• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.25-31
• /
• 2006

Controlled Auto Ignition(CAI) combustion has great potential in achieving significant increase in engine efficiency, while simultaneously reducing exhaust emissions. The process itself involves the auto ignition and subsequent simultaneous combustion of a premixed charge. In this study, NVO(Negative Valve Overlap) system was applied to a CAI engine in order to use residual gas. The fuel was injected directly to the cylinder under the high temperature condition resulting from heating the intake port to initiate CAI combustion. This paper introduced the valve timing strategy and experimental set-up. From this study, the effect of engine speed and valve timing on CAI combustion and exhaust emissions was clarified. In addition, stratified charge method was used to extend CAI operating region.

• 대한기계학회논문집B
• /
• 제39권1호
• /
• pp.45-51
• /
• 2015

최근 강화되는 연료소비율과 배기 규제에 대응하기 위해 자동차용 엔진에 다양한 신기술들이 적용되고 있다. 직접분사식 희박연소 엔진은 안정적인 성층혼합기 연소를 통해 연료소비율 및 배출가스 개선이 가능하지만 과잉공기 조건에서 상대적으로 높은 수준은 질소산화물의 배출은 해결되어야 할 과제이다. 본 연구에서는 직접분사식 희박연소 LPG 엔진에서 가변 밸브 기구를 이용한 흡기 및 배기밸브 시기의 변경이 엔진의 성능 및 배출가스에 미치는 영향을 파악하고자 하였다. 스로틀링을 하지 않은 부분부하 운전 조건에서 흡기밸브 열림 시기의 진각은 공기과잉률의 증가에 의한 질소산화물 배출 증가에 원인으로 작용하였다. 배기밸브 열림 시기를 진각할 경우 팽창일 감소와 펌핑손실 증가에 의해 연료 소비율이 악화되었다.

• 동력기계공학회지
• /
• 제12권4호
• /
• pp.5-11
• /
• 2008

The RI gasoline engine haying a sub-chamber had a high cycle variation due to the difficulty of the residual gas scavenge in the sub-chamber. To solve this problem and improve the combustion performance of RI engine, we devised a method to inject directly CNG fuel into the sub-chamber. A DI diesel engine of single cylinder was converted into a RI-CNG engine and an electronic control unit for the engine was manufactured. In this study, the combustion characteristics of the RI-CNG engine were investigated with the injection timings and air excess ratios at the load conditions of 50% throttle open rate and 1700rpm. As the results from this study, the RI-CNG engine worked reliably under the condition of the ignitable lean limit of $\lambda=1.7$ by showing the $COV_{imep}$ below about 5%. And the highest thermal efficiency could be obtained in the injection timing that produced the high imep and the low $COV_{imep}$ at the same time. The CO emission concentration indicated very low values and the THC and $NO_x$ showed an opposite pattern. With a view to improving the thermal efficiency and reducing the harmful emissions, the proper control region of the ignition timing and the mixture ratio were nearly ATDC $20^{\circ}\sim50^{\circ}$ and $\lambda=1.4$ respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권1호
• /
• pp.37-47
• /
• 2002

Recently gasoline direct injection method has been applied to gasoline engine to reduce fuel consumption rate by controlling fuel air mixture on lean condition by means of stratified charging, and to reduce simultaneously. Pollutant emissions especially NOx and CO by lowering the combustion temperature. But difficulty of controling local fuel air ratio at ignition area in flammability limit unavoidably appeared, because it is merely controlled by injection timing with spatial and temporal distribution of fuel mixture. In this study, the authors devised a uniquely shaped combustion chamber so called three-chamber GDI engine, intended to keep the more reliable fuel air ratio at ignition area. The combustion chamber is divided into three regions. The first region is in the rich combustion division, where the fuel is injected from the fuel injection valve and ignited by the spark plug. The second region is in the lean combustion division, where the combustion gas from the rich combustion division flows out and burns on lean condition. And the last region is in the main combustion division ie in the cylinder, where the gas from the above two combustion divisions mixed together and completes the combustion during expansion stroke. They found that the stable range of operation of three-chamber GDI engine on low-load condition exists in the lean area of average equivalence ratio. And they also found that the reformed engine reveals less specific fuel consumption and less pollutant emissions compared with conventional carburettor type gasoline engine.

• 한국분무공학회지
• /
• 제8권1호
• /
• pp.23-28
• /
• 2003

When a cold HPSI (High Pressure Safety Injection) fluid associated with a design basis accident, such as LOCA (Loss of Coolant Accident), enters the cold legs of a stagnated primary coolant loop, thermal stratification phenomena may arise due to incomplete mixing. If the stratified flow enters a reactor pressure vessel downcomer, severe thermal stresses are created in a radiation embrittled vessel wall by local overcooling. Previous thermal-mixing analyses have assumed that the thermal stratification phenomena generated in stagnated loop of a partially stagnated collant loop are neutralized in the vessel downcomer by strong flow from unstagnated loop. On the basis of these reasons, this paper presents the thermal-mixing analysis results in order to identify the fact that the cold plume generated in the vessel downcomer due to the thermal stratification phenomena of the stagnated loop is affected by the strong flow of the unstagnated loop.

