• 한국수소및신에너지학회논문집
• /
• 제13권2호
• /
• pp.110-118
• /
• 2002

The hydrogen storage vessel having a good heat conductivity along with a simple structure and a low cost for these alloys was designed and manufactured, and then its characteristic properties were studied in this study. The various parts in hydrogen storage vessel consisted of copper pipes and stainless steel of 250 mesh reached the setting temperature after 4~5 minutes, which indicated that storage vessel had a good heat conductivity that was required in application. And also the storage vessel had a good property of hydrogen transport considering that the reaction time between hydrogen and rare-earth metal alloys in storage vessel was found to be within 10 min at $18^{\circ}C$ under 10 atmospheric pressure. It showed that the average capacity of discharged hydrogen volume was found to be $120{\ell}$ for $MmNi_{4.5}Mn_{0.5}$ under discharging conditions of $40^{\circ}C{\sim}80^{\circ}C$ at a constant flow rate of $5{\ell}$/min. It was found that the optimum discharging temperature for obtaining an appropriate pressure of 3atm was determined to be $60^{\circ}C$ for $MmNi_{4.5}Mn_{0.5}$ hydrogen storage alloy.

• 한국가스학회지
• /
• 제27권2호
• /
• pp.95-103
• /
• 2023

본 논문에서는 가스압력을 고려할 때 수소가스 저장용기(Type 1)의 거동특성을 평가하기 위해 ISO 18119의 노치형상에 따라 수소가스 저장용기에서 발생한 VMS(von Mises stress)을 유한요소법으로 해석하였다. 해석결과에 따르면 길이방향 노치에서 발생한 최대 VMS가 원주방향 노치보다 높게 발생하였다. 또한, 저장용기의 거동시 발생한 응력을 VMS와 재료의 항복강도 비인 응력비로 분석하였다. 해석결과에 따르면 노치가 길이방향으로 형성된 저장용기의 경우 가스압력 50 MPa에서 저장용기 내부와 외부가 각각 0.85와 0.50로 증가하였으나 1보다 낮게 분석되었다.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.249-257
• /
• 2010

In this paper, a three-dimensional hydrogen absorption model is developed to precisely study hydrogen absorption reaction and resultant heat and mass transport phenomena in metal hydride hydrogen storage vessels. The 3D model is first experimentally validated against the temperature evolution data available in the literature. In addition to model validation, the detailed simulation results shows that at the initial absorption stage, the vessel temperature and H/M ratio distributions are uniform throughout the entire vessel, indicating that the hydrogen absorption is so efficient during the early hydriding process and thus local cooling effect is not influential. On the other hand, nonuniform distributions are predicted at the latter absorption stage, which is mainly due to different degrees of cooling between the vessel wall and core regions. This numerical study provides the fundamental understanding of detailed heat and mass transfer phenomena during hydrogen absorption process and further indicates that efficient design of storage vessel and cooling system is critical to achieve fast hydrogen charging and high hydrogen storage efficiency.

• 소성∙가공
• /
• 제17권4호
• /
• pp.292-301
• /
• 2008

Type 2 compressed natural gas(CNG) storage vessels for automobiles are becoming widely used. They are not only supplied to automakers in Korea, such as Hyundai Motors, but increasingly, they are being exported overseas. Autofrettage is a process that produces beneficial residual stresses in a vessel by subjecting it to excessive internal pressure. This strengthens the vessel and improves its fatigue resistance. This paper presents research investigating the autoftettage process and residual stresses it produces in type 2 CNG storage vessels. A finite element analysis technique and a closed form equation are used. Then, fatigue resistance is analyzed through a fatigue evaluation performed according to ASME section VIII.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.33-36
• /
• 2005

In this research, for the smart health monitoring of the hydrogen storage high pressure composite vessel, the feasibility study of an embedded fiber Bragg grating(FBG) sensor is carried out. To verify strain measurement in various temperature environment which is needed for the hydrogen pressure vessel, tensile test of a composite specimen with both an embedded FBG sensor and a strain gauge is made in low temperature. Before we try a real-size hydrogen storage pressure vessel, a small & cheap composite pressure vessel having the same structure is fabricated with embedded FBG sensors and tested. In the case of an aluminum liner inside the vessel, survivability of FBG sensors at the interface is lower than the other areas.

