• 한국연초학회지
• /
• 제15권1호
• /
• pp.57-62
• /
• 1993

Ridger and vinyl mulcher for 8-10 PS power tiller which were distributed at the rate of one out of 2.3 farm households in Korea, was developed to ease the labor shortage of tobacco production. Devices wheel shaft extension by 30cm at both sides improved the stability of straight drive and enabled to save required labor hours by 50% for ridging at sloping field. Screw type blades were attached on center drive rotavator shaft, gear set was deviled to reverse the rotavator, and it was good at need to adjust the width and height for ridge. As the results, required labor hours for ridging and vinyl mulching could be saved by 90% as compared to conventional manual method after cattle plowing, and by 50% as compared to conventional power tiller method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.650-653
• /
• 2001

In recent the energy efficiency of a refrigerator has been restricted extremely. A compressor consumes a great portion of input power in a refrigerator. So it is necessary to develop a more efficient compressor in these days. The existing reciprocating compressor need to a crank shaft to convert the rotating motion to the straight motion and is not efficient. But the linear compressor using mechanic resonance is efficient but need a drive instead of a crank shaft to control a position accurately. However it is impossible to apply a stroke sensor practically because of the internal circumstance of compressor. In this paper, A new sensorless stroke control method using the current and voltage of linear compressor is proposed.

• 수산해양기술연구
• /
• 제18권1호
• /
• pp.39-46
• /
• 1982

박용추진축계의 최적배치상태를 얻기 위해 선형계획법에 의한 최적배치 전산프로그램을 개발했으며, 여기에 필요한 자료들은 삼차모먼트정리를 매트릭스산법으로 전산처리해서 얻어냈고, 이 프로그램의 신속성을 확인하기 위해 모형축의 계산치와 스트레인 게이지에 의한 실측치를 비교하고, 실선축계에 적용한 결과 다음과 같이 요약할 수 있었다. 1. 최적배치의 필수자료인 직선지지상태의 반력 및 반력경향계수를 구하는 전산프로그램을 개발해서, 모형축에 적용한 결과, 실험치와 계산치가 거의 일치했고, 실선축에 대해 계산한 값도 타 프로그램으로 계산한 것과 거의 비슷했다. 2. 본 논문의 스트레인게이지에 의한 축계상태치의 계측방법은 실선축의 배치상태의 조정시에 매우 효과적으로 활용할 수 있을 것이다. 3. 최적배치의 전산프로그램을 실선축에 적용한 결과, 제한조건을 만족하려면, 지지베어링들을 상당량 수직방향으로 조절해야 함을 알 수 있었다. 따라서 최적배치의 관건은 배치계산에 필요한 정확한 자료와 제한조건을 구하는 것이라 할 수 있겠다.

• 한국지반공학회논문집
• /
• 제23권4호
• /
• pp.59-68
• /
• 2007

본 논문에서는 토조에 실시된 모형말뚝 재하실험과 콘관입실험을 통하여, 말뚝형태별 지지력 특성분석과 CPT지지력 상관계수를 평가하였다. 고려된 말뚝의 형태는 일반적인 현장타설말뚝에 적용되는 원통형 말뚝과 테이퍼형 말뚝이 고려되었다. 본 연구는 궁극적으로 강관주 송전탑의 기초구조물 형식개발과 설계기준 수립을 목표로 하고 있으며, 이를 위해 기초형식별 거동과 지반상태의 영향 등을 중점적으로 살펴보았다. 말뚝 토조실험을 통해 나타난 결과에 의하면, 원통형 및 테이퍼형 말뚝의 전체지지력의 차이는 크지 않았으나, 개별 지지력요소의 거동은 말뚝형태별로 상이한 것으로 나타났다. 토조실험결과와 동일한 지반조건에 대해 수행된 CPT결과를 통해 말뚝지지력과 콘지지력의 관계를 나타내는 CPT지지력 상관계수의 변화추이를 도출하였다. CPT상관계수는 원통형 및 테이퍼형 말뚝형태를 비교함으로써 나타내었으며, 선단지지력과 주면마찰력의 요소별 변화추이를 제안하였다.

• Archives of Plastic Surgery
• /
• 제36권2호
• /
• pp.225-228
• /
• 2009

Purpose: Urethral reconstruction following failed hypospadias repair is difficult because of a severe shortage of the skin on ventral surface of the penis. We experienced a successful reconstruction of a failed hypospadias repair using the radial forearm free flap. So we present our case. Methods: A 16 - year - old boy had a proximal shaft hypospadias and had been taken a transverse preputial island flap but it completely broke down. There was no spare skin on the shaft of the penis. So we reconstructed a neo - urethra and the ventral skin of the penis with the radial forearm free flap. Results: Postoperatively he made relatively good process. The urethral catheter was maintained for 10 days and self - voiding was started. The suprapubic catheter was removed at the postoperative 30th day after control of cystitis. The postoperative appearance of the penis is acceptable and a straight erection is achieved. Conclusion: In the scarred penis with hypospadias, the radial forearm free flap transfer is a reliable reconstructive method for the neo - urethra and the ventral skin of the penis.

• 한국기계가공학회지
• /
• 제13권1호
• /
• pp.45-51
• /
• 2014

Generally, marine transmissions contain straight shafts and helical gears, meaning that enginerooms require more space. In order to guarantee a levelengine space for conical involute gears or beveloid gears, both of which are important machine parts, a conical gear was used to replace the traditional cylinder gear. Owing to weak points such as the point contact phenomenon of the teeth, a limitation of the width of each tooth in terms of the addendum, the variational modification coefficient,and the difficulty of processing, research about conical involute gears remains at a standstill. Along with the increasing number of applications of conical involute gears, research on conical gear design technology is necessary. In this paper, in an effort to enhance conical gear design technology, research on the 3D modeling and stress analyses of helical conical involute gears were done.

