• Proceedings of the Korean Reliability Society Conference
• /
• 2004.07a
• /
• pp.303-311
• /
• 2004

This paper presents the reliability estimation of door hinge for home appliances, which consists of bushing and shaft. The predominant failure mechanism of bushing made of polyoxymethylene(POM) is brittle fracture due to decrease of strength caused by voids existing, and that of shaft made of acrylonitrile-butadiene-styrene(ABS) is creep due to plastic deformation caused by excessive temperature and lowering of glass transition temperature by absorbed moisture. Since the brittle fracture of bushing is overstress failure mechanism, the load-strength interference model is used to estimate the failure rate of it along with failure analysis. By the way, the creep of shaft is wearout failure mechanism, and an accelerated life test is then planned and implemented to estimate its lifetime. Through the technical review about failure mechanism, temperature and humidity are selected as accelerating variables. Assuming Weibull lifetime distribution and Eyring model, the life-stress relationship and acceleration factor, B$_{10}$ life and its lower bound with 90% confidence at worst case use condition are estimated by analyzing the accelerated life test data.a.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.432-440
• /
• 1993

Ductile cast iron has a good ductility and toughness than those of gray cast iron, because the shape of graphite is spheroidal. Also, it has been reported that, additional strengthening and toughening of the ductile cast iron can be obtainded from the proper combination of matrix structures by the heat treatment and addition of alloying elements. In this study the effect of special heat treatment and addition of alloying elements(Ni, Mo) on the multi-phase(ferrite-bainite-martensite) structures, strength and toughness of ductile cast iron were studied systematically. In water quenching from $770^{\circ}C$, the martensite volume(%) increased, but the ferrite volume(%) decreased with increment of Ni content. In as cast, pearlite volume(%) and hardness increased with increment of Mo and Ni contents. And with the increment of the destabilization austempering holding time, the bainite volume(%) increased but the martensite volume(%) decreased. As destabilization austempering holding time is same, bainite volume(%) decreased, martensite increased with the increment of Ni and Mo contents. The hardness and tensile strength decreased, but impact energy increased with the decrease of Ni and Mo contents, and increment of holding time of destabilization austempering treatment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.2
• /
• pp.304-311
• /
• 1998

The purpose of this study was to evaluate the shear bond strength on dentin of bonding agents based on glass ionomer cements, and to establish the appropriate method of bonding which has biological safety and decrease the pulpal damage. Fuji Bond LC, Advance, All Bond 2 and Scotchbond Multipurpose were applicated on occlusal dentin layer in acrylic resin block. Each group was composed of 10 specimens and the shear bond strenth between dentin layer and composite resin was measured with the Universal Testing Machine and analyzed. The result were as follows: 1. When using ANOVA and Scheffe' s multiple range test, there were not statistical differences among the four group. (P < 0.05) 2. The shear bond strength was high in the order of C, D, A. B and bond strength of group B showed relatively lower. 3. In digital image processing, there were not significant differences on morphology of failure surface.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.145-152
• /
• 2015

The article aims to apply a friction stir spot welding for producing the lap joint between AA5052 aluminum alloy and C11000 copper alloy. The dimension of the materials was 100 mm in length, 30 mm in width and 1.0 mm in thickness. The copper plate was set overlap the aluminum plate by 30 mm. The welding parameter was the rotating speed of 2500-4000 rpm, the pin inserting rate of 2-8 mm/min and the holding time of 6 sec. The mechanical properties test and the microstructure investigation were performed to evaluate the lap joint quality. The summarized results are as follows. The friction stir spot welding could produce effectively the lap joint between AA5052 and C11000 copper. Increase of the rotating speed and holding time directly affected to decrease the tensile shear strength of the lap joint. The optimized welding parameters in this study that indicated the tensile shear strength of 864 N was the rotating speed of 3500 rpm, the pin inserting rate of 6 mm/min and the holding time of 4sec. The experimental results also showed that the hardness of the weld metal was lower than that of the base materials.

