• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.98-104
• /
• 2009

The objective of this paper is to investigate the effect of factors on the dynamic stiffness variation of boring bar. The experiment was carried out by Taguchi Method and Orthogonal array table. The results indicate that overhang was found out to be dominant factor with 95% confident intervals and feed rate and depth of cut were insignificant. In addition, analysis of loss function shows that loss value increased sharply from 3D to 4D(D is a shank diameter). Consequently, there is critical point which changes property of dynamic stiffness.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.125-128
• /
• 2006

Many research have been carried out concerned with the flexural performance of FRP composite in a various ways. Most of them, however, have used a small-scale specimen, so haven't been fully verified by full-scale model test. In this study, a full-scale RC beam model test for flexural strengthening with CFRP composites has been performed in order to verify test results obtained through a series of small-scale model test with respect to FRP stiffness affecting strengthening performance in the previous studies. A total of 4 specimens have been manufactured including control beam. The specimens strengthened with CFRP composites consist of 3 different CFRP stiffness with 2 types of CFRP composite. Consequently, the purpose of this study is to estimate influence of the size effect of specimens and FRP stiffness on the flexural performance. As a result, the effective strain of FRP composite is inversely proportional to FRP stiffness and ensures the same performance with small-scale model test.

• 한국정밀공학회지
• /
• 제18권12호
• /
• pp.145-151
• /
• 2001

The dimensional accuracy of the cold forged part is depended on the elastic characteristics of the die. To increase the stiffness of the prestressed die, the first stress ring of the tungsten carbide alloy (WC) is considered. For the design, Lame's equation is used. Diameter ratios and interferences have been determinated by maximum inner pressure without yielding of materials. The design of the prestressed die has been compared with the conventional one. For the comparison, the FE-analysis using ANSYS has been performed. The results indicate that the prestressed die with the high stiffness can be obtained by the using the high stiffness material as the first stress ring.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3109-3117
• /
• 1994

To operate a flexible mechanism in high speed its weight must be reduced as far as the structural strength does not decrease too much, but a light-weighted mechanism causes undesirable elastodynamic responses deteriorating the system performance. Besides, clearance within the connections of mechanisms causes rapid wear, increased noise and vibration. Even if the problems described above must be considered in the initial design stage, there has been no effective design process which takes account of the correlation between dynamic characteristics of flexible mechanism and the clearance effect at the joint. In this study, the generalized elastodynamic governing equations which include dynamic characteristics and boundary conditions of flexible mechanism are derived by variational calculus and solved by using FFM theory. To take the clearance effect at joint into account a new dynamic model is presented and also the method of modified stiffness/damping matrix is proposed to activate the dynamic clearance model, which cooperates with the developed governing equation very easily. As the results of this study, the proposed method(modified stiffness/damping matrix) to calculate clearance effect was proved to be superior to the existing one(force reaction method) in solution convergency and calculation performance. Besides this method can be easily adopted to the complex shape joint without calculation of reaction force direction.

• 대한기계학회논문집A
• /
• 제35권3호
• /
• pp.333-340
• /
• 2011

본 연구에서는 복합소재 단일겹치기 조인트의 접착부재 형상 및 필렛 유무에 따른 응력집중 완화 효과를 평가하였다. 이를 위해 6가지 서로 다른 끝단부 형상에 대해 비선형 유한요소 해석을 수행하였다. 또한, 복합재 접착부재와 접착제의 다양한 강성비에 따른 6가지 모델의 최대 전단 및 수직응력의 변화를 고찰하였다. 접착부재가 순방향 테이퍼를 갖는 모델의 경우에는 가장 높은 응력값을 보여 조인트의 접합강도가 가장 취약할 것으로 예상되었다. 이에 반해, 접착부재가 역방향 테이퍼를 갖고 필렛이 존재할 경우 가장 낮은 응력값을 보였다. 접착부재와 접착제의 강성변화에 따른 최대응력 변화를 고찰한 결과 접착부재의 강성은 클수록, 접착제 강성은 낮을수록 응력집중은 완화되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1298-1301
• /
• 2003

The purpose of this research is to evaluate the effect of pre-load and fatigue life of the distracted one-level pedicle screw system. A spring, which acted as a substitute of the ligament, was installed in the one-level pedicle screw system before testing. The static and fatigue properties are now being tested, which includes 6mm rod to 6mm screw, 6mm rod to 6.5mm screw and 6.35mm rod to 6.5mm screw, under pre-load. Until now as test data were analyzed, 6mm rod to 6.5mm screw was found to have the best performances of stillness and fatigue lift, while 6mm rod to 6mm screw showed the shortest fatigue life. If the stiffness of screw was bigger than that of rod. the fatigue life was prolonged. The fatigue life of the distracted pedicle screw was proved to be shorter than that of the one-level pedicle screw system. So the fatigue life was shortened because of the effect of the spring on the flexibility and stiffness of the rod. In order to obtain the stability of the pedicle screw, more tests are under doing on this topic.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.229-232
• /
• 2008

콘크리트를 강재 주형의 내부에 충진시킨 형태의 거더 형식은 구조적인 성능의 향상 이외에도 유지관리의 수월성과 외관상의 장점으로 인해 활발히 연구 개발되고 있다. 본 연구에서는, 내부를 무근 콘크리트로 충진한 형식의 강 콘크리트 합성 거더 형식의 내부 전단연결부 특성에 대한 연구의 일부로서, 외부 강재에 의한 구속효과가 내부 전단연결부의 강도에 미치는 영향을 검토하였다. 강재에 의해 구속된 콘크리트의 전단연결부는 구속효과로 인해 전단연결부의 강도가 증가하는 경향을 보일 것으로 예상되며, 이를 검토하기 위해 구속효과를 파라미터로 한 실험을 수행하였으며, 그 결과를 본 논문에서 보이고자 한다.

• Structural Engineering and Mechanics
• /
• 제67권2호
• /
• pp.165-173
• /
• 2018

A simple predicted model using a modified Shear-lag method was used to represent the moisture absorption effect on the stiffness degradation for $[0/90]_{2s}$ composite laminates with transverse cracks and under flexural loading. Good agreement is obtained by comparing the prediction model and experimental data published by Smith and Ogin (2000). The material properties of the composite are affected by the variation of temperature and moisture absorption. The transient and non-uniform moisture concentration distribution give rise to the transient elastic moduli of cracked composite laminates. The hygrothermal effect is taken into account to assess the changes in the normalised axial and flexural modulus due to transverse crack. The obtained results represent well the dependence of the stiffness properties degradation on the cracks density, moisture absorption and operational temperature. The composite laminate with transverse crack loaded in axial tension is more affected by the hygrothermal condition than the one under flexural loading. Through this theoretical study, we hope to contribute to the understanding of the moisture absorption on the composite materials with matrix cracking.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.718-723
• /
• 2007

A three dimensional multibody modeling of a launcher system was developed and dynamic characteristics of the system was carried out. All the components were modeled as rigid bodies, All the components of system, ie; chassis, turret, cage and suspension parts, are modeled as rigid. The force interaction between the ground and tire was modeled as a point contact model. The factors were selected as cause and effect diagram of the MINITAB. To see effect of the stiffness, damping, mass at the launcher system, several cases of suspension parameters were compared and optimal values were selected. The stiffness and the damping coefficient were selected as design variables to minimize the required time for the next fire. The dynamic simulation was carried out using the ADAMS, and the MINITAB was employed for data analysis.

• 한국전기전자재료학회논문지
• /
• 제19권4호
• /
• pp.309-313
• /
• 2006

Pad surface characteristics such as roughness, groove and wear rate of pad have a effect on the within wafer non-uniformity(WIWNU) in chemical mechanical polishing(CMP). Although WIWNU increases as the uniformity of roughness(Rpk: Reduced peak height) becomes worse in an early stage of polishing time, WIWNU decreases as non-uniformity of the Rpk value. Also, WIWNU decreases with the reduction of the pad stiffness, though original mechanical properties of pad are unchanged by the grooving process. In addition, conditioning process causes the inequality of pad wear during in CMP. The profile of pad wear generated by the conditioning process has a significant effect on the WIWNU. These experiments results could help to understand the effect of pad surface characteristics in CMP.