• Journal of the Korean Wood Science and Technology
• /
• v.14 no.2
• /
• pp.3-12
• /
• 1986

The aim of this study is to determine the flexural properties(Modulus of Rupture, Modulus of Elasticity) of Platanus occidentalis L. laminated beams fabricated with 1, 3, 5, 8, 15 lamination and Tension, Compression lamination. The results were as follows: 1. MOR increased with increasing number of lamination in 3, 5, 8, 15-beam and Tension lamination beam. MOR of Compression lamination beam was lower than that of 3-beam, MOR of vertical beam not having Tension or compression lamination was lower than that of horizontal beam, but MOR of vertical beam with tension or compression lamination was same or slightly higher than that of horizontal beam. 2. The allowable working stress showed the same tendency. This stress increased with increasing number of lamination. This value of Tension lamination beam was higher than that of compression lamination beam. 3. MOE of all laminated beams was higher than that of solid beam and Tension lamination beam was higher than that of 3-beam. MOE of Tension lamination beam was higher than that of Compression lamination beam. MOE of all vertical beam was higher than that of horizontal beam except for T-2, T-5, C-3. 4. Most beam failures appeared to begin in tension. These tension failures were classified into Splintering tension, Cross-grained tension, Simple tension, Brittle tension. All test beam failures could be classified into three categories. 1) Tension failure 2) Compression failure 3) Horizontal shear failure.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.76-83
• /
• 2001

This study was carried out to clarify the mechanical behaviour of the earlywood and the latewood to the compressive load applied parallel to the grain. The results from the analysis of Japanese cedar wood (Cryptomeria japonica) were used to introduce a concept on stress-strain behaviour of the earlywood and the latewood. There was a significant differences in the mechanical behaviour of the earlyWood and the latewood. In the earlywood, the rate of cell wall upon annual ring was almost similar and the strain increased linearly with the stress increased. However, the rate of cell wall upon annual ring varied in the latewood and the strain of that increased curve-linearly with the stress increased. The longitudinal compression modulus of elasticity (MOE) variation by loading speed on latewood specimens and earlywood specimens shows no significant difference. The modulus of rupture (MOR) and MOE of latewood were about 4 times higher than those of earlywood.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.12
• /
• pp.2565-2573
• /
• 2002

A basic research was performed to ensure the usefulness of Small Punch-creep(SP-creep) test for residual life evaluation of heat resistant components effectively. This paper presents analytical results of initial stress and strain distributions in SP specimen caused by constant loading for SP-creep test and its experimental correlations with uniaxial creep(Ten-creep) test on 9Cr1MoVNb steel. It was shown that the initial maximum equivalent stress, ${\sigma}_{eq{\cdot}max}$ from FE analysis was correlated with steady-state equivalent creep strain rate, ${\epsilon}_{qf-ss'}$ rupture time, $t_r$, activation energy, Q and Larson-Miller Parameter, LMP during SP-creep deformation. The simple correlation laws, ${\sigma}_{sp}-{\sigma}_{TEN}$, $P_{sp}-{\sigma}_{TEN}\; and\; Q_{sp}-Q_{TEN}$ adopted to established a quantitative correlation between SP-creep and Ten-creep test data. Especially, the activation energy obtained from SP-creep test is linearly related to that from Ten-creep test at $650^{\circ}C$ as follows : $Q_{SP-P}\;{\risingdotseq}\;1.37 \;Q_{TEN},\; Q_{SP-{\sigma}}{\risingdotseq}1.53\; Q_{TEN}$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.129-138
• /
• 2010

Technical ceramics, due to their unique physical properties, are excellent candidate materials for engineering applications involving extreme thermal and chemical environments. When ceramics are rapidly cooled, they receive thermal shock. The thermal shock parameter is defined as the critical temperature difference. The critical temperature difference for ceramic parts is influenced by its size, the convective heat transfer coefficient, etc. The thermal shock for a component is analyzed by using the transient thermal stress. If the transient thermal stress exceeds the modulus of rupture (MOR), cracking by thermal shock is initiated. The critical temperature difference for water is less than the critical temperature difference for air. The three-way catalyst substrate used in this study has an adequate performance against thermal shock because its radial and axial temperature differences existed below the critical temperature differences.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1988.06c
• /
• pp.3-67
• /
• 1988

