• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.38-44
• /
• 2018

Ammonia is used primarily as a refrigerant in refrigeration facility and SCR of a plant, and is frequently involved in leakage accidents. This study was conducted by selecting ammonia, a material with a wide influence range when evaluated, as a material with higher vapor pressure and lighter than air. In this study, the influence ranges were computed using KORA(Korea Off-site Risk Assessment supporting tool) with four different environmental factors : ground roughness, sealing, operating temperature, pressure, and leakage hole size. As a result, the difference in the influence range of ground roughness is approximately 4.62 times, while the ammonia storage tank shows a difference in the reduction rate of 0.64 when sealed. The extent of impact increased with increasing leakage depending on storage temperature and pressure, and when storing higher than the saturation vapor pressure, the impact range showed an average growth rate of 3.45 % per 0.1 Mpa($45^{\circ}C$). The influence ranges based on the size of the leakage holes is shown to be proportional to the area of the leakage zone.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.2
• /
• pp.141-154
• /
• 2015

In general, conventional criticality analysis for spent fuel transport/storage systems have been performed based on the assumption of fresh fuel concerning the potential uncertainties from number density calculations of actinide nuclides and fission products in spent fuel. However, these evaluation methods cause financial losses due to an excessive criticality margin. In order to overcome this disadvantage, many studies have recently been conducted to design and commercialize a transportation and storage cask applied to the Burnup Credit (BUC). This study conducted an assessment to ensure criticality safety for reactor operating parameters, axial burn-up profiles and misload accident conditions, which are the factors that are likely to affect criticality safety when the BUC is applied to the dual-purpose cask under development at the KOrea RADioactive waste agency (KORAD). As a result, it was found that criticality resulting from specific power, changed substantially and relied on conditions of low enrichment and high burn-up. Considering the end effect in the case of high burn-up produced a positive-definite result. In particular, the increment of maximum effective multiplication factors due to misloading was 0.18467, confirming that misload is a factor that must be taken into account when applying the BUC. The results of this study may therefore be utilized as references in developing technologies to apply the BUC to domestic models and operational procedures or preventing any misload accidents during the process of spent fuel loading.

• Korean journal of applied entomology
• /
• v.22 no.2 s.55
• /
• pp.138-146
• /
• 1983

With the increase of pesticide consumption, not only pesticide handling population would grow greater but also the chances to be exposed to the pesticides would be also increased. Thus, safe use and handling of the pesticides are becoming more important and serious in these days. The pesticides are well known to most pepole, however there are very limited number of persons who have correct understanding of chamicals. Intoxication cases caused by pesticides have been reported very rarely through the mess media, even they were lack of scientific evidences. In this paper, problems related to pesticide manufacture, transportation, storage, sprays, and residues and their countermeasures were discussed in connection with public health and enviromental aspects. Acute intoxication cases by pesticide handling might be caused accidently either through manufacture, marketing, transportation, or spraying. Safety aspects of workers in manufacturing plants include not only exposure to toxic chemicals, but also posibilities of of explosion and brought about by pesticides and their diluents. The problems of water pollution by waste chemicals from the manufacturing factories were discussed. Packing and loading methods of pesticides for transportation are considered in safety scheme and discussions are given in association with traffic accidents. With regard to warehouse, the pesticide storage, location structure, keepers, and standing materials for emergency are concerned with safety aspects. Concerning the spraying of chemicals, there are some problems to be discussed about clothes, spray equipment, wind direction, spray period, and spray workers condition. After the spray, treatment of used containers, remainder of Pesticides, and spray tools are also discussed. For the dissolutions of problems on public health and environmental danger arising from pesticide residues, there are two legal sanctions; 'Pesticide Tolerances' and 'Pesticide Safe Use Standards'. These regulations are legally effective, however, some problems still remain in practices to implement the acts properly, because these provisions are followed by the far mers mostly. With these regards, most problems are concerned with various sectors and persons, affecting public health and environment from the producers to the end users and consumers. As a whole persons concerned with pesticides, every possible effort has to be assembled to protect hazards from the chemicals. For the foremost place, special training and education are required for managing groups; such as factory managers and agricultural extension workers who are responsible for training the factory workers and farmers. The education is the only way to solve the hazard problems caused by the pesticides.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.95-103
• /
• 2017

A lot of hazardous materials have been used for product processing and utility plant. Many accidents including toxic release, fire and explosions occur in the ammonia related facility and plant. Various safety and environment management program including PSM, SMS, ORA etc. are being implemented for risk management and accident prevention in the production industry. Also much study and research have been carried about risk assessment of accident scenario in the academic and research area. In this paper, firstly risk level was assessed by using a typically used KORA program and LOPA PFD method for the selected ammonia unloading and storage facility. And then risk reduction measures for the risk assessed facility were studied in 3 aspects and some measures were proposed. Those Risk Reduction measures are including a leak detection and emergency isolation, water spray, dilution tank, dike and trench, scattering protection in hardware impovement aspect, and a applicable risk criteria, conditional modifier for existing LOPA PFD, alternative supporting modeling program in risk estimation methodology aspect, and last RBPS(Risk Based Process Safety) program, re-doing of process hazard analysis, management system compliance audit in managerial activity aspect.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.312-321
• /
• 2018

