• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.342-345
• /
• 1996

This paper presents the basic characteristics of thin-film strain gauges using Cr thin-films, in which the Cr thin-films were deposited by DC magnetron sputtering. The optimized deposition conditions as a strain gauge were the input DC power was 7 W/$\textrm{cm}^2$ and the Ar vacuuming pressure was 9 mTorr. The characteristics of fabricated Cr thin-film strain gauge were the gauge factor(GF) was 5.86 in longitudinal strain and -2.04 in transverse one, the TCR was under 400 ppm/$^{\circ}C$ and the TCS was around 0 ppm/$^{\circ}C$.

• 센서학회지
• /
• 제20권3호
• /
• pp.213-218
• /
• 2011

The load cell is a force sensor and a transducer that is used to convert a physical force into a electrical signal for weighing equipment. Most conventional load cells are widely used a metal foil strain gauge for sensing element when force being applied spring element in order to converts the deformation to electrical signals. The sensitivity of a load cell is limited by its low gauge factor, hysteresis and creep. But silicon-based sensors perform with higher reliability. This paper presents the basic design and development of the silicon type load cell with an SUS630 diaphragm. The load cell consists of two parts the silicon strain gauge and the SUS630 structure with diaphragm. Structure analysis of load cell was researched by theory to optimize the load cell diaphragm design and to determine the position of peizoresistors on a silicon strain gauge. The piezo-resistors are integrated in the four points of silicon strain gauge processed by ion implantation. The thickness of the silicon strain gauge was polished by CMP under 100 ${\mu}M$. The 10 mm diameter SUS630 diaphragm was designed for loads up to 10 kg with 300 ${\mu}M$ of diaphragm thickness. The load cell was successfully tested, the variation of ${\Delta}$R(%) of four points on the silicon strain gauge is good linearity properties and sensitivity.

• 제어로봇시스템학회논문지
• /
• 제12권9호
• /
• pp.912-917
• /
• 2006

A strain gauge weight measuring instrumentation system was designed with RF sensor network facilities. In the sensor module system data conversion and a series of signal processing were totally equipped. 16 strain gauges are incoming sensors and each output of the strain gauge was amplified and filtered for proper analog signal processing. Several measuring instrumentation OP amps and general purposed OP amps were used. 12 bits A/D converters converted analog signals to digital bits and a PIC microprocessor controlled the 16 channels of strain gauges. RF RS232 modules were used for wireless communication between the PIC microprocessor and an Ethernet host far a remote sensor monitoring system development.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권3호
• /
• pp.133-138
• /
• 2003

FBG sensor의 다중 측정성을 이용하여 모르타르 시편의 열 변형률과 온도 변화를 동시에 측정하였다. 또한, 광섬유 격자 센서를 이용하여, 열 변화에 따른 모르타르 시편의 내부 온도 구배를 측정하였다. 열 변형률을 기존 strain gauge와 함께 측정하였을 때, strain gauge는 섭씨 60도 이상의 온도에서 오차를 보이는 반면, FBG 센서는 안정된 측정값을 나타냈다. FBG 온도 sensor로 측정한 온도 변화량은 thermocouple로 측정한 값과 비교하였으며, 선형적인 대응관계를 보였다.

• 한국전자통신학회논문지
• /
• 제18권1호
• /
• pp.185-194
• /
• 2023

군 무기체계에 널리 적용되는 4축 스트레인 게이지는 열악한 온도와 진동조건에서 운용되기 때문에 오차가 커지게 되고, 오동작을 일으킬 수 있다. 이를 개선하기 위해 본 논문에서는 군 무기체계에 적용되는 4축 스트레인 게이지의 오차에 대한 신호처리 소프트웨어 기법을 제안한다. 첫째, 주위 온도에 따른 스트레인-게이지의 오차와 신호처리회로의 오차를 평가하고 분석하였고, 둘째, 스트레인-게이지의 오차를 개선할 수 있는 불감대 영역과 오프셋 영역의 처리에 대한 소프트웨어 기법을 제안한다. 소프트웨어 기법을 적용한 실험결과는 온도시험과 운용시험에서 정상적으로 동작하는 것을 확인하였다. 따라서, 제안한 소프트웨어 기법은 타당하므로, 스트레인-게이지를 사용하여 시스템을 설계할 때 주위 온도와 진동에 따른 오차 개선에 유용한 정보로 사용될 수 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권3호
• /
• pp.438-443
• /
• 2006

The probe type sensor using strain gauges was used to track a container box's seam in this paper. A strain gauge has a property which the specific resistance is changed by varying of the sectional area and length when tensile and compressive stresses are generated at the strain gauge. We designed the automatic seam tracking device by attaching the probe type strain gauge sensor, motor driving slide, encorder to check the moving distance and interface card connected MPU upside the speed controllable carriage. The folded work piece for a container box is made to examine whether the device can track the seam automatically or not. Seam tracking experiments were done by changing the carriage moving speed at 300. 400. 500. 600[mm/min] each as the voltage of side track was 2.5[V]. We compared and analyzed the sampling data which is obtained by output voltage of strain gauge sensor and rotary encorder pulse every 100 [m/s]. The welding experiments were performed by using $CO_2$ welding machine about the carriage moving speed that has good seam tracking condition in the seam tracking experiments above. And we compared the seam tracking status.

• 센서학회지
• /
• 제22권5호
• /
• pp.321-326
• /
• 2013

In this paper, the usability of a compact silicon strain gauge load cell in a weighting disdrometer for measuring the impact load of a falling raindrop is introduced for application in a multi-meteorological sensor. The silicon strain gauge load cell is based on the piezoresistive effect, which has a high linearity output from the momentum of the raindrop and the simplicity of signal processing. The weighting disdrometer shows a high sensitivity of 7.8 mV/g in static load measurement when the diaphragm thickness of the load cell is $250{\mu}m$.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.147-155
• /
• 2002

교량의 안전성과 사용성을 검토하기 위해서는 외적 하중에 대한 구조 부재의 거동 특성과 정확한 저항 능력 평가가 반드시 고려 되어야 한다. 구조 부재의 거동 특성과 저항능력을 평가하기 위해서는 구조물의 변형률과 변위가 반드시 측정 되어야 한다. 변형률 측정을 위해서 전기 저항식 변형률 게이지를 사용하는 것이 보통이다. 그러나 교량의 교각이 높고, 장지간을 갖는 경우 변형률 게이지 부착은 매우 어렵고 경제적이지 못하다. 또한 구조 부재에 균열이 많이 발생되어 있거나 습윤 상태라면 전기 저항식 변형률 게이지에 의한 변형률 계측은 추천할만한 방법이 못된다. 따라서 본 연구에서는 이러한 단점을 보완 할수 있도록 측정 변위를 이용한 변형률 해석 알고리즘을 제안 하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.220.2-220.2
• /
• 2005

• 한국기계가공학회지
• /
• 제13권4호
• /
• pp.75-82
• /
• 2014

A pin-type load-cell which uses shear-type strain gauges was developed to measure the tension of a wire in a winch. A finite element analysis was performed to determine the locations of the strain gauges. All of the shear-type strain gauges were attached onto parts that undergo regularly shear stress distributions. A Wheatstone bridge circuit was used to connect each of the gauges and to measure the strains. Linearity within the 5% error range was noted when testing the pin-type load-cell.