• 한국자동차공학회논문집
• /
• 제19권6호
• /
• pp.82-89
• /
• 2011

Ultra lean combustion with stratified air-fuel mixture is one of the methods that can improve fuel economy of gasoline engines. The aim of this study is to show that how much fuel economy is improved and what are differences in engine control of the ultra lean combustion compared with stoichiometric combustion. In this study, the BMW N53 GDI engine, which is one of ultra lean combustion GDI engines introduced in the market recently, was tested at various engine operating conditions. Results indicated that fuel consumption rates were improved by 11.9~25.8% by the ultra lean combustion compared with stoichiometric combustion. It was also found that multiple fuel injection, multiple spark, early intake valve opening, and large vlave overlap duration were the features of the ultra lean combustion for combustion stability and emission improvement.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2477-2487
• /
• 2021

To improve safety analysis technology for a nuclear reactor containment considering an interaction between a reactor coolant system (RCS) and containment, this study aims at an experimental investigation on the integrated simulation of the RCS and containment, with an integral effect test facility, ATLAS-CUBE. For a realistic simulation of a pressure and temperature (P/T) transient, the containment simulation vessel was designed to preserve a volumetric scale equivalently to the RCS volume scale of ATLAS. Three test cases for a steam line break (SLB) transient were conducted with variation of the initial condition of the passive heat sink or the steam flow direction. The test results indicated a stratified behavior of the steam-gas mixture in the containment following a high-temperature steam injection in prior to the spray injection. The test case with a reduced heat transfer on the passive heat sink showed a faster increase of the P/T inside the containment. The effect of the steam flow direction was also investigated with respect to a multi-dimensional distribution of the local heat transfer on the passive heat sink. The integral effect test data obtained in this study will contribute to validating the evaluation methodology for mass and energy (M/E) and P/T transient of the containment.

• Clinical and Experimental Reproductive Medicine
• /
• 제49권3호
• /
• pp.185-195
• /
• 2022

Objective: This study aimed to determine the effect of sperm DNA fragmentation (SDF) on the cumulative live birth rate (CLBR) in intracytoplasmic sperm injection (ICSI) cycles in couples with unexplained infertility. Methods: We conducted a prospective study of 145 couples who underwent ICSI cycles for unexplained infertility. Based on the SDF rate, patients were categorized into a low SDF group (SDF ≤30%, n=97) and a high SDF group (SDF >30%, n=48). SDF was assessed using the acridine orange test on density gradient centrifugation prepared samples. The CLBR was calculated as the first live birth event per woman per egg collection over 2 years. Results: The high SDF group (SDF >30%) showed a significantly lower CLBR (p<0.05) and a significantly higher miscarriage rate (p<0.05) than the low SDF group (SDF ≤30%). No significant difference was observed in the implantation and cumulative pregnancy rates between the two SDF groups. The total number of embryo transfers was stratified further into fresh and frozen embryo transfers. In the fresh embryo transfers, there were significant differences in the implantation rates, clinical pregnancy rates, and live birth rates (p<0.05) between the low SDF and high SDF groups. However, in the frozen embryo transfers, there were no significant differences in clinical outcomes between the two groups. In the multivariable logistic regression analysis, SDF was a predictor of CLBR (p<0.05) when adjusted for possible confounding factors. Conclusion: High SDF was associated with a lower CLBR and a higher miscarriage rate in the ICSI cycles of couples with unexplained infertility.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1303-1310
• /
• 2001

In order to be applicable to the combustion modelling of stratified charged combustion like that of - lean burn and GDI engine, the correlations of laminar burring velocities fur several hydrocarbon fuels and methanol are needed over a wide range of equivalence ratio, pressure and temperature. In this study, these correlations are modeled in the 1311owing form based on the experimental and Muller\`s modeling results for several fuels, where $\alpha$, ξ, and ξ are functions of pressure and temperature, $S_{L}$ =$\alpha$ exp[-ξ($\Phi$-$\Phi$$_{m}$)$^{2}$ -exp {-ζ($\Phi$-$\Phi$$_{m}$)}-ζ($\Phi$-$\Phi$$_{m}$)]. By using the results calculated by PREMIX code with Sloane\`s detailed chemical reaction mechanism for propane, it is verified that the coefficients of the abode modeling can be determined by considering laminar burning velocity data only in a range of equivalence ratio less than $\Phi$$_{m}$. Therefore, Muller\`s modeling results can be adopted leer modeling of the pressure and temperature dependency. Compared with the results of the existing Keck'and Gulder's models, those of the present one showed the good agreement of the recent experimental data, especially in the range of lean and rich sides.s.des.s.

• 농촌의학ㆍ지역보건
• /
• 제14권1호
• /
• pp.16-29
• /
• 1989

The general objective of this study is to grasp the treatment expenses of common diseases by character of medical care institutions. The specific objective is to find out the treatment expenses for selected common diseases by type of medical care institutions and also by level of symptom. A record review method was employed to obtain required information for the analysis of expenses. A total of 40,000 cases treated by 85 medical care institutions were selected by the study team during the period 22 June to 14 July 1988. The 85 medical care institutions were sampled by stratified proportionate random sampling method. The major findings obtained from the information collected by the study team are as follows ; 1) Treatment expenses were composed of physical examination, medication, injection anesthesia, rehabilitation surgical intervention, lab test, X-ray and diagnosis. The highest expenses was for medication, accounted for 36.7% of the total: 13.9%, injection; Lab, tests respectively: 10.5%, physical examination : 8.6% surgical intervention; 7.9% admission : 6.3%, X-ray and diagnosis: 1.5%, rehabilitation. 2) Treatment expenses per case of common diseases were quite different from not only type of medical care institutions, such as university hospital, general hospital, hospital and clinic, but also from level of symptom. 3) Treatment expenses per case for the aged were higher than that of the young. The treatment cases for over 60 years of age accounted for 19.4% of the total, however the proportion of treatment expenses accounted for 23.8% of the total. 4) Duration of treatment and visits for same diseases varied from type of medical cara institutions. Based on these study findings, the following further research should be conducted: (1) Establishment of health care delivery system. (2) Feasibility of the development of health care programme for the aged. (3) Strengthening for primary health care approach.