Browse > Article
http://dx.doi.org/10.14346/JKOSOS.2019.34.5.7

A Study on the Design Safety of Type III High-Pressure Hydrogen Storage Vessel  

Park, Woo Rim (Department of Safety Engineering, Pukyong National University)
Jeon, Sang Koo (Department of Safety Engineering, Pukyong National University)
Kim, Song Mi (Department of Safety Engineering, Pukyong National University)
Kwon, Oh Heon (Department of Safety Engineering, Pukyong National University)
Publication Information
Journal of the Korean Society of Safety / v.34, no.5, 2019 , pp. 7-14 More about this Journal
Abstract
The type III vessel, which is used to store high-pressure hydrogen gas, is made by wrapping the vessel's liner with carbon fiber composite materials for strength performance and lightening. The liner seals the internal gas and the composite resists the internal pressure. The properties of the fiber composite material depends on the angle and thickness of the fiber. Thus, engineers should consider these various design variables. However, it significantly increases the design cost due to the trial and error under designing based on experience or experiments. And, for aluminum liners, fatigue loads due to using and charging could give a huge impact on the performance of the structure. However, fatigue failure does not necessarily occur in the position under the highest load in use. Therefore, for hydrogen storage vessel, fatigue evaluation according to design patterns is essential because stress distribution varies depend on composite layer patterns. This study performed an optimization analysis and evaluated a high-pressure hydrogen storage vessel to minimize these trial and error and improve the reliability of the structure, while simultaneously conducting fatigue assessment of all patterns derived from the optimization analysis process. The results of this study are thought to be useful in the strength improvement and life design of composite reinforced high-pressure storage vessels.
Keywords
carbon fiber composite; fatigue analysis; finite element analysis; hydrogen storage vessel; optimization analysis; ply modeling method;
Citations & Related Records
Times Cited By KSCI : 4  (Citation Analysis)
연도 인용수 순위
1 T. H. Lee, "A Study Improvement of Safety Management System of Hydrogen Fuel Cell Vehicle", Master thesis, Ajou University, Korea, 2018.
2 H. G. Kim, Y. M. Choi, S. H. Kim, J. H. Shim and I. C. Hwang, "The Evaluation of Hydrogen Leakage Safety for the High Pressure Hydrogen System of Fuel Cell Vehicle", Transactions of the Korean Hydrogen and New Energy Society, Vol. 23, No. 4, pp. 316-322, 2012.   DOI
3 T. W. David, J. C. Hsieh, N. Chindakham and D. H. Pham, "Optimal Design of a Composite Laminate Hydrogen Storage Vessel", International Journal of Energy Research, Vol. 37, No. 7, pp. 761-768, 2013.   DOI
4 D. S. Son, "Evaluation of Modeling Techniques and Determination of the Autofrettage Pressure for a TYPE III Hydrogen Pressure Vessel", Master thesis, Chung Ang University, Korea, 2013.
5 W. R. Park, N. F. Fatoni and O. H. Kwon, "Evaluation of Stress and Crack Behavior using the Extended Finite Element Method in the Composite Layer of a Type III Hydrogen Storage Vessel", Journal of Mechanical Science and Technology, Vol. 32, No. 5, pp. 1995-2002, 2018.   DOI
6 P. F. Liu, J. K. Chu, S. J. Hou, P. Xu and J. Y. Zheng, "Numerical Simulation and Optimal Design for Composite High-Pressure Hydrogen Storage Vessel: A Review", Renewable and Sustainable Energy Reviews, Vol. 16, No. 4, pp. 1817-1827, 2012.   DOI
7 K. M. Lee, J. S. Park, H. G. Lee and Y. S. Kim, "A Study on Analysis Method to Evaluate Influence of Damage on Composite Layer in Type III Composite Cylinder", Journal of the Korean Society for Composite Materials, Vol. 23, No. 4, pp. 409-417, 2014.