Model studies on the response of homgeneous earth embankment dams subjected to strike-slip fault movement have been penomed via centrifuge and finite element analysis. The centrifuge model tests have shown that crack development in earth embankment experiences two major patters: shear failure deep inside the embankment and tension failure near the surface. The shear rupture zone develops from the base level and propagates upward continuously in the transverse direction but allows no open leakage chnnel. The open tensile cracks develop near the surface of the embankment, but they disappear deep in the embankment. The functional relationship has been developed based on the results of the centrifuge model tests incorporating tile variables of amount of fault movement, embankment geometry, and crack propagation extent in earth des. This set of information can be used as a guide line to evaluate a "transient" safety of the duaged embankment subjected to strike-slip fault movement. The finite element analysis has supplemented the additional expluations on crack development behavior identified from the results of the centrifuge model tests. The bounding surface time-independent plasticity soil model was employed in the numerical analysis. Due to the assumption of continuum in the current version of the 3-D FEM code, the prediction of the soil structure response beyond the failure condition was not quantitatively accurate. However, the fundamental mechanism of crack development was qualitatively evaluated based on the stress analysis for the deformed soil elements of the damaged earth embankment. The tensile failure zone is identified when the minor principal stress of the deformed soil elements less than zero. The shear failure zone is identified when the stress state of the deformed soil elements is at the point where the critical state line intersects the bounding surface.g surface.

• Economic and Environmental Geology
• /
• v.55 no.2
• /
• pp.183-195
• /
• 2022

Hydrothermal gold deposits are evidence of intensive fluid flow through fault zones, and the resultant vein structures and textures reflect the fluid redistribution mechanism. This review introduces the suction pump and fault valve models as fluid circulation mechanisms causing hydrothermal gold deposits in the frameworks of the concepts of fault mechanics. The suction pump and fault valve models describe faulting-driven heterogeneous fluid flow and related vein formation mechanisms, accompanied by the cycles of (1) stress accumulation and fluid pressure build-up and (2) seismic rupture and stress/fluid pressure release. The models are available under different geological environments (stress conditions), and the vein structures and textures representing the mechanisms have similarities and differences. The suction pump and fault valve models must help better to interpret the origins of hydrothermal gold deposits in Korea and improve the efficiency of further exploration.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.456-462
• /
• 2015

365 pieces of domestic $38{\times}140{\times}3600mm$ Red pine structural lumber were machine graded conforming to a softwood structural lumber standard (KS F 3020). The allowable bending stresses calculated for each grade were compared with the values currently tabulated in the standard. Four calculation methods for lower $5^{th}$ percentile bending stress were non-parametric estimation with 75% confidence level, 2-parameter and 3-parameter Weibull distribution fit, and bending modulus of rupture (MOR)-modulus of elasticity (MOE) regression based method. Only the data set of Grades E8, E9, and E10 were statistically eligible for the $5^{th}$ percentile calculation. The MOR-MOE regression based method only was able to estimate the lower $5^{th}$ percentile values theoretically for the full range of grades. The results showed that all allowable bending stresses calculated were lower than the design values tabulated in the standard. This implies that the current machine grading system has the pitfall of structural safety. Improvement in current machine grading system could be achieved by introducing the bending strength and stiffness combination grade system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.25-33
• /
• 2020

