• Advances in aircraft and spacecraft science
• /
• v.5 no.3
• /
• pp.385-400
• /
• 2018

In this paper dynamic behavior (modal analysis and dynamic transient response) of a novel sandwich T-joint is numerically and experimentally investigated. An epoxy adhesive is selected for bonding purpose and making the step wise graded behavior of adhesive region. The effect of the step graded behavior of the adhesive zone on dynamic behavior of a sandwich T-joint is numerically studied. Finite element analysis (FEA) of the T-joints with carbon fiber reinforced polymer (CFRP) face-sheets is performed by ABAQUS 6.12-1 FEM code software. Modal analysis and dynamic half-sine transient response of the sandwich T-joint are presented in this paper. Two verification processes employed to verify the dynamic modeling of the manufactured sandwich panels and T-joint modeling. It has been shown that the step wise graded adhesive zone cases have changed the second natural frequency by about 5%. Also, it has been shown that the different arranges in the step wise graded adhesive zone significantly affect the maximum stresses due to transient dynamic loading by 1112% decrease in maximum peel stress and 691.9% decrease in maximum shear stress on the adhesive region.

• Smart Structures and Systems
• /
• v.30 no.2
• /
• pp.173-181
• /
• 2022

The current paper presents a technique to detect crack in non-uniform cantilever-type pipe beams, that have step changes in the properties of their cross sections, restrained by a translational and rotational spring with a tip mass at the free end. An equation for estimating the natural frequencies for the non-uniform beams is derived using the boundary and continuity conditions, and an equivalent bending stiffness for cracked beam is applied to calculate the natural frequencies of the cracked beam. An experimental study for a step-changed non-uniform cantilever-type pipe beam restrained by bolts with a tip mass is carried out to verify the proposed method. The translational and rotational spring constants are updated using the neural network technique to the results of the experiment for intact case in order to establish a baseline model for the subsequent crack detection. Then, several numerical simulations for the specimen are carried out using the derived equation for estimating the natural frequencies of the cracked beam to construct a set of training patterns of a neural network. The crack locations and sizes are identified using the trained neural network for the 5 damage cases. It is found that the crack locations and sizes are reasonably well estimated from a practical point of view. And it is considered that the usefulness of the proposed method for structural health monitoring of the step-changed non-uniform cantilever-type pipe beam-like structures elastically restrained in the ground and have a tip mass at the free end could be verified.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.6 s.348
• /
• pp.1-8
• /
• 2006

In the asynchrous OFCDM(Orthogonal Frequency and Code Division Multiplexing) system, a three-step cell search algorithm is performed for the initial synchronization in the following three steps: OFCDM symbol timing, i.e., Fast Fourier Transform(FFT) window timing is estimated employing guard interval (GI) correlation in the first step, then the frame timing and CSSC (Cell Specific Scrambling Code) group is detected by taking the correlation of the CPICH(Common Pilot Channel) based on the property yeilded by shifting the CSSC phase in the frequency domain. Finally, the CSSC phase within the group is identified in the third step. This paper proposes a modification code(PCSSCG:Patial Cell Specific Scrambling Code Group) of the conventional CPICH based cell search algorithm in the second step which offers MS(Mobile Station) complexity reductions with the nearly same performance. The proposed method is to be compared and verified through the computer simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.6B
• /
• pp.697-709
• /
• 2011

For improvement of wireless Internet service quality at vehicle's moving speed, it is advised to reduce the service disruption time by reducing the handover frequency on vehicle's moving path. Particularly, it is advantageous to avoid the handover to cell whose dwell time is short or can be ignored in terms of service continuity and average throughput. This paper proposes the handover scheme that is suitable for vehicle in order to improve the wireless Internet service quality. In the proposed scheme, the handover process continues to be learned before being modeled to Discrete-Time Markov Chain (DTMC). This modeling reduces the handover frequency by preventing the handover to cell that could provide service sufficiently to passenger even when vehicle passed through the cell but there was no need to perform handover. In order to verify the proposed scheme, we observed the average number of handovers, the average RSSI and the average throughput on various moving paths that vehicle moved in the given urban environment. The experiment results confirmed that the proposed scheme was able to provide the improved wireless Internet service to vehicle that moved to some degree of consistency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.1
• /
• pp.139-149
• /
• 2007

Asynchronous OFCDM(Orthogonal Frequency and Code Division Multiplexing) systems must have a cell search process necessarily unlike synch개nous systems. this process is hewn initial synchronization and a three-step cell search algorithm is performed for the initial synchronization in the following three steps: OFCDM symbol timing, i.e., Fast Fourier Transform(FFT) window timing is estimated employing guard interval (GI) correlation in the first step, then the frame timing and CSSC(Cell Specific Scrambling Code) group is detected by taking the correlation of the CPICH(Common Pilot Channel) based on the property yielded by shifting the CSSC phase in the frequency domain. Finally, the CSSC phase within the group is identified in the third step. This paper proposes a modification group code with two or three block of the conventional CPICH based cell search algorithm in the second step which offers MS(Mobile Station) complexity reductions. however, the effect of the reduction complexity leads to degradation of the performance therefore, look for combination to have the most minimum degradation. the proposed block type group code with suitable combinations is the nearly sane performance as conventional group code and has a complexity reduction that is to be compared and verified through the computer simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.636-644
• /
• 2009

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and step-impedance-open-stub(SIOS) for wireless data communication. The SIOS can be reduce length about 30% more than general $0.25{\lambda}$ stub. And the stub can the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter has 3dB fractional bandwith of 52.5%(3.267GHz), an insertion loss of better than 0.33dB from 4.587GHz to 7.854GHz, and two rejection of greater than 30dB within 221MHz$(4.366GHz{\sim}4.587GHz)$ at low frequency band, 181MHz$(7.854GHz{\sim}8.035GHz)$ at high frequency band. Maximum rejection characteristics of the filter are -54dB at low frequency and -60dB at high frequency.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.53-58
• /
• 2018

A novel X-band high speed frequency sweep signal generator based on a tunable optoelectronic oscillator (OEO) incorporating a frequency-swept laser is presented and the theoretical fundamentals of the design are explained. A prototype of the generator with tuning range from 8.8552 GHz to 10.3992 GHz and a fine step about 8 MHz is achieved. The generated radiofrequency signal with a single sideband (SSB) phase noise lower than -100 dBc/Hz@10KHz is experimentally demonstrated within the whole tunable range, without any narrow RF band-pass filters in the loop. And the tuning speed of the frequency sweep signal generator can reach to over 1 GHz/s benefiting from applying a novel dispersion compensation modular instead of several tens of kilometers of optical fiber delay line in the system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.8
• /
• pp.1259-1265
• /
• 2003

We present a new post-fabrication frequency tuning method for laterally driven electrostatic microresonators using a DC-biased electrostatic comb array of linearly varied finger-length. The electrostatic tuning force and the equivalent stiffness, adjusted by the DC-biased tuning-comb array, have been formulated as functions of geometry and DC tuning voltage. A set of frequency-turnable microresonators has been designed and fabricated by 4-mask surface-micromachining process. The resonant frequency of the microfabricated microresonator has been measured for a varying tuning voltage at the reduced pressure of 1 torr. The maximum 3.3% reduction of the resonant frequency is achieved at the tuning voltage increase of 20V.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.6 no.6
• /
• pp.32-41
• /
• 1992

In this paper, an advanced Pulse Width Modulation Inverter strategy for driving a variable-speed induction motor is introduced. A switching pattern making use of the near-proportionality of voltage and frequency in AC machines operating with constant flux was computed. At low magnitudes and ow frequencies of the fundamental, many more harmonics are eliminated than at high magnitudes and frequencies. In order to keep the inverter switching frequency constant over the output frequency range, the chopping frequency is diminished as the frequency of the fundamental increases. Using these modulation strategy, the harmonics components of PWM inverter are efficiently eliminated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.10
• /
• pp.1262-1272
• /
• 1997

An experimental study on the frequency control of an inverter heat pump to get the desired indoor room temperature has been conducted for the performance characteristics during the steady, 4, 8, and 16 step frequency operations. The heat pump model used in this study was operated to meet the experimental conditions of ASHRAE standard. The performance of the system was tested by measuring the temperature and pressure of the refrigerant, and cooling capacity, power consumption, etc. of the system. As the controlling frequency steps increased, the running time of the compressor increased as well as the electric consumption of the system and the cooling energy due to the wall heating load. However, the average cooling COP was improved.