
• 1999

The electromagnetic scattering characteristics by a periodic strip grating on a grounded dielectric slab for TE polarization case is examined from the viewpoints of both the reflection grating and the leaky wave antenna problems. Numerical results for two kinds of Bragg blazing (resonance type and non-resonance type) phenomena are given and some discussions on the properties such as complex propagation constants, scattering characteristics, and distributions of strip current density are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.779-782
• /
• 1990

Recently batch type cold rolling processes have been replaced by continuous annealing type processes for cold rolled sheets of mild steel and high strength steel in order to obtain higher productivity, labor saving. In the continuous annealing line, it is very important to maintain the target steel strip temperature at the exit side of each furnace. The automation system of continuous annealing line is based on a hierachical composition. This paper shows how to preset the set value of furnace temperature control for the heating section in a continuous annealing line. Saying in other words, this paper presents the development of an adaptive control approach to control the exit strip temperature in the continuous annealing line. There are three parts in this approach; one is a process modelling and another is recursive parameter estimation and the other is a design of temperature controller.