To investigate the relationship between strain distribution and tensile properties of brittle material, five types of tensile coupon of carbon fiber reinforced polymer (CFRP) modified the tab portion in order to have a strain distribution including S0, SD1, SD2, SV1, SV2 were tested. The ultimate stress and strain of SD2 and SV2 which was intended to have larger strain distribution were smaller than those of SD1 and SV1, that was more clearly shown in the test results of the symmetric coupons (SV series) than the asymmetric coupons (SD series). In addition, the ultimate stress and strain of most coupons with strain distribution in this study were decreased when compared to the control group with uniform strain. These results were analyzed in various ways through 1) the average of the strain values directly measured by the strain gages, 2) the converted strain calculated by dividing the total deformation by the effective length, and 3) the ultimate effective strain derived from both the elastic modulus and the ultimate load. The values measured by strain gage indicates response of the local region precisely, but it does not represent the response from whole section. However, the converted strain and effective strain can supplement disadvantage of gage because they represent the average response of whole section. In particular, the effective strain can provide rupture strain conservatively, which can be utilized in practice, when the value obtained by strain gage was not effective due to gage damage or abnormal gage readings near ultimate load. This value provides a value that can be used even when partial rupture has occurred and is reasonably useful for specimens with strain distribution.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.446-455
• /
• 2015

Based on comparative studies on standards and grading procedures of machine graded lumber in Korea and other countries, this study proposed a procedure of determining the grade classification and design strengths of domestic machine graded lumber. Differences between machine stress rated lumber and E-rated laminations were detailed in order to clarify the need for the procedure improvement. To this improvement the use of average MOE requirement for grading was introduced instead of the fixed minimum MOE requirement which is currently used in the Korean standards. It was found that the fixed minimum MOE requirement method was easier for an inspector to grade but, less efficient as a strength predictor than the average MOE requirement method. The advantage of average MOE requirement method is statistically MOR-MOE regression-based MOR prediction and highly efficient in quality control though it requires a computer-aided operation system in an initial setup. A major weakness of the current Korean grading system was found that different strength characteristics depending on wood species were not reflected on the grade classification and the tabulated allowable design stress. The proposed procedures were developed taking advantages of respective merits of both methods and based on MOR-MOE regression analysis. Through this procedure, the grades of machine stress rated lumber should be revised to become interchangeable with E-rated lamination, which would be beneficial to the cost competitiveness of domestic machine graded lumber and glued laminated timber industry.

• Journal of Korean Neurosurgical Society
• /
• v.47 no.5
• /
• pp.345-351
• /
• 2010

Objective : In this study, the Mindfulness Based Stress Reduction (MBSR) program was applied to patients presenting with depression and anxiety after surgery from spontaneous subarachnoid hemorrhage (SAH) and the effects were assessed. Methods : The subjects were patients admitted for cerebral aneurysm rupture and treated by means of surgery from March to December, 2007. More than 6 months had passed after surgery, without any special lesions showing up on computed tomography (CT), and the Glasgow outcome scale (GOS) was 5 points. Among patients with anxiety and depression symptoms, 11 patients completed the program. The MBSR program was conducted once a week, 2.5 hours each, for 8 weeks. The evaluation criteria were : 1) the Beck Depression Inventory (BDI): it measures the type and level of depression, 2) the State-Trait Anxiety Inventory : the anxiety state of normal adults without mental disorder, and 3) Heart Rate Variability (HRV) : the influence of the autonomous nervous system on the sinoarterial node varies continuously in response to the change of the internal/external environment. Results : The BDI value was decreased from 18.5 ${\pm}$ 10.9 to 9.5 ${\pm}$ 7.1 (p = 0.013) : it was statistically significant, and the depression level of patients was lowered. The state anxiety was decreased from 51.3 ${\pm}$ 13.9 to 42.3 ${\pm}$ 15.2; the trait anxiety was reduced from 50.9 ${\pm}$ 12.3 to 41.3 ${\pm}$ 12.8, and a borderline significant difference was shown (p = 0.091, p = 0.056). In other words, after the treatment, although it was not statistically significant, a decreased tendency in anxiety was shown. In the HRV measurement, standard deviation normal to normal (SDNN), square root of the square root of the mean sum of squared differences between adjacent normal to normal intervals (RMSSD), and total power (TP) showed significant increase, Physical Stress Index (PSI) showed a significant reduction, and thus an improvement in the homeostatic control mechanism of the autonomic nervous system was ween. Conclusion : The MBSR program was applied to the patients showing anxiety and depression reaction after SAH treatment, and a reduction in depression symptoms and physiological reactions were observed. The application of the MBSR program may be considered as a new tool in improving the quality of life for patients after surgery.