• Journal of Advanced Marine Engineering and Technology
• /
• 제3권1호
• /
• pp.32-39
• /
• 1979

Alignment of marine engine shafting generally implies a judicious slope alignment of supporting bearings in order to achieve acceptable values of bearing reactions and shaft stresses for all deformation conditions of hull. Authors developed a computer program, which computes the bearing reaction forces, the bearing reaction influence numbers and etc, using quadruple integration method. And the results of calculation for a 26,000 DWT steam container carrier were in good agreements with those of foreign shipyard. Also they introduced the optimization technique of slope alignment combined technical economic basis, and as a result of comparing characteristics of shafting in case of straight alignment whit those in case of slope alignment, the latter was found to be much better than the former.

• 한국동물학회:학술대회논문집
• /
• 한국동물학회 1998년도 공동 춘계학술대회
• /
• pp.33-33
• /
• 1998

The most recent, Jeong and Nakabo (1997) described Raja koreana as a new species based on an adult female specimen collected from the southwestern coast of Korean Peninsula. Raja koreana has several unique characters not shared with any other supraspecific taxa of Rajoidei, but it was provisionally included in the genus Raja because of having no information of its clasper. Later, two mature males and a few specimens of the species were collected from near the type locality. Therefore, a new genus should be erected for this species. The new genus is characterized by the followings: Rostral shaft straight, narrow and thick in depth: unsegmented base with filamentous cartilage. Dorsal surface of tail with a row of distinct thorns along midline, patches of distinct thorns anterior to first dorsal fin and between first and second dorsal fins in bathe sexes; most thorns directed anteriorly, and thornlets directed posteriorly. Scapulocoracoid comparatively short and high, rear corner high, without anterior bridge, postventral fenestra expanded. Distal tip of accessory terminal 1 claspser cartilage well separated from the tip of accessory terminal 2 clasper cartilage.

• 해양환경안전학회지
• /
• 제25권7호
• /
• pp.927-935
• /
• 2019

연안 해역에서 소형 선박의 프로펠러 고장으로 인한 사고가 지속적으로 발생하고 있다. 특히, 해상부유물(폐그물 및 로프 등)에 의하여 선박 프로펠러가 감기는 사고가 빈번히 일어나고 있다. 선박 프로펠러 감김 사고는 동력 상실로 인한 선박의 운항 지연 및 표류로 인한 1차 사고와 프로펠러에 감긴 로프을 제거하기 위한 잠수 작업등으로 인한 2차 사고의 우려가 있다. 이러한 빈번한 프로펠러 감김 사고에도 불구하고 문제를 해결할만한 적절한 도구가 없어 선박을 육상으로 인양하여 수리하거나, 잠수부가 직접 선박 아래로 잠수하여 문제를 해결하고 있는 실정이다. 이에 따라, 최근 선박 프로펠러 감김 사고를 예방하기 위해 프로펠러 샤프트에 로프절단장치를 일부 소형선박에 장착하고 있으나 비교적 높은 설치비용 및 시간이 으로 인하여 원활하게 적용되어지지 않는 것으로 판단된다. 본 연구에서는 이러한 문제점을 해결하기 위해 기계톱 원리를 이용한 간단한 구조를 가진 수중절단기 기구 설계 및 제어기 개발을 수행하였다. 수중절단기의 톱날은 직선왕복동작을 위해 유성기어와 크랭크핀을 사용함으로써 긴 행정을 가질 수 있도록 하였다. 또한 수중절단기는 소형 선박에 비치되어있는 배터리를 이용하여 작동시킬 수 있도록 하였다. 또한, 비전문가인 사용자가 보다 편리하고 안전하게 사용할 수 있도록 역전류 방지 및 속도제어회로를 적용하여 편리성 및 안정성을 확보하였다.

• 한국운동역학회지
• /
• 제15권4호
• /
• pp.181-189
• /
• 2005

To know the proper impact posture and changes for the various clubs, changes of impact variables according to the change of golf club length was investigated. Swing motions of three male low handicappers including a professional were taken using two high-speed video cameras. Four clubs iron 7, iron 5, iron 3 and driver (wood 1) were selected for this experiment. Three dimensional motion analysis techniques were used to get the kinematical variables. Mathcad and Kwon3D motion analysis program were used to analyze the position, distance and angle data in three dimensions. Major findings of this study were as follows. 1. Lateral position of the head remained more right side of the target up to 3.5cm compared to the setup as the length of the club increased. 2. Left shoulder raised up to 5cm and right shoulder lowered up to 2.5cm compared to setup. The shoulder line opened slightly (maximum 11 degrees) to the target line. 3. Forward lean angle of the trunk decreased up to 4 degrees (more erected) compared to setup. 4. Side lean angle of the trunk increased compared to setup and increased up to 16 degrees as the club length increased. 5. The pelvis moved to the target line direction horizontally and opened up to 31 degrees. Right hip moves laterally to the grip position at the setup. 6. Flexion of the left leg maintained almost constantly but the right leg flexed up to 11 degrees compared to setup. 7. Left arm is straightened but the right arm flexed about 20degrees compared to straight. 8. Center of the shoulders were in front of the knees and toes of the feet. 9. Hands moved to the left (8.7cm), forward (5.7cm) and upward (11.6cm) compared to the setup. This is because of the rotation of pelvis and shoulders. 10. Shaft angle to the ground was smaller than the lie angle of the clubs but it increased close to the lie of the clubs at impact.