• Nuclear Engineering and Technology
• /
• 제9권3호
• /
• pp.117-123
• /
• 1977

소입된 질칼로이-4의 가공시효(strain ageing) 현상에 미치는 시효시간 및 온도의 효과를 523-588 狂 온도 구간에서 1~52초의 짧은 시효기간에 조사하였다. 이 실험 조건하에서, 가공시효응력은 5.55$\times$$10^{-4}$ sec$^{-1}$ 신연속도(strain rate) 경우 시효시간 및 시효온도가 증가할수록 증가하였다. 소입된 질칼로이-4의 응력부하 하의 가공시효 현상이 두 한계로 나타나는 것이 확인되었는데 첫단계는 0.39ev의 활성화 에너지 값의 구간으로 이는 전위 (dislocation) 주위의 응력상태로 인한 침입형 산소원자들의 Snoek타입의 배열 (ordering)로 인한 것으로 고려되었으며 두번째 단계는 0.6ev 활성화에너지 값을 갖는 구간으로 이는 주로 산소원자들의 장범위확산에 기인하는 것으로 해석되었다.

• Nuclear Engineering and Technology
• /
• 제8권3호
• /
• pp.151-157
• /
• 1976

냉간가공한 질칼로이-4의 가공시효(strain ageing) 현상이 진공속에서 변형온도 및 1143ppm-3500ppm의 산소 함량의 변수로써 조사되었다. 가공시효 현상이 0-10 % 냉간가공한 질칼로이-4의 경우 200-45$0^{\circ}C$의 온도구간에서 조사되었으며, 이때 가공시효 현상은 냉간가공량이 증가할수록 감소하는 현상을 보였다. 이 냉간가공에 따른 가공시효의 감소는 냉간가공시 발생한 결함에 의해 산소 원자들이 trapping 되는 결과로 기인된 것으로 고려된다. 냉간가공된 질칼로이-4의 최대 가공시효 응력은 함유된 산소의 량의 평방근에 비례한다는 사실이 밝혀졌다.

• Nuclear Engineering and Technology
• /
• 제5권1호
• /
• pp.55-64
• /
• 1973

압축변형시킨 순천(0.007% 탄소포함)을 8$0^{\circ}C$이하에서 저온열처리(ageing)한 후, 열처리시간에 따라 증가하는 저항복점(lower yield point)의 변화를 압축시험으로 측정하여 그 strain ageing 효과를 조사했다. 본 실험에서 압축변형된 순철의 strain ageing 속도는 저항복응력의 증가가 그치고 중가의 60% 정도에 이를 때까지 열처리시간의 2/3승에 비례했으나, 이미 알려진 인장변형의 경우에서보다 느렸다. 이 60%의 증가는 순철을 6$0^{\circ}C$에서 약 5시간 열처리함으로써 얻었다. 압축변형된 순철의 strain ageing을 위한 활성화에너지는 열처리의 초기단계(6$0^{\circ}C$에서 약 30분)에서 21,500 cal/mole이었는데, 이것은 인장변형의 경우에서 알려진 것보다 대략 10%가 큰 값이다. 이 증가는 잔유응력에 의해 결정내에 형성되는 strain field로 설명되었다. 열처리공정의 둘깨단계(6$0^{\circ}C$에서 약 5시간까지 계속되는)에서는 그 활성화에너지가 다소 감소되는 경향이 있었다.