The Korean DR market proposes suppression of peak demand under reliability crisis caused a natural disaster or unexpected power plant accidents as well as saving power plant construction costs and expanding amount of reserve as utility's perspective. End-user is notified a DR event signal DR execution before one hour, and executes DR based on requested amount of load reduction. This paper proposes a DR energy management algorithm that can be scheduled the optimal operations of chiller system and ESS in the next day considering the TOU tariff and DR scheme. In this DR algorithm is divided into two scheduling's; day-ahead operation scheduling with temperature forecasting error and operation rescheduling on DR operation. In day-ahead operation scheduling, the operations of DR resources are scheduled based on the finite number of ambient temperature scenarios, which have been generated based on the historical ambient temperature data. As well as, the uncertainties in DR event including requested amount of load reduction and specified DR duration are also considered as scenarios. Also, operation rescheduling on DR operation day is proposed to ensure thermal comfort and the benefit of a COB owner. The proposed method minimizes the expected energy cost by a mixed integer linear programming (MILP).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.541-550
• /
• 2019

An emergency generator is key equipment for fire-fighting to supply power to fire-fighting facilities, which protect property and people in cases of fire accidents. A rated load test for emergency generators must be carried out by connecting an emergency load to the generator in accordance with related regulations. However, a no-load test has been performed for emergency generators in general since serious problems can occur when the main power is cut off, including the damage of customer devices and shut down of critical loads. Therefore, this paper proposes a load test method for an emergency generator using energy storage system (ESS) without the interruption of main power. The emergency power system was also modeled based on PSCAD/EMTDC software, and a 200-kW scale ESS load test device was implemented. The simulation and test results show that the load test method is useful and practical for an emergency power supply system.

• Industry Promotion Research
• /
• v.9 no.2
• /
• pp.37-44
• /
• 2024

This study selected the worst-case scenario for fireball and vapor cloud explosion (VCE) of a styrene monomer storage tank installed in a petrochemical production plant and performed damage prediction and accident impact analysis. The range of influence of radiant heat and overpressure due to fireball and vapor VCE during the abnormal polymerization reaction of styrene monomer, the main component of the mixed residue oil storage tank, was quantitatively analyzed by applying the e-CA accident damage prediction program. The damage impact areas of radiant heat and explosion overpressure are analyzed to have a maximum radius of 1,150m and 626m, respectively. People within 1,150m of radiant heat of 4kW/m2 may have their skin swell when exposed to it for 20 seconds. In buildings within 626m, where an explosion overpressure of 21kPa is applied, steel structures may be damaged and separated from the foundation, and people may suffer physical injuries. In the event of a fire, explosion or leak, determine the risk standards such as the degree of risk and acceptability to workers in the work place, nearby residents, or surrounding facilities due to radiant heat or overpressure, identify the hazards and risks of the materials handled, and establish an emergency response system. It is expected that it will be helpful in establishing measures to minimize damage to workplaces through improvement and investment activities.

• Journal of Radiation Industry
• /
• v.18 no.1
• /
• pp.35-42
• /
• 2024

Demand for RW transportation is expected to increase due to the continuous generation of RW from nuclear power plants and facilities, decommissioning of plants, and saturation of spent fuel temporary storage facilities. The locational aspect of plants and radiation protection optimization for the public have led to an increasing demand for maritime transportation, necessitating to apprehend the overseas and domestic current status. Given the potential long-term radiological impact on the public in the event of a sinking accident, a pre-transportation exposure assessment is necessary. The objective of this study is to investigate the overseas and domestic RW maritime transportation current status and overseas dose assessment cases for the public in sinking accident. Selected countries, including Japan, UK, Sweden, and Korea, were examined for transport cases, Japan and the U.S were chosen for dose assessment case in sinking accidents. As a result of the maritime transportation case analysis, it was performed between nuclear power plants and reprocessing facilities, from plants to disposal or intermediate storage facilities. HLW and MOX fuel were transported using INF 3 shipments, and all transports were performed low speed of 13 kn or less. As a result of the dose assessment for the public in sinking accident, japan conducted an assessment for the sinking of spent fuel and vitrified HLW, and the U.S conducted for the sinking of spent fuel. Both countries considered external exposure through swimming and working at seashore, and internal exposure through seafood ingestion as exposure pathway. Additionally, Japan considered external exposure through working on board and fishing, and the U.S considered internal exposure through spray inhalation and desalinized water and salt ingestion. Internal exposure through seafood ingestion had the largest dose contribution. The average public exposure dose was 20 years after the sinking, 0.04 mSv yr^-1 for spent fuel and 5 years after the sinking, 0.03 mSv yr^-1 for vitrified HLW in Japan. In the U.S, it was 1.81 mSv yr^-1 5 years after the sinking of spent fuel. The results of this study will be used as fundamental data for maritime transportation of domestic RW in the future.

• Journal of the Korean Institute of Gas
• /
• v.17 no.6
• /
• pp.73-82
• /
• 2013

With remarkable development of industry and technology, various chemical articles are developed to improve the quality of human life, yet some of chemicals are hazardous to human and the environment. However, safety control of chemical articles such as transportation, storage, and handling is emerging as a major issue lately. The road transportation needs well-organized safety management system, especially it has high probability of accidents. In this research, we point out problems in current state and related regulation of transportation of dangerous goods to compare the regulation in UN-RTDG. In addition, we suggest the enhancement law, the plan for standardization of classification in road transportation of dangerous goods and harmonization of labeling in transportation of dangerous goods to contribute to human health and environment protection.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.3
• /
• pp.341-347
• /
• 2015

This study aims to design a chief VDR(Voyage Data Recorder) system which is appropriate to small and medium sized vessels and also implement the data about marine communication devices, sensors, etc. to be stored or printed at the navigator when those data are connected to VDR through data communication between marine navigation and VDR which are based on serial communication or internet in order to prove efficiency of the marine navigator. Also, the design of VDR is intended to be small and light in order to expand to apply it to small and medium vessels, which enables to analyze causes of marine accidents precisely through its characteristic functions which are the same as those at "vehicle mounted black-box" (location of the car, image and voice storage) by which the same roles are played on land.