• 한국안전학회지
• /
• 제34권5호
• /
• pp.7-14
• /
• 2019

The type III vessel, which is used to store high-pressure hydrogen gas, is made by wrapping the vessel's liner with carbon fiber composite materials for strength performance and lightening. The liner seals the internal gas and the composite resists the internal pressure. The properties of the fiber composite material depends on the angle and thickness of the fiber. Thus, engineers should consider these various design variables. However, it significantly increases the design cost due to the trial and error under designing based on experience or experiments. And, for aluminum liners, fatigue loads due to using and charging could give a huge impact on the performance of the structure. However, fatigue failure does not necessarily occur in the position under the highest load in use. Therefore, for hydrogen storage vessel, fatigue evaluation according to design patterns is essential because stress distribution varies depend on composite layer patterns. This study performed an optimization analysis and evaluated a high-pressure hydrogen storage vessel to minimize these trial and error and improve the reliability of the structure, while simultaneously conducting fatigue assessment of all patterns derived from the optimization analysis process. The results of this study are thought to be useful in the strength improvement and life design of composite reinforced high-pressure storage vessels.

• 한국식품저장유통학회지
• /
• 제9권2호
• /
• pp.144-147
• /
• 2002

재료조성이 김치의 저장 중 탄산가스 발생과 용기 압력에 미치는 영향을 조사하기 위하여 재료조성을 달리한 김치를 1$0^{\circ}C$ 에서 저장하면서 pH, 산도, 탄산가스 발생량 및 용기압력의 변화를 측정하였다. 그 결과 마늘을 뺀 김치는 pH감소와 산도의 증가가 완만하였으나 생강, 고춧가루, 젓갈을 뺀 김치는 크게 촉진되었다. 탄산가스 발생량은 대조구와 생강, 고춧가루 및 젓갈을 뺀 김치에서는 저장 3일째부터 높아지기 시작하여 저장 6일째에 최대 값을 나타내었으며 저장 9일째까지 발생이 지속되었다. 김치 담금 재료 중 탄산가스 발생 을 주도하는 재료는 마늘로서 이를 뺀 김치에서는 탄산가스 발생량이 낮았다. 용기압력은 대조구와 생강을 뺀 김치에서 높았으며, 고춧가루, 마늘 및 젓갈을 뺀 김치에서는 비교적 낮았다 또 저장후기에는 전반적으로 감압 상태로 전환되었으며 탄산가스 발생량이 높을수록 감압도가 높았다.

• 공업화학
• /
• 제33권6호
• /
• pp.653-660
• /
• 2022

In liquid hydrogen storage tanks, tank damage or leakage in the surrounding pipes possess a major risk. Since these tanks store huge amounts of the fluid among all the liquid hydrogen process facilities, there is a high risk of leakage-related accidents. Therefore, in this study, we conducted a risk assessment of liquid hydrogen leakage for a grid-type liquid hydrogen storage tank (lattice-type pressure vessel (LPV): 18 m³) that overcame the low space efficiency of the existing pressure vessel shape. Through a commercially developed three-dimensional computational fluid dynamics program, the geometry of the site, where the liquid hydrogen storage tank will be installed, was obtained and simulations of the leakage scenarios for each situation were performed. From the computational flow analysis results, the pool formation behavior in the event of liquid hydrogen leakage was identified, and the resulting damage range was predicted.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.239-245
• /
• 2005

The reduction of heat transfer rate to the stored liquid hydrogen from outside condition is extremely important to keep the liquid hydrogen longer. In this paper the highly efficient support system for the liquid hydrogen storage vessel was newly developed and analysed. The support system was composed of a spherical ball in the center of supporter to reduce the heat transfer area, with its above and below supporting blocks which are the SUS and PTFE blocks inserted in the SUS tube. The heat transfer rate and temperature distribution of the support system were evaluated by FLUENT, and the thermal stress and strain were estimated by ANSYS software. The results showed that the heat transfer rate from outer vessel to inner one was extremely decreased compared with the common method which is simply SUS tubes inserted between inner and outer tanks. The thermal stress and strain were obtained well below the limited values. As a result, it was the most efficient support system of storage vessel for liquid hydrogen and most cryogenic fluids.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.363-369
• /
• 2007

Probably the most significant heat transfer in the cryogenic liquid hydrogen storage tank from the atmosphere may occur through its support system. In this paper the efficient support system for the cryogenic storage vessel was newly developed and analysed. The support system was composed of a spherical ball as a supporter to reduce the contact area. which is located between two supporting SUS tubes inserted SUS and PTFE blocks. Numerical analyses for temperature distribution, and the thermal stress and strain of the support system were performed by the commercial codes FLUENT and ANSYS. The heat transfer rate of the supporter was evaluated by the thermal boundary potential method which can consider the variation of thermal conductivity with temperature. The results showed that the heat transfer rate through the developed supporter compared with the common SUS tube supporter was significantly reduced. The thermal stress and strain were obtained well below the limited values. It was found that the developed supporter can be one of the most efficient support systems for cryogenic liquid storage vessel.