• Korean Journal of Materials Research
• /
• v.30 no.2
• /
• pp.87-92
• /
• 2020

This study deals with the effects of austempering time on the microstructure and mechanical properties of ultra-high strength nanostructured bainitic steels with high carbon and silicon contents. The steels are composed of bainite, martensite and retained austenite by austempering and quenching. As the duration of austempering increases, the thickness of bainitic ferrite increases, but the thickness of retained austenite decreases. Some retained austenites with lower stability are more easily transformed to martensite during tensile testing, which has a detrimental effect on the elongation due to the brittleness of transformed martensite. With increasing austempering time, the hardness decreased and then remained stable because the transformation to nanostructured bainite compensates for the decrease in the volume fraction of martensite. Charpy impact test results indicated that increasing austempering time improved the impact toughness because the formation of brittle martensite was prevented by the decreased fraction and increased stability of retained austenite.

• Journal of Korea Foundry Society
• /
• v.28 no.6
• /
• pp.268-272
• /
• 2008

Interfacial characteristics of aluminum borate whisker reinforced AS52 matrix composite was investigated. Peak hardness of AS52 composite was obtained aging at $170^{\circ}C$ for 15h and the aging process was accelerated by the presence of the aluminium borate whisker. The MgO layer, which was the interfacial reaction product between the reinforcement and the Mg matrix, was produced with 20 nm thickness in as-cast condition. As the aging time increased, the thickness of the interfacial reaction layer increased to 50 nm in peak aged condition. The nano-indentation test results indicated that the strength of interface was improved by the aging but over-aging degraded the reinforcement and decreased the interfacial strength which resulted in the decrease of overall composite strength.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.55-60
• /
• 1981

Some physical properties of Ni-Cr based alloy for porcelain veneering were compared after repeated casting without the addition of any new alloy. The specimen were cast in a centrifugal caster with an oxygen-propane torch at optimum temperature. The obtained results were as follows: 1. The yield strength and hardness of the second generation were no significant differences compared with first generation but the yield strength and hardness of the third generation slightly decrased. 2. The ultimate tensile strength and elongation appeared to decrease slightly in second, third generations. 3. The tensile fractured facets of the first generation specimen were normal in all specimen, but in the second generation there were six tensile specimen out of ten, in the third there were four tensile specimen out of ten.

• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.211-218
• /
• 2000

The attrition-milled powder mixtures of Al and Al2O3 were oxidized below 140$0^{\circ}C$ for 1 hr and post-sintered at 150$0^{\circ}C$ and 1$600^{\circ}C$ for 2 hr. During attrition milling, ZrO2 was added to the system by grinding effect of ZrO2 balls. The average particle size of the powder mixtures was decreased by the attrition milling as the aluminum content decrease. Above 120$0^{\circ}C$, sintering behaviro was observed on the fine Al2O3 particles resulted from the oxidation of Al. The specimens heat-treated at 140$0^{\circ}C$ for 1 hr showed the bending strength of 166 MPa and hardness of 220 MPa. The specimens post-sintered at 1$600^{\circ}C$ for 2hr had a linear shrinkage of 9~12% and a relative density of about 95%. After the post-sintering, the specimens having 55 vol% Al content revealed the bending strength of 513 MPa and hardness of 718 MPa. The Weibull modulus to the bending strength was about 16.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.945-948
• /
• 2008

The effects of polymer-cement ratio on strength properties of ultrarapid-hardening acrylic-modified concretes. As a result, the flexural and tensile strengths of ultrarapid-hardening acrylic-modified concretes increase with increasing of polymer-cement ratio. In particular, the acrylic-modified concretes with a polymer-cement ratio of 20% provide approximately 1.5 times higher flexural and tensile strengths than unmodified concretes. Such high strength development is attributed to the high flexrul and tensile strengths of arcylic polymer and the improved bond between cement hydrates and aggregates because of the addition of acrylic polymer. However, the compressive strengths of ultrarapid-hardening acrylic-modified concretes decrease with increasing of polymer-cement ratio.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.76-81
• /
• 2008

UV curable pressure sensitive adhesive (PSA) was made by blending the di-functional or hexa-functional urethane-acrylate oligomer with synthesized acrylic PSA. The change of adhesive property and removability were investigated at various oligomer contents under each oligomer. As the content of oligomer increased, the peel strength was increased before UV irradiation, but it was decreased after UV irradiation. Also, it was observed that the peel strength increased with decrease of storage modulus (G'), and that loss factor (tan ${\delta}$) of the adhesive material affected the adhesive properties and removability.