8 J. P. B. Ramirez, D. Halm, J. C. Grandidier, S. Villalonga and F. Nony, "700 bar Type IV High Pressure Hydrogen Storage Vessel Burst-Simulation and Experimental Validation", International Journal of Hydrogen Energy, Vol. 40, No. 38, pp. 13183-13192, 2015.   DOI
9 W. R. Park and O. H. Kwon, "Numerical Analysis of Palladium added Carbon Fiber/Al using Extended Finite Element Method and Multiscale Technique", J. Korean Soc. Saf., Vol. 34, No. 2, pp. 7-14, 2019.   DOI
10 C. P. Fowler, A. C. Orifici and C. H. Wang, "A Review of Toroidal Composite Pressure Vessel Optimisation and Damage Tolerant Design for High Pressure Gaseous Fuel Storage", International Journal of Hydrogen Energy, Vol. 41, No. 47, pp. 22067-22089, 2016.   DOI
11 S. M. Cho, C. J. Kim and Y. G. Kim, "A Study on the Behavior of Ambient Hydraulic Cycling Test for 70 MPa Type 3 Hydrogen Composite Cylinder", Journal of the Korean Institute of Gas, Vol. 16, No. 1, pp. 46-50, 2012.   DOI
12 D. Leh, P. Saffre, P. Francescato, R. Arrieux and S. Villalonga, "A Progressive Failure Analysis of a 700-bar Type IV Hydrogen Composite Pressure Vessel", International Journal of Hydrogen Energy, Vol. 40, No. 38, pp. 13206-13214, 2015.   DOI
13 J. Zheng, Y. Hu, L. Ma and Y. Du, "Delamination Failure of Composite Containment Vessels subected to Internal Blast Loading", Composite Structure, Vol. 130, pp. 29-36, 2015.   DOI
14 J. Zickel, "Isotensoid Pressure Vessels", ARS Journal, pp. 950-951, 1962.
15 Korea Gas Safety Corporation, "Air Charging Safety Management", pp. 40-71, 2018.
16 Y. G. Choi, K. B. Shin and W. H. Kim, "A Study on Size Optimization for Rocket Motor with a Torispherical Dome", Transactions of the Korean Society of Mechanical Engineers, Vol. 34, No. 5, pp. 567-573, 2010.   DOI
17 T. K. Hwang, J. B. Park, H. G. Kim, Y. D. Doh and S. I. Moon, "Dome Shape Design and Performance Evaluation of Composite Pressure Vessel", Journal of the Korean Society for Composite Materials, Vol. 20, No. 4, pp. 31-41, 2007.
18 C. C. Liang, H. W. Chen and C. H. Wang, "Optimum Design of Dome Contour for Filament Wound Composite Pressure Vessels Based on a Shape Factor", Composite Structures, Vol. 58, No. 4, pp. 469-482, 2002.   DOI
19 M. G. Park, "Material Properties and Structure Performance Evaluation of Carbon/Epoxy-Aluminum Type III Hydrogen Storage Vessel", Master thesis, Chung Ang University, Korea, 2011.
20 SIMULIA, lnc., SIMULIA User Assistance 2017, Isight Ver. 2017.
21 SIMULIA, lnc., Wound Composite Modeler for Abaqus user's Manual, Abaqus Ver. 2016.
22 S. M. Cho, M. S. Cho, G. S. Jung, S. K. Lee, S. K. Lee, K. D. Park and S. K. Lyu, "A Study on the Development of a Hybrid Fiber Reinforced Composite for a Type 4 CNG Vessel", Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 4, pp. 97-103, 2017.   DOI
23 J. Zhou, J. Chen, Y. Zheng, Z. Wang and Q. An, "Dome Shape Optimization of Filament-Wound Composite Pressure Vessels Based on Hyperelliptic Functions Considering Both Geodesic and Non-geodesic Winding Patterns", Journal of Composite Materials, Vol. 51, No. 14, pp. 1961-1969, 2017.   DOI
24 R. Willardson, D. Gray and T. DeLay, "Improvements in FEA of Composite Overwrapped Pressure Vessel", CPV Symposium, Belgium, 2011.
25 D. Erni, D. Wiesmann, M. Spuhler, S. Hunziker, E. Moreno, B. Oswald, J. Frohlich and C. Hafner, "Application of Evolutionary Optimization Algorithms in Computational Optics", ACES Journal:Special Issue on Genetic Algorithms, Vo. 15, No. 2, pp. 43-60, 2000.
26 S. W. Tsai, "A Survey of Macroscopic Failure Criteria for Composite Materials", Journal of Reinforced Plastics and Composites, Vol. 3, No. 1, pp. 40-62, 1984.   DOI
27 SIMULIA, lnc., Fe-safe 2018 Fatigue Theory Reference, Ver. 2018.
28 W. R. Park and O. H. Kwon, "Multiscale Stress Analysis of Palladium/Carbon Fiber Composites for the Hydrogen High Pressure Vessel", J. Korean Soc. Saf., Vol. 33, No. 2, pp. 1-7, 2018.   DOI