• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.12
• /
• pp.29-35
• /
• 2008

In this paper, The author present a load current feed-forward compensator by method that improve voltage controller of Step-down Chopper to get stable output voltage to sudden change of load current. To confirm the characteristics of a presented load current feed-forward compensator compared each transfer function of whole system that load current feed-forward compensator is added with transfer function of whole system that existent voltage controller is included using Mason gains formula in Root locus and Bode diagram. As a result the pole of system is improved, extreme point of the wave and system improves, and size of peak value and phase margin of break frequency in resonance frequency confirmed that is good. Therefore, presented control technique could confirm that reduce influence by perturbation and improves stationary state and dynamic characteristics in output of Step-down Chopper.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.846-857
• /
• 2019

Voltage step-down converters are very popular in distributed power systems, voltage regular modules, electric vehicles, etc. However, a high step-down voltage ratio is required in many applications to prevent the traditional buck converter from operating at extreme duty cycles. In this paper, a series capacitor interleaved buck converter with a soft switching technique is proposed. The DC voltage ratio of the proposed converter is half that of the traditional buck converter and the voltage stress across the one main switch and the diodes is reduced. Moreover, by paralleling the series connected auxiliary switch and the auxiliary inductor with the main inductor, zero voltage transition (ZVT) of the main switches can be obtained without increasing the voltage or current stress of the main power switches. In addition, zero current turned-on and zero current switching (ZCS) of the auxiliary switches can be achieved. Furthermore, owing to the presence of the auxiliary inductor, the turned-off rate of the output diodes can be limited and the reverse-recovery switching losses of the diodes can be reduced. Thus, the efficiency of the proposed converter can be improved. The DC voltage gain ratio, soft switching conditions and a design guideline for the critical parameters are given in this paper. A loss analysis of the proposed converter is shown to demonstrate its advantages over traditional converter topologies. Finally, experimental results obtained from a 100V/10V prototype are presented to verify the analysis of the proposed converter.

• Physical Therapy Korea
• /
• v.29 no.4
• /
• pp.249-254
• /
• 2022

Background: The lateral step down (LSD) is a form of stair negotiation used by the elderly because it requires less movement of the lower extremity. Although it is necessary to study the amount of pelvic drop and the strength of a hip abductor during LSD for intervention, limited studies have investigated the relationship between the amount of pelvic drop and strength of a hip abductor during LSD in elderly people. Objects: This study aimed to determine the relationship between the amount of pelvic drop on an unsupported leg and the strength of the hip abductor during LSD in the elderly. Methods: Thirty elderly people (male: 17, female: 13) were recruited. Subjects performed the LSD task, and the evaluator measured and the amount of pelvic drop on an unsupported side. Also, the isometric strength of the hip abductor was measured in a supine position. Results: We found significant relationships between the strength of the hip abductor and the amount of pelvic drop (r = -0.386). The average hip abductor strength normalized by body weight was 1.06 N/kg (max: 1.99, min: 0.52) and the average contralateral pelvic drop (CPD) angle was 4.16° (max: 15.3, min: 0). Conclusion: Our results indicated that the strength of the hip abductor had a moderate correlation with the CPD during a LSD in the elderly. Hip abductor weakness could translate into altered movement of the pelvis.

• Ocean Systems Engineering
• /
• v.1 no.4
• /
• pp.263-283
• /
• 2011

The performance of a rig tie-down system on a TLP (Tension Leg Platform) is investigated for 10-year, 100-year, and 1000-year hurricane environments. The inertia loading on the derrick is obtained from the three-hour time histories of the platform motions and accelerations, and the dynamic wind forces as well as the time-dependent heel-induced gravitational forces are also applied. Then, the connection loads between the derrick and its substructure as well as the substructure and deck are obtained to assess the safety of the tie-down system. Both linear and nonlinear inertia loads on the derrick are included. The resultant external forces are subsequently used to calculate the loads on the tie-down clamps at every time step with the assumption of rigid derrick. The exact dynamic equations including nonlinear terms are used with all the linear and second-order wave forces considering that some dynamic contributions, such as rotational inertia, centripetal forces, and the nonlinear excitations, have not been accounted for in the conventional engineering practices. From the numerical simulations, it is seen that the contributions of the second-order sum-frequency (or springing) accelerations can be appreciable in certain hurricane conditions. Finally, the maximum reaction loads on the clamps are obtained and used to check the possibility of slip, shear, and tensile failure of the tie-down system for any given environment.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.63-68
• /
• 2009

The power management integrated circuit(PMIC) for CCD image sensor is presented in this study. A CCD image sensor is very sensitive against temperature. The temperature, that is heat, is generally generated by the PMIC with low efficiency. Since the generated heat influences performance of CCD image sensor, it should be minimized by using a PMIC which has a high efficiency. In order to develop the PMIC with high efficiency, the input stage is designed with synchronous type step down DC-DC converter. The operating range of the converter is from 5V to 15V and the converter is controlled using PWM method. The PWM control circuit consists of a saw-tooth generator, a band-gap reference circuit, an error amplifier and a comparator circuit. The saw-tooth generator is designed with 1.2MHz oscillation frequency. The comparator is designed with the two stages OP Amp. And the error amplifier has 40dB DC gain and $77^{\circ}$ phase margin. The output of the step down converter is connected to input stage of the charge pump. The output of the charge pump is connected to input of the LDO which is the output stage of the PMIC. Finally, the PMIC, based on the PWM control circuit and the charge pump and the LDO, has output voltage of 15V, -7.5V, 3.3V and 5V. The PMIC is designed with a 0.35um process.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.340-341
• /
• 2011

본 논문에서는 높은 승 강압비를 갖는 양방향 DC-DC 컨버터에 대한 최적의 스위칭 기법을 제안한다. 제안한 컨버터는 CCM에서도 소프트 스위칭이 가능하여 스위칭 손실뿐만 아니라 인덕터의 발열도 줄일 수 있다. 또한 모든 소자의 전압 정격과 수동소자의 부피도 기존 양방향 컨버터 보다 작아 고효율 및 고전력밀도의 달성을 기대 할 수 있다. 1.5kW 시작품의 실험을 통해 본 논문의 타당성을 검증하였다.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2012.05a
• /
• pp.83-85
• /
• 2012

Gait analysis through wearable sensors is becoming a key research topic in mobile. In gait analysis, step detection is one of the most important processes that will lay down the foundation for future implementation. In this paper, we will propose a simpler algorithm to determine and analyze the steps using accelerometer sensor built-in mobile phone that physically placed into the trouser pocket. This is the location where most of mobile devices are. With 5 volunteers walking in 160 seconds, the accuracy of this method is approximately 98.5%.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1931-1933
• /
• 1998

In this paper, single-phase PWM AC to AC converter that operates with unit power factor and sinusoidal input line currents is presented. The output voltage of this converter is able to be obtain step up voltage as well as step down voltage. because the converter applies to operating method of buck-boost converter. The control of this converter is performed with PI control method. By using this control method low lipples in the output current and the voltage as well as fast dynamic response are achieved.

• Journal of Ginseng Research
• /
• v.20 no.3
• /
• pp.226-232
• /
• 1996

This study was performed to investigate the effect of red ginseng extract including some vitamin B groups as test drug on learning and memory in mice. Single and repeated administrations of the test drug improved the acquisition and the process of consolidation in the tests using step-through and step-down apparatus, indicating this test drug improved learning and memory. However, the test drug did not improve scopolamine-induced amnesia. These results suggest that test drug may be useful as a nootropic agent.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.318-320
• /
• 2007

Single-phase cycloconverters are widely used for ac-ac power conversion especially for speed control of ac drives. In this paper, a new single-phase to single-phase Z-source cycloconverter topology is proposed. The proposed single-phase Z-source cycloconverter can boost to a desired voltage with various frequency. Thus, it is called a frequency step-down and amplitude voltage step-up converter. The operating principle of the proposed topology is presented. Analysis and simulation for this single-phase Z-source cycloconverter are also presented.