• 열처리공학회지
• /
• 제33권4호
• /
• pp.161-172
• /
• 2020

The tensile property of A5082 and A6060 aluminium wrought alloys was investigated, in terms of the strain rate sensitivity on alloy conditions by heat treatment and bake hardenability on pre-strain prior to strain ageing. The tensile test was carried out in a range of strain rate of 4.17 × 10^-5 s^-1 ~ 4.17 × 10^-5 s^-1 in room temperature and the nominal range of pre-strain was 3.0 ~ 10.5%. The tensile deformation of A5082 alloys is characterized as typical case of dynamic strain ageing with negative strain rate sensitivity for all conditions, and the tensile strength indicates a similar level regardless of alloy conditions, except only in full annealed condition. The stress-relief annealing on A6060 alloys can induce practical decrease in strength level of over approximately 100 MPa without any ductility loss, compared to as-rolled condition, while a full annealed and aged condition leads remarkable strengthening effect with the decrease of tensile elongation. Additionally, the bake hardenability of A5082 alloy by strain ageing indicates a negative dependence upon the increase of pre-strain, while A6060 alloy exhibits a positive sign even in low level relatively compared with conventional SPCC.

• Nuclear Engineering and Technology
• /
• 제8권1호
• /
• pp.19-27
• /
• 1976

질칼로이-4의 가공시효(strain ageing) 현상을 173-575$^{\circ}C$의 온도구간에서 소입된 시편과 소둔된 시편에 대해 각각 조사하였다. 소입된 질칼로이-4의 가공시효가 175-50$0^{\circ}C$구간체서 난타났으며, 3$25^{\circ}C$에서 극대값의 가공시효가 조사였었다. 반면 소둔된 시편의 경우엔 175-575$^{\circ}C$ 구간에 걸쳐 가공시효가 나타났으며, 이 온도구간 사이에 3$25^{\circ}C$ 및 45$0^{\circ}C$의 두 지점에서 극대값이 나타나는 것을 확인했다. 소입된 경우와 소둔된 경우에 모두 3$25^{\circ}C$에서 보인 가공시효의 극대값은 시효동안에 전위조직 속으로 침입형 산소원자들의 응집에 의한 결과로 고려되며 45$0^{\circ}C$에서 보이는 극대값은 철원자와 전위간의 작용에 기인된 것으로 해석된다. 질코늄 합금의 30$0^{\circ}C$ 근처에서 보이는 가공시효값은 첨가된 산소량의 평방근에 비례한다는 것이 확인됐다.

• 대한조선학회논문집
• /
• 제55권3호
• /
• pp.205-214
• /
• 2018

This paper deals with the experimental study on the hygrothermal ageing effect to the strength of Carbon Fiber Reinforced Plastics (CFRP) materials for marine leisure boat manufactured by vacuum assisted resin infusion method. The experiments performed consist of tensile, flexural and shear tests according to American Society for Testing and Materials (ASTM) and Korean Industrial Standards (KS) test methods. Test coupons are varied from uni-directional(UD, $0^{\circ}$, $90^{\circ}$), Bi-Directional (BD), and Double-Bias (DB) carbon fiber fabrics in conjunction with epoxy resin. The results of tensile test show that tensile strength reduces significantly while not the same degree of reduction is observed for elasticity modulus with respect to the existence of hygrothermal ageing effect. This implies that the tensile strain induced from external load holds steady values but ultimate strength values change widely under hygrothermal ageing effect. In case of the flexural test, $0^{\circ}$ UD shows more strength reduction than $90^{\circ}$ UD while BD has reduced values in both flexural strength and elasticity modulus under hygrothermal ageing effect. It is learned that the bending strain induced from external load and ultimate strength values are reduced with respect to hygrothermal ageing effect. Shear test performed only on DB materials, and the results show marginal reduction in ultimate strength and moderate reduction in elasticity modulus. This means that the shear strain varies more than ultimate shear strength with respect to hygrothermal ageing effect. The experiment conducted in this paper clearly demonstrates the differences in material properties of the CFRP for the consideration of hygrothermal ageing effect. Findings obtained from this experimental study can serve as a fundamental input data for the realistic structural responses of marine leisure boat built in CFRP materials.

• Smart Structures and Systems
• /
• 제6권3호
• /
• pp.225-238
• /
• 2010

We report on the development of a new technology for the fabrication of Micro-Electro-Mechanical-System (MEMS) strain sensors to realize a novel type of crackmeter for health monitoring of ageing civil infrastructures. The fabrication of micromachined silicon MEMS sensors based on a Silicon On Insulator (SOI) technology, designed according to a Double Ended Tuning Fork (DETF) geometry is presented, using a novel process which includes a gap narrowing procedure suitable to fabricate sensors with low motional resistance. In order to employ these sensors for crack monitoring, techniques suited for bonding the MEMS sensors on a steel surface ensuring good strain transfer from steel to silicon and a packaging technique for the bonded sensors are proposed, conceived for realizing a low-power crackmeter for ageing infrastructure monitoring. Moreover, the design of a possible crackmeter geometry suited for detection of crack contraction and expansion with a resolution of $10{\mu}m$ and very low power consumption requirements (potentially suitable for wireless operation) is presented. In these sensors, the small crackmeter range for the first field use is related to long-term observation on existing cracks in underground tunnel test sections.

• Nuclear Engineering and Technology
• /
• 제8권4호
• /
• pp.203-207
• /
• 1976

질칼로이-4에 있어서 flow stress strain rate 의존성을 냉간가공 및 소둔된 시편에 대해 20$0^{\circ}C$-45$0^{\circ}C$ 온도 구간에서 응력이완 실험으로 조사하였다. 전체 실험온도에서 In-3-ln i 관계식은 $10^{-5}$-$10^{-3}$ sec$^{-1}$ strain rate의 구간에 걸쳐 선형관계를 보였다. 냉간 가공된 질칼로이 -4의 strain rate sensitivity, m값은 30$0^{\circ}C$에서 최소값을 보인 반면, 소둔된 시편의 경우 30$0^{\circ}C$와 45$0^{\circ}C$에서 최소값들을 보였다. 최소값의 m이 나타나는 온도는 가공시효값이 극대값을 보이는 온도와 일치한다는 사실이 확인되었다. m값의 감소는 활동자유전위들이 산소원자에 의해 pinning된 결과로 유발되는 가공 시효와 관련된 것으로 고려된다. 그리고 소둔된 시편이 45$0^{\circ}C$에서 가지는 최소 m값은 철 원자들로 인한 가공 시효에서 기인된 것으로 생각된다.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.107-113
• /
• 2011

Coolant rubber hoses for automotive radiators under thermal and mechanical loadings can be degraded and thus failed due to the influences of the locally formed electricity. In this study, an advanced test method was developed to simulate the failure problem of the rubber hose. For carbon black filled EPDM (ethylene-propylene dine monomer) rubber used as a radiator hose material the ageing behaviors by the electro-chemical stresses combined with a tensile strain were analyzed. As the tensile strain increased, the current of the rubber specimen reduced indicating an increase of the internal defects and electrical resistance of the rubber specimen. Elongation at break and IRHD hardness rapidly decreased with increasing the ageing time. Both electro-chemical stress and mechanical tensile stress clearly accelerated the degradation of EPDM rubber.

• 한국주조공학회지
• /
• 제38권5호
• /
• pp.95-102
• /
• 2018

The dependence of the tensile properties on variations in the porosity of A356 aluminium alloys was investigated in terms of the quality index of the tensile properties based upon the ultimate tensile strength and elongation as well as the variation of the strength coefficient and strain-hardening exponent with regard to a T6 treatment. The test specimens were prepared by low-pressure die-casting and a subsequent T6 treatment, and the experimental results of a tensile test carried out at room temperature were compared to the theoretical description using a modified constitutive model. The nominal value of the quality index of A356 alloys increases gradually with a lapse of the ageing time upon a T6 treatment, despite the fact that this value is temporarily decreased during the initial stage of ageing from a solutionised condition. Additionally, the quality index depends practically upon the porosity variation with a power law relationship without regard to whether in solutionised or artificial aged conditions. The theoretical description indicates that the strength coefficient directly determines the nominal level of the quality index. Moreover, the overall dependence of the quality index on the porosity variation is remarkably weakened with an increase in the tensile strain, whereas the quality index depends sensitively upon the porosity variation with a low value of the strain-hardening exponent.