• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.771-776
• /
• 2000

Fine grid calculations are reported for the developing turbulent flow in a straight duct and a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=R_c/H_H=3.357$ and a bend angle of 180 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 1999.03a
• /
• pp.153-157
• /
• 1999

Voigt Model assumed for creep was used to obtain the viscoelastic properties of fabrics in thickness direction and the governing equation was derived. The weights were specially designed and calibrated for constant stress applied to fabrics and the 1 ${\mu}{\textrm}{m}$ resolution laser displacement sensor was attached in order to measure the variation of strain. Ten fabric samples were used. The few steps of strain showed according to the internal structure of fabrics. Also correlations the Hand Values from KESF with the spring and damping coefficients were considered.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.37-43
• /
• 1995

The procedure and the results of the full scale strain measurement of the long-range high-speed foil catamaran are described. The wave induced stresses at the center struts of the foils were measured during the sea trials in order to evaluate the hydrodynamic force acting on the foils and to verify the structural safety of the foil structures. From the statistical properties of the measured response of the stress, the most probable maximum values of the lift force and the stresses at the foils in service life of the ship are predicted and compared with the design parameters of the foils which were applied in the design of the subject ship. The available prediction processes of the measured stress are studied and the results of the applied processes are compared with each other.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.309-315
• /
• 2010

The CIIR blends, which is use for shoes outsole, with SSBR, XNBR and KBR were prepared with various mixing ratio. The viscoelastic properties of these blends, such as tensile modulus, rebound resilience, storage modulus, tan${\delta}$, and creep properties were measured. In the rebound resilience measurement, KBR showed the highest value, which means the lowest energy absorption to stress. As SSBR, XNBR and KBR blends with CIIR, the rebound resilience of the mixtures showed tendency to increase in arithmetic average. In the creep measurement, CIIR showed the highest visconse strain to stress, SSBR and KBR showed lower visconse strain. Maximum tan${\delta}$ peak of CIIR, SSBR and XNBR appeared at $-30^{\circ}C$, $5^{\circ}C$ and $0^{\circ}C$ respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.3
• /
• pp.193-199
• /
• 2002

Structral crack of RC structure generally occurs when the tension stress by applied load is larger than tension resistance of concrete, and it means deterioration of structure and the decrease of load resistance. Because structural crack of structure can occur critical damage to structure occasionally, the research on crack detection algorithm of RC structure is needed for assurance of structural safety and effective maintenance of structure. In this paper, we executed the laboratory test on measuring strain of RC beam's tension and compression zone, using strain gauge which is widely used on strain measurement of civil structure. By using measured strain, we analyzed strain change, elastic modulus change, and neutral axis change to detect crack of RC beam. As a result, we proposed the simple and effective crack detection algorithm using trends of neutral axis position change.

• Transactions of Materials Processing
• /
• v.8 no.1
• /
• pp.108-115
• /
• 1999

In this paper, the analysis of cold forging in final state has been performed by using rigid-plastic FEM. For the analysis, the geometry and flow stress of the workpiece are required. One method to obtain the geometry is measurement of that made from experimet. To evaluate the flow stress, average effective strain is calculated from the load-stroke diagram by using energy method. The numerical test performed to show the validity of propose method. The analysis of PFIR, the precision forging of spurgear with inside relif, is performed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.77-80
• /
• 1997

The torsion tests in the range of 900~110$0^{\circ}C$, 5.0$\times$10-2~5.0$\times$100/sec were performed to study the recry stallization behavior of 304 stainless steel in the high temperature multistage deformation. The no-recrystallization temperature(Tnr) and fractional softening(FS) were determined by the change of flow curves. The inflection points of stress slope were moved to lower temperature area as the strain rate and the interrupt time were increased. From the multipass flow curve, the intersection between pass stress and FS curve was corresponding to the pass which the FS dropped abruptly and it was shown that the recrystallization area could be determined by the FS measurement in multipass deformation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.1
• /
• pp.9-23
• /
• 1985

Boshin-Kak Bell, which is one of the largest bells, is located at Chong-Ro Square in the center of Seoul. The bell has been struct early morning and late evening for time-report since the 14th century in Lee Era. Therefore Boshin-Kak Bell has been an intimate old friend of Seoul citizen more than 500 years. Unfortunately, motal large cracks were found inside this bell in the horizontal and vertical directions in 1979. The present paper has investigated the propagated bell-crack by ultrasonic flaw detecting method, and the stress level, bell vibration and weight measurement by electric wire resistance strain gauge method. The results indicate that they are useful for further study of Korean bell by nondestructive test.

• 연구논문집
• /
• s.30
• /
• pp.93-99
• /
• 2000

Electro-Rheological(ER) fluids change their apparent viscosity according to the electric field strength. The electrical and rheological properties of zeolite based the ER fluids were reported. The electric field dependent yield stress are obtained from experimental investigation on the Bingham property of the ER fluid. Using ER fluids, it is possible to directly interface between electric drop and flow rate of the ER fluid was hydraulic control valve measured under application of an electric field. The purpose of the present study is pressure drop measurement of an ER valve by using strain gage. The performance characteristics of the valve system are evalusted in terms of pressrue fixed with respect to the intensity of employed electric fields and flow rates. As a result, it is esperimentally confirmed that pressure control valve using ER fluids applicable to use in hydraulic power systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.237-246
• /
• 2019

The Electro-Mechanical Brake (EMB) is the next generation braking system for automobiles and railway vehicles. Current brake systems for high-speed trains generate a braking force using a pneumatic cylinder, but EMB systems produce that force through a combination of an electric motor and a gear. In this study, an EMB operation mechanism capable of generating a high braking force was proposed, and structural and vibration analyses of the gears and shafts, which are the core parts of the mechanisms, were performed. Dynamic structural analysis confirmed that the maximum stress in the analysis model was within the yield strength of the material. In addition, the design that maximizes the diameter of the motor shaft was found to be advantageous in strength, and large shear stress could be generated in the bolt fixing the gear and eccentric shaft. In addition, a test apparatus that can reproduce the mechanism of the analytical model was fabricated to measure the strain of the fixed bolt part, which is the most vulnerable part. The strain measurement results showed that the error between the analysis and measurement was within 10%, which could verify the accuracy